CDA EXA60 Guida rapida

www.cda.eu

EXA60 & EXA80

Extractors

Installation, use and maintenance

Contents:

3 Important

4 Important information

6 Using your extractor

7 Care and maintenance

7 Removing the grease ﬁlter

8 Changing/ﬁtting the charcoal ﬁlter(s)

9 Changing the light

10 - 17 Installation

10 Installation preparation - height

12 Ducting and ventilation

14 Mounting the extractor

16 Alternative to the chimney sections

16 Using the ‘T-piece’ for recirculation

17 Securing the chimney sections

18 Mains electricity connection

20 Electrical information

21 Troubleshooting

23 Energy Eciency Information

Important

The CDA Group Ltd cannot be held responsible for injuries or losses

caused by incorrect use or installation of this product. Please note that

CDA reserve the right to invalidate the guarantee supplied with this

product following incorrect installation or misuse of the appliance or

use in a commercial environment.

This appliance is not designed to be used by people (including

children) with reduced physical, sensorial or mental capacity, or

who lack experience or knowledge about it, unless they have had

supervision or instructions on how to use the appliance by someone

who is responsible for their safety.

Under no circumstances should any external covers be removed for

servicing or maintenance except by suitably qualiﬁed personnel.

Appliance information:

Please enter the details on the appliance rating plate below for

reference, to assist CDA Customer Care in the event of a fault with

your appliance and to register your appliance for guarantee purposes.

Appliance Model

Serial Number

EU Declarations of Conformity:

This appliance has been designed, constructed and marketed in

compliance with safety requirements of EU Directive 2014/35/EU (LVD)

and requirements of EU Directive 2014/30/EU (EMC).

IMPORTANT INFORMATION FOR CORRECT DISPOSAL OF THE

PRODUCT IN ACCORDANCE WITH EC DIRECTIVE 2012/19/EU.

At the end of its working life, the product must be taken to a special

local authority waste collection centre or to a dealer providing

appliance recycling services.

Disposing of a household appliance separately avoids possible

negative consequences for the environment and health. It also

enables the constituent materials to be recovered, saving both energy

and resources. As a reminder of the need to dispose of household

appliances separately, the product is marked with a crossed-out

wheeled dustbin.

Please note:

•Under no circumstances should the extractor be connected to any

gas ventilation system, ﬂue system or hot air ducting system.

• Do not vent the extractor into an attic or loft space.

•Only house the extractor in rooms with adequate ventilation.

Remember that the extractor is powerful and whatever air is

extracted needs to be replaced.

•Do not tile the extractor in. It should be removable for service or

maintenance.

•Do not use silicone sealant to secure the hood to the wall.

•You must be able to isolate the extractor from the mains electrical

supply after installation.

•This extractor has been designed to be used in a room with a

volume of less than 36m.

•Steam cleaners must not be used when cleaning this appliance.

•The performance of your extractor will vary depending on a number

of factors. These include: type of extraction, length of ducting, room

volume, ventilation available and cleanliness of the ﬁlters.

Using your extractor

For best performance, you should switch on the extractor 15 minutes

before starting to cook and leave it to run for approximately 15

minutes after the end of cooking.

Control Panel (Fig. 1)

A - Light key B - Speed decrease key C - Speed increase key

D - Timer key

To switch the extractor light on or o

• Press the light key (A).

To switch on the extractor or to change the speed

• Press the speed increase key to switch the unit on. Adjust the

speed as necessary using keys B and C. The circular indicators will

illuminate progressively for the ﬁrst, second, third or intensive speed

levels to indicate which is active.

• Press the timer key (D) to activate a 10 minute timer for that speed.

The selected speed’s indicator should ﬂash whilst the timer is

active. Touch the same sensor to cancel the timer. Please note that

the intensive speed automatically switches to speed 3 after 6

minutes (see page 21 for more information).

To switch the extractor o

• Use the speed decrease key until no speed indicators are on.

A B DC

Fig. 1

Care and maintenance

IMPORTANT: DO NOT PERFORM MAINTENANCE OR CLEANING

OF THE EXTRACTOR WITHOUT FIRST SWITCHING OFF THE

ELECTRICITY SUPPLY.

Cleaning

You should use a non-abrasive cleaner. Any abrasive cleaner

(including Cif) will scratch the surface and could erase the control

panel markings.

You can clean your extractor eectively by simply using a dilute

solution of water and mild detergent and drying to a shine with a

clean cloth.

