Cabletron Systems 9F426-03 Documento tecnico

9032058-01

SmartSwitch 9000

9F426-03

Local Management Appendix

Appendix

9F426-03 Module Speciﬁc

Information

Introduction

This appendix contains local management information that is speciﬁc to the

9F426-03 FDDI Switch Module.

Module Interfaces

The 9F426-03 FDDI Switch Module has 8 interfaces. Table 1 lists the identifying

number, name, and description of each interface.

Table 1. 9F426-03 FDDI Switch Module Interfaces

Interface

Number

Interface

Name

Interface

Description

1 SMB1 1 Mbps System Management Bus

2 SMB10 10 Mbps System Management Bus

3 HOST i960 Host

4 CONTROL i960 Data Controller

5 INB Internal Network Bus

6 FRONT1 FDDI Front Panel Port 1

7 FRONT2 FDDI Front Panel Port 2

8 FRONT3 FDDI Front Panel Port 3

9F426-03 Module Speciﬁc Information

Use the numbers listed in Table 1 to conﬁgure the module’s default interface (see

General Conﬁguration Screen in the

SmartSwitch 9000 Module Local Management

User’s Guide

9F426-03 Module Speciﬁc Information

Ring Map Conﬁguration Screen

The Ring Map Conﬁguration Screen (Figure 1), contains conﬁguration and

connection information and displays the topology of the FDDI rings connected to

the module.

Figure 1. Ring Map Conﬁguration Screen

SmartSwitch 9000 Local Management

Ring Map Configuration

Module Name: 9F426-03 Firmware Revision: 01.04.10

Slot Number: 11 BOOTPROM Revision: 01.02.00

FDDI Address: 00:00:B8:00:10:62 MAC Count: 1

Current RingMap: FRONT PANEL 1 (isolated) Address Mode: [MAC]

00:00:B8:00:10:62 (NAS) <<<<<<<<<<<<<<<<<<< SMT-Unknown-Address

[FRONT PANEL 1 (isolated)] EXIT RETURN

9F426-03 Module Speciﬁc Information

Ring Map Conﬁguration Screen Fields

The following information brieﬂy explains each Ring Map Conﬁguration Screen

ﬁeld.

FDDI Address

Displays the address of the module. The format of this address (either MAC or

Canonical) is determined by the value you select in the Address Mode ﬁeld.

MAC Count

Displays the number of MACs (Media Access Controllers) that are attached to the

speciﬁed ring.

Current Ring Map

Identiﬁes the ring on which a MAC for the speciﬁed module resides, and whether

that MAC is located on the primary or secondary path of that ring.

Address Mode (Toggle)

Allows you to select the format in which addresses appear on this screen. Press

the

Space Bar

to toggle to the desired value. The Address Mode possibilities are:

• MAC

• Canonical

FRONT PANEL x (Toggle)

Allows you to display information about the module’s front panel ports.

Choosing a Front Panel Port

To choose a front panel port:

1. Use the arrow keys to highlight the FRONT PANEL x ﬁeld (lower left corner

of screen).

2. Press the

Space

Bar

to toggle to the desired port.

3. Press the

Return

key.

9F426-03 Module Speciﬁc Information

The Ring Map

The Ring Map shows a series of addresses in upstream/downstream order. These

addresses, which represent each FDDI device attached to the ring, are arranged

on the screen to simulate the circular fashion of a ring. When ﬁrst displayed, the

station at the upper left corner of this map is your current station. The screen

displays node class, node address, and twisted and/or wrapped conditions (T for

twisted, W for wrapped). The node class possibilities are:

• NAS (Null Attached Station) - Isolated station; station not connected to an

FDDI ring.

• DAS (Dual Attached Station) - Station that does not support M ports, but

connects directly to an FDDI primary and secondary ring using A and B ports.

• DAC (Dual Attached Concentrator) - Station that supports M ports and

connects directly to an FDDI primary and secondary ring using A and B ports.

• SAS (Single Attached Station) - Station that accesses the main ring through a

concentrator, creating a ring of trees topology.

• SAC (Single Attached Concentrator) - Station that accesses the main ring

through another concentrator and, in turn, allows the connection of more

devices. SACs provide the same connections as DACs, without attaching to the

dual ring.

• NAC (Null Attached Concentrator) - Isolated concentrator; concentrator not

connected to an FDDI ring.

While the map is updated, for example, during a ring topology change, the screen

may show ??:??:??:??:??:?? to illustrate an undetermined address.

Displaying the Ring Map Node Screen

To display the Ring Map Node Screen (from the Ring Map Conﬁguration Screen),

use the arrow keys to highlight an address, then press the Return key. The Ring

Map Node Screen appears.

The Ring Map display stops at the ﬁrst occurrence of an undetermined address,

and does not display any known information beyond this point.

NOTE

9F426-03 Module Speciﬁc Information

Ring Map Node Screen

The Ring Map Node Screen (Figure 2), displays speciﬁc information for a selected

FDDI node on the Ring Map.

Figure 2. Ring Map Node Screen

SmartSwitch 9000 Local Management

Ring Map Node

Module Name: 9F426-03 Firmware Revision: 01.04.10

Slot Number: 11 BOOTPROM Revision: 01.02.00

SELECTED NODE

Address: 00:00:B8:00:10:62

Upstream Address: NO UPSTREAM ADDRESS

Node Class: NAS

Mac Count: 0

Non-Master Count: 0

Master Count: 0

Peer Wrap: No

Unattached Conc: No

Twisted A-A: No

Twisted B-B: No

Synchronous Service: No

Rooted: No

EXIT RETURN

9F426-03 Module Speciﬁc Information

Ring Map Node Screen Fields

The following information brieﬂy explains each Ring Map Node Screen ﬁeld.

