CalDigit Super Share Manuale utente
Quick Start Guide
For more information, visit www.caldigit.com
Apple, Apple Logo, Mac, the Mac logo and Macintosh are trademarks of Apple Inc.
Microsoft, Windows and Windows Logos are registered trademarks of the Microsoft Corporation.
All other trademarks are the property of their respective owners.
*Specications and package contents are subject to change without notice.
Fast, Reliable and Secure Storage Solutions
Contents
Introduction
General Use Warnings
Safety Warnings
Package Contents
Installing SuperShare
Installing HDPro2 or HDPro-24 Storage
Installing SuperShare Host Adapter Card
Installing Optical Cable
Installing PCIe Cable
Power On
Shutting Down
Accessories and Parts
Technical Support & Warranty Information
Technical Support
CalDigit Warranty Information
4
4
4
5
6
6
6
8
9
10
10
11
12
12
12
03
Introduction
Thank you for choosing the CalDigit SuperShare, please use the following quick installation
instructions to setup your SuperShare Switch & Hub.
General Use Warnings
Please read the SuperShare manual thoroughly and become familiar with the product
before use.
Only use the CalDigit SuperShare in an area with cool ventilation. Make sure that the fans
are not obstructed to ensure heat dissipation. Do not leave or use the SuperShare near a
heat source such as a heater or direct sunlight.
Avoid using the SuperShare in extremely hot and cold environments as it will increase
the likelihood of premature failure. A safe temperature range is between 40F – 95F.
Avoid using the SuperShare in humid environments. Moisture and condensation can
accumulate and damage the electrical components, resulting in unit failure.
Only use the power adapter that has been supplied with the CalDigit SuperShare. An
excessive or inadequate power supply can result in unstable performance or failure.
Safety Warnings
Keep SuperShare away from liquids and moisture. Direct application of liquids on
SuperShare can result in electric shock, re hazard and damage the unit. If your
SuperShare gets wet while it is still o, do not turn it on.
Do not tamper with or try to repair SuperShare unless you are a certied CalDigit
technician. Doing so can result in personal injury and damage SuperShare. This will also
void your warranty. If you have any issues, contact CalDigit Technical Support.
04
Package Contents:
(One) CalDigit SuperShare Switch. (6-Port or 12-Port)
(One) CalDigit SuperShare Hub. (7-Port)
(Four) Optical Cable. (10M, 30M, 50M or 100M)
(One) PCIe (8-lane) cable.
(Four) SuperShare Host Adapter Card.
(Two) Rack mounting kits. One for Switch, One for Hub.
(One) CalDigit SuperShare CD
(Two) Power supply kit.
Please contact your CalDigit reseller for any faulty or missing parts.
1
2
3
4
5
6
7
8
05
Installing SuperShare
Installing HDPro2 or HDPro-24 Storage
Please refer to the HDPro2 or HDPro-24 installation procedure or manual. Manuals can be
downloaded from www.caldigit.com/support.asp.
Installing SuperShare Host Adapter Card
Turn o your computer and unplug the AC power cord from the wall or power bar.
Please make sure the computer is turned o. Unplug the power cord and wait 5 to 10
minutes allowing he computer’s internal components to cool.
Remove cover from computer.
Power Cord Socket
Power Cord Plug
1
2
06
Locate available PCIe slot on motherboard.
Always put the PCI card in Slot #3 or Slot #4 to obtain optimal performance.
Hold the PCIe card mrly by the ouside edge, push it into the slot making sure the PCI
connectiins t outside the computer.
3
4
5
07
Installing Optical Cable
Attach the Optical cable to SuperShare Host Adapter Card.
Attach the other side of Optical cable to SuperShare Switch.
1
2
08
PCIe 8x Cable
SuperShare Hub
To Storage (PCIe)
Installing PCIe Cable
Attacah the PCIe (x8) cable to SuperShare Switch. (Port-A)
Attacah the other side of PCIe cable (x8) to SuperShare Hub. (Port-1)
Attach all the PCIe cables from the Storage, HDPro2 or HDPro-24, to SuperShare Hub.
(Port-3 to Port 9)
Installing RAIDShield and Driver to all workstations
Insert the provided CD into the computer DVD/CD drive or visit
www.caldigit.com/support.asp.
Go to "Mac Installer" Folder or "Windows Installer" Folder.
Launch SuperShare Installer.
When installation is complete, shutdown the computers.
PCIe 8x Cable
SuperShare Switch
1
2
3
1
2
3
4
To Workstations (optical)
09
Power
Power On
To power on the SuperShare SAN, please follow the steps:
Power on all HDPro2s or HDPro-24s.
Wait 5 seconds.
Power on SuperShare Hub.
Wait 5 seconds.
Power on SuperShare Switch.
Wait for three beeps from the Switch, this may take up to 2 minutes.
Power on all workstations.
Shutting Down
When you want to shut down your the SuperShare SAN, please follow the steps:
Shutdown all your workstations.
Power o SuperShare Switch.
Power o SuperShare Hub.
Power o all HDPro2s.
1
2
3
4
5
6
7
1
2
3
4
10
Indice
Altri manuali CalDigit Interruttore