IMPORTANT:

Always protect surfaces immediately beneath the extractor (such

as a hob) with clean, dry towels or similar cushioning items before

carrying out any cleaning or maintenance in case of falling parts/

items.

Removing and cleaning the grease ﬁlter

The grease ﬁlter should be kept clean to minimise the risk of ﬁre.

At least once a month you should remove and clean the grease

ﬁlter with hot soapy water. You can also wash the grease ﬁlter in a

dishwasher, ensuring that you place it in an upright position to prevent

damage from other items in the dishwasher. After rinsing and drying,

replace the ﬁlter. Cleaning the grease ﬁlter in the dishwasher may

lead to discolouration. This is normal and does not constitute a

fault with the appliance.

Please note: After 30 hours of usage all speed indicators will ﬂash to

signal that the ﬁlter needs to be cleaned. Press the timer key to reset

after cleaning.

To remove the grease ﬁlter, lift open the extractor cover and then

release the catch on the handle on the grease ﬁlter. It will release at

the handle side. Lift it towards you slightly and then lower the grease

ﬁlter to remove it completely. To replace the grease ﬁlter, repeat the

steps in reverse.

Changing the charcoal ﬁlter (re-circulating only) - Fig. 2

To ensure best performance of your extractor, you should replace the

charcoal ﬁlter every four to six months, depending on use. To attach a

new charcoal ﬁlter, ﬁrst remove the grease ﬁlter as described above.

Remove any old charcoal ﬁlters that are in place. Take a new charcoal

ﬁlter and ﬁt it into position behind where the grease ﬁlter sits. Use

the structural screws in the ﬁlter aperture to hold the charcoal ﬁlter in

place. Repeat this process with the remaining side and then re-ﬁt the

grease ﬁlter.

Fig. 2

Changing the light

This appliance is ﬁtted with energy saving LED lighting that has a

considerably longer life expectancy than traditional ﬁlament bulbs.

These are not user-replaceable. In the unlikely event of a failure

please contact CDA Customer Care using the details on page 22.

Do not touch bulbs or adjacent areas during or straight after

prolonged use of the lights.

The light is designed for use during cooking and not for general room

illumination.

Extended use of the light can reduce the life span.

Installation

When installing this product we recommend you seek the help of

another individual. This product may have some sharp edges. Please

take care and wear adequate PPE when handling.

Installation preparation - height

When the extractor is to be installed above an electric hob, the

minimum distance between the hob and the bottom edge of the

extractor must exceed 495mm.

When the extractor is to be installed above a gas hob, the minimum

distance between the bottom edge of the extractor and hob must

exceed 495mm.

If the instructions provided with your gas hob state that the

required distance between the hob and extractor must be greater

than our measurement, then that is the distance that should be

observed; this is a legal requirement and may lead to your hob

being disconnected from the gas supply and the installation being

reported under RIDDOR (the height should be measured from the

top of the burners).

IN THE ABSENCE OF ANY INSTRUCTIONS SUPPLIED WITH THE

GAS HOB, THE MINIMUM DISTANCE BETWEEN THE HOB AND

EXTRACTOR MUST BE AT LEAST 760mm. The width of any hob

must not be greater than the width of the extractor installed above

it.

Questo manuale è adatto per i seguenti modelli

Indice

Manuali Scrubber popolari di altre marche

Olympus

Olympus M200H Manuale utente

Clarke

Clarke BEXT 100H Manuale di installazione e funzionamento

JOHNY VAC

JOHNY VAC JVC70BCT Manuale utente

RCm

RCm Elan Series Manuale

Kärcher

Kärcher B 120 W Manuale utente

Truvox

Truvox Orbis MotorScrubber 20 Manuale utente

Numatic

Numatic TTB 4045/100 Manuale utente

U.S. Products

U.S. Products PEX 500-C-TICK Istruzioni operative

Mclennan

Mclennan C510 Manuale utente

Tennant

Tennant T20 LPG Manuale utente

Columbus

Columbus ARA 66 BM 100 Manuale utente

Numatic

Numatic TTV 678G / 300T Manuale utente

American-Lincoln

American-Lincoln 505-945 Manuale utente

FIORENTINI

FIORENTINI ET 65-75 Manuale utente

Floorpul

Floorpul ruby 48 blt Guida utente

Onyx

Onyx RX-34 Manuale utente

Dustbane

Dustbane Hurricane 400 Manuale utente

Sana

Sana EUJ-702 Manuale utente