Casablanca W-18 Manuale utente
Casablanca Fan Co. • Factory Service Department • Technical Library
W-28
Attractive dual slide optional fan and light
control.
Noise-freecircuitryandquietoperation
Fouroptional fan speed settings
Continuouslyvariablelightdimming(300
watt max)
120VAC,50/60Hz, 1.5Amp rating
Requiresspecialwiring(athirdwire)
Will operate one fan only
AvailableinSnowWhiteandIvory
finishes
CAUTION! Failure to set the pull-chain speed to HIGH can result in faulty
operation of the fan and damage to the wall control. To confirm fan is set to
HIGH: Turn W-80 fan speed switch to ‘HI’- set fastest fan speed with pull chain.
3-SPEED © OPTIONAL WALL CONTROL © W-28 / W-18
W-28
W-18
W-28
W-28 CEILING FAN/LIGHT CONTROL
OPERATION
1. Raise the fan slider to increase fan speed, lower
todecrease.
2. For the fan, three speeds are available: Low 1,
Low 2, Medium, and High.The bottom position is
OFF.
3. The light slider is a dimmer, the bottom is OFF,
raise to increase intensity of the light.
4. The toggle switch is a separate preset control—
turns both the fan and light off or on to the
currentsetting.
Casablanca Fan Co. • Factory Service Department • Technical Library
The fan may be turned ON and OFF by the W-28 wall control.
The lights may be turned ON and OFF by the W-28 and the intensity adjusted from low to high.
The fan must be supplied with two independent 120V AC supply wires.
Set the FAN pull chain switch to the HIGH speed setting.
Turn the lights ON at the fan.
The W-28 allows the choice of four (3) different speed settings.
CAUTION! Failure to set the pullchain speed to HIGH can result in faulty
operation of the fan and damage to the W-28 wall control. To confirm fan is
set to HIGH: Turn W-28 fan speed switch to ‘HI’- set fastest fan speed with pull
chain.
IMPORTANT NOTE: The fan
must be supplied with three
independent 120V AC supply
wires to provide power for the
fan, the light, and neutral.
Installation is to be in
accordance with all
National Electrical Code
and local codes
WARING: DONOT use these wiring diagram
when wiring W-8 or W-80 wall controls. This
will cause damage to both the PC Board and
Wall Control
Casablanca Fan Co. • Factory Service Department • Technical Library
The fan may be turned ON and OFF by the W-28 wall control.
The lights may be turned ON and OFF by the W-28 and the intensity adjusted from low to high.
The fan must be supplied with two independent 120V AC supply wires.
Set the FAN pull chain switch to the HIGH speed setting.
Turn the lights ON at the fan.
The W-28 allows the choice of four (3) different speed settings.
CAUTION! Failure to set the pullchain speed to HIGH can result in faulty
operation of the fan and damage to the W-28 wall control. To confirm fan is
set to HIGH: Turn W-28 fan speed switch to ‘HI’- set fastest fan speed with pull
chain.
IMPORTANT NOTE: The fan
must be supplied with three
independent 120V AC supply
wires to provide power for the
fan, the light, and neutral.
Installation is to be in
accordance with all
National Electrical Code
and local codes
WARING: DONOT use this wiring diagram
when wiring W-8 or W-80 wall controls. This
will cause damage to both the PC Board and
Wall Control
Casablanca Fan Co. • Factory Service Department • Technical Library
INSTALLATION OFWALLCONTROL
CAUTION! To avoid overheating and possible
damage to other equipment, do not install to
control receptacle, fluorescent lighting
fixture, motor-operated appliance, or
transformersupplied appliance.
NOTE: W-28 is used to describe either Almond (-A) or
White (-W) finish.
The W-28 is designed to replace a standard wall switch
and will fit wall boxes (metal or plastic) with a depth of 2”
or greater.
Notforusewith fansthat useone pullchainswitch
to control both fan and light.
CAUTION: Ensure power is turned OFF
at the breaker or fuse panel before
starting installation.
1. Remove the screws and switch plate from the existing
switch box.
2. Remove the screws holding the switch in the switch
box.
3. Pull the existing switch from the switch box to expose
the wire connections.
4. Remove the two wires from the switch.
5. Wiring preparation, if required:
Strip wires:
• 3/8” for 14 guage
• 1/2” for 16 and 18 guage
NOTE: The wire connectors provided are suitable for
copper wire only. Use to join the following wire
combinations: One No. 14 guage with one No. 16 or 18
guage.
6. Connect black lead of control to 120V AC hot wire.
Connect the red lead to the light circuit controlled by
slider on right side of unit. Connect yellow lead to fan
motor(s) wire. The fan speed will be controlled by the
left slider on the unit. If unit is used to control only one
light circuit,
place wire connector on unused lead. Secure these
connections with the wire connectors.
7. If a ground wire is provided in your electrical
box, attach it to the ground screw near the
bottom of the mounting plate.
8. Install the W-28 in the wall box with the two
long screws provided.
CAUTION: Be sure no wires are pinched!
9. Install the wall plate with the two color matched
screws.
10.Turn on power to test the controller.
Installation is to be in accordance with all
National Electrical Code and local codes
WARING: DONOT use this wiring diagram
when wiring W-8 or W-80 wall controls. This
will cause damage to both the PC Board and
Wall Control
Questo manuale è adatto per i seguenti modelli
1
Indice
Altri manuali Casablanca Unità di controllo
Manuali Unità di controllo popolari di altre marche
Festo
Festo Compact Performance CP-FB6-E Manuale elenco delle parti
Elo TouchSystems
Elo TouchSystems DMS-SA19P-EXTME Manuale utente
JS Automation
JS Automation MPC3034A Manuale utente
JAUDT
JAUDT SW GII 6406 Series Guida rapida
Spektrum
Spektrum Air Module System Manuale utente
BOC Edwards
BOC Edwards Q Series Manuale utente