Address

Displays the address of the selected node.

Upstream Address

Displays the address of the selected node’s nearest upstream neighbor.

Node Class

Displays the class (NAS, DAS, DAC, SAS, or SAC) of the selected node. For an

explanation of these class codes, see page 5.

MAC Count

Displays the number of MACs (Media Access Controllers) that are attached to the

speciﬁed ring.

Non-Master Count

Displays the number of A and B ports on the selected node.

Master Count

Displays the number of M ports controlled by the selected node.

Peer Wrap

Indicates whether a wrap condition exists on a port. A peer wrap does not occur

when the A or B port is attached to an M port.

Unattached Conc (DAC only)

Indicates whether the selected node has no active A or B port.

Twisted A-A

Indicates whether the A port is connected to another A port.

Twisted B-B

Indicates whether the B port is connected to another B port.

Synchronous Service

Indicates whether the selected node uses synchronous bandwidth which

guarantees a certain percentage of the total FDDI bandwidth for real-time

applications.

Rooted

Indicates whether the selected node has an active A or B port when one, and only

one, end of the ﬁber link connects to an M port.

9F426-03 Module Speciﬁc Information

Switch Conﬁguration Screen

The Switch Conﬁguration Screen (Figure 3), displays parameters you can

conﬁgure to make the switch operational.

Figure 3. Switch Conﬁguration Screen

SmartSwitch 9000 Local Management

Switch Configuration

Module Name: 9F426-03 Firmware Revision: 01.04.10

Slot Number: 9 BOOTPROM Revision: 01.02.00

Switch Address: 00-00-1D-00-08-45 Type of STA: [NONE]

Numbers of Ports: 4

Port # MAC Address State Status

1 00-00-1D-00-08-45 disabled [DISABLED]

2 00-00-1D-00-08-46 forwarding [ENABLED]

3 00-00-1D-00-08-47 forwarding [ENABLED]

4 00-00-1D-00-08-48 forwarding [ENABLED]

SAVE EXIT RETURN

Port # refers to the following:

• Port 1 - INB

• Port 2 - Front Panel Port 1

• Port 3 - Front Panel Port 2

NOTE

Altri manuali per 9F426-03

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Cabletron Systems Interruttore

Cabletron Systems

Cabletron Systems MMAC-Plus 9H423-28 Manuale

Cabletron Systems

Cabletron Systems SmartStack STS16-20R Manuale utente

Cabletron Systems

Cabletron Systems SmartSwitch 9000 Documento tecnico

Cabletron Systems

Cabletron Systems MRXI 10BASE-T Manuale utente

Cabletron Systems

Cabletron Systems SmartSTACK EPIM1000-S1LX 1000BASE-LX Manuale utente

Cabletron Systems

Cabletron Systems MMAC-Plus 9H421-12 Manuale

Cabletron Systems

Cabletron Systems SEHI SEHI100TX- Manuale utente

Cabletron Systems

Cabletron Systems FN100 Manuale utente

Cabletron Systems

Cabletron Systems SPECTRUM 1800 Manuale utente

Cabletron Systems

Cabletron Systems HubSTACK SEHI-34 Manuale utente

Cabletron Systems

Cabletron Systems SEH100TX-22 Manuale utente

Cabletron Systems

Cabletron Systems SEH-24 Manuale utente

Cabletron Systems

Cabletron Systems ATX Manuale utente

Cabletron Systems

Cabletron Systems 9E106-06 Manuale utente

Cabletron Systems

Cabletron Systems STHI Manuale utente

Cabletron Systems

Cabletron Systems 9A656-04 Manuale utente

Cabletron Systems

Cabletron Systems MicroMMAC-24E Manuale utente

Cabletron Systems

Cabletron Systems BRIM-A6 Manuale utente

Cabletron Systems

Cabletron Systems 924TX Istruzioni operative e di manutenzione

Cabletron Systems

Cabletron Systems SmartSwitch 2H22 Manuale del proprietario

Cabletron Systems

Cabletron Systems Cabletron CyberSWITCH CSX5500 Manuale di istruzioni

Cabletron Systems

Cabletron Systems 3T02-04 Manuale utente

Cabletron Systems

Cabletron Systems MICROMMAC-22T Manuale utente

Cabletron Systems

Cabletron Systems SmartSwitch 9000 Manuale utente

Manuali Interruttore popolari di altre marche

URC

URC Total Control MFS-8 Manuale utente

Azbil

Azbil HPQ-D11 Manuale utente

Sony

Sony DFS-900M Manuale utente

SICK

SICK i17S Manuale utente

F&F

F&F SZR-277 Manuale utente

Shure

Shure UAMS/BK Manuale utente

Dräger

Dräger X-zone Switch Off Manuale utente

Asco

Asco Joucomatic 349 Series Manuale utente

BT Mini Hub Manuale utente

D-Link

D-Link DES-1226G Manuale utente

Johnson Controls

Johnson Controls FS80-C Manuale utente

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manuale utente

MicroNet

MicroNet SP1200A Manuale utente

Ruijie

Ruijie RG-PF2920 Series Manuale di installazione e funzionamento

Altinex

Altinex DA1914SX Manuale utente

MiLAN

MiLAN MIL-SM2401M Manuale utente

RJM

RJM MASTERMIND PBC/6X Manuale utente

Atlas

Atlas MMK-KVM8 Manuale utente