Campbell CELL200-Series Manuale utente

4G LTE Cellular Module

For Public Static IP Addresses

Part Number 35035

Revision: 02/2019

www.campbellsci.com/cellular-communications

1. Introduction

NOTE:

This Quick Deploy Guide is a general reference to give the

installer an overview of the steps required to make this

system operational. The Product Manual is the definitive

source for detailed installation instructions and

information.

For best results, update to the latest data logger

operating system and version of Device Configuration

Utility.

NOTE:

CR3000, CR1000 and CR800-series users must refer to the

CELL200 Product Manual. This Quick Deploy Guide does

not apply.

You should have received two Quick Deploy Guides with your

CELL200-series module. The one you follow will depend on

whether your module was configured with a private dynamic

or public static IP address.

The Provisioning Report received with your Cellular Data

Service shows whether the module was configured with a

private dynamic or public static IP address. See FIGURE 1-1 (p.

1) for an example of a Campbell Scientific Provisioning Report.

Other cellular providers should provide similar information.

USE THIS GUIDE if your module has a public static IP address.

FIGURE 1-1. Static IP provisioning report

Additionally, Campbell Scientific cellular modules configured

with a public static IP address will have two stickers on the

module, as shown in FIGURE 1-2 (p. 1). One sticker will show the

module phone number and data plan. The second sticker will

show the static IP address. USE THIS GUIDE.

Campbell Scientific cellular modules configured with a private

dynamic IP address will have one sticker on the module. It will

show the module phone number and data plan. USE THE

OTHER GUIDE.

FIGURE 1-2. Module with public static IP address

2. Campbell Scientific cellular data

service

Campbell Scientific can provide subscriptions to cellular

service through Verizon, AT&T, T-Mobile, Vodafone, Telstra,

and over 600 other providers worldwide. When this cellular

service is purchased with the module, the module will come

pre-provisioned with the required SIM card and APN. If you

have already purchased the CELL200 series, call Campbell

Scientific to set up service.

3. Install the SIM card

NOTE:

If you purchased cellular service from Campbell Scientific

with the module, it will come with the SIM (Subscriber

Identity Module) card already installed.

1. Remove the SIM card cover.

2. Note the location of the notched corner for correct

alignment. The gold contact points of the SIM face

down when inserting the SIM card as shown in FIGURE

3-1 (p. 2). Gently slide the card into the slot until it stops

and locks into place. To eject the SIM card, press it in

slightly and release.

3. Replace the SIM card cover.

FIGURE 3-1. SIM card installation

4. Modules using a public static IP

4.1 Set up hardware

1. Connect the Cellular antenna.

2. Connect your data logger to the CELL200-series

module RS-232 or CS I/O port.

3. If not connecting through CS I/O, provide power to the

CELL200 series.

4.2 Configure data logger

1. Connect to your data logger by using Device

Configuration Utility.

2. On the PPP tab, set Config/Port Used to CS I/O SDC8 or

RS-232, depending on how you are connected to the

data logger.

3. Verify the Modem Dial String setting is blank.

4. If connecting through RS-232, on the Comport Settings

tab, set RS232 BaudRate to 115200 Fixed.

5. On the Cellular tab, enter the APN provided by your

cellular provider.

6. Click Apply to save the changes.

4.3 Set up LoggerNet

1. Select Add Root >IPPort.

2. Select PakBusPort

3. Add a data logger to the PakBusPort.

4. Select the IPPort in the Network Map. Enter the CELL200

series IP address and port number. The IP address and

port number are input in the Internet IP Address field

separated by a colon. Preceding zeros are not entered

in the Internet IP Address (for example, 070.218.074.247

is entered as 70.218.74.247). The default port number is

6785.

5. For PakBus data loggers, leave the default settings for

the PakBusPort. PakBus Port Always Open should not be

checked. If used, enter the TCP Password.

6. For PakBus data loggers, select the data logger in the

Network Map and set the PakBus Address to match that

of the data logger (default address in the data logger is

1). Click Apply to save the changes.

4.4 Test the connection

Use the Connect screen to test the connection. Click on the

appropriate station and click Connect to initiate a call to the

data logger.

TIP:

The connection time is subject to many external factors. It

is often less than 30 seconds but could be up to fifteen

minutes. Be patient.

If the call is successful, the connectors at the bottom of the

screen will come together and clock information from the data

logger will be displayed in the Station Date/Time field.

Altri manuali Campbell Unità di controllo

Campbell

Campbell SDM-AO4A Manuale utente

Campbell

Campbell CR300 series Istruzioni per l'installazione e il funzionamento

Campbell

Campbell SDM-SI01A Manuale utente

Campbell

Campbell SDM-SIO1A Manuale utente

Campbell

Campbell CompactFlash CFM100 Manuale utente

Campbell

Campbell CELL200 Series Manuale utente

Campbell

Campbell TEMP 120 Manuale utente

Campbell

Campbell CDM-A100 Series Manuale utente

Campbell

Campbell NL116 Manuale utente

Campbell

Campbell CompactFlash CFM100 Manuale utente

Campbell

Campbell SDM-CD16 Manuale utente

Campbell

Campbell CELL200 Series Manuale utente

Campbell

Campbell CURS100 Manuale utente

Campbell

Campbell LLAC4 Manuale utente

Campbell

Campbell SDM-SIO1A Manuale utente

Campbell

Campbell SDM-CD16D Manuale utente

Campbell

Campbell CELL205 Manuale utente

Campbell

Campbell CS240 Manuale utente

Campbell

Campbell CELL200 Series Manuale utente

Campbell

Campbell CR10 PROM Manuale utente

Campbell

Campbell GRANITE VOLT Series Manuale utente

Campbell

Campbell SDM-IO16 Manuale utente

Manuali Unità di controllo popolari di altre marche

Festo

Festo Compact Performance CP-FB6-E Manuale elenco delle parti

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuale utente

JS Automation

JS Automation MPC3034A Manuale utente

JAUDT

JAUDT SW GII 6406 Series Guida rapida

Spektrum

Spektrum Air Module System Manuale utente

BOC Edwards

BOC Edwards Q Series Manuale utente

KHADAS

KHADAS BT Magic Manuale utente

Etherma

Etherma eNEXHO-IL Manuale utente

PMFoundations

PMFoundations Attenuverter Manuale utente

GEA

GEA VARIVENT Manuale utente

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuale utente

Altronix

Altronix LINQ8PD Istruzioni per il montaggio

Eaton

Eaton Powerware Series Manuale utente

WAGO

WAGO 750-407/040-000 Manuale utente

Sony

Sony CCU-590 Manuale utente

Graco

Graco 25D614 Manuale utente

Task Force Tips

Task Force Tips YE-RF-900 Manuale di programmazione

Shini

Shini SPV-U Series Manuale utente