Central Pneumatic 93048 Manuale utente

Air Pin Stripe Removal Kit

ASSEMBLY AND OPERATING INSTRUCTIONS

3491 Mission Oaks Blvd., Camarillo, CA 93011

Visit our Web site at http://www.harborfreight.com

manual or any artwork contained herein may be reproduced in any shape or form

without the express written consent of Harbor Freight Tools.

For technical questions and replacement parts, please call 1-800-444-3353

93048

SKU 93048 For technical questions and replacement parts, please call 1-800-444-3353 Page 2

Speciﬁcations

Construction: Cast Aluminum with

Steel Parts Eraser Pads:

(4) 3-1/2” Dia. x 5/8”

Thick Soft Rubber

Pads

Air Inlet: 1/4” - 18 NPT Operating Pressure: 90 PSI

Average Air

Consumption: 4.5 CFM No Load RPM: 3100 RPM

Regulator: Internal Air Regulator Spindle Threads: 5/16” x 24

Dimensions: 8-1/2”L x 2” Diameter Net Weight: 3.08 LBS.

IMPORTANT: This tool may cause damage to materials or paints that soften when exposed to the

heat generated during use (such as acrylic lacquers). For this reason, we strongly recommend that

it not be used on these types of materials.

Save This Manual

You will need the manual for the safety warnings and precautions, assembly

instructions, operating and maintenance procedures, parts list and diagram. Keep

your invoice with this manual. Write the invoice number on the inside of the front

cover. Keep the manual and invoice in a safe and dry place for future reference.

Safety Warnings and Precautions

WARNING: When using tool, basic safety precautions should always be fol-

lowed to reduce the risk of personal injury and damage to equipment.

Read all instructions before using this tool!

1. Keep work area clean. Cluttered areas invite injuries.

2. Observe work area conditions. Do not use machines or power tools in

damp or wet locations. Don’t expose to rain. Keep work area well lit. Do not

use electrically powered tools in the presence of ﬂammable gases or liquids.

3. Keep children away. Children must never be allowed in the work area. Do

not let them handle machines, tools, or extension cords.

4. Store idle equipment. When not in use, tools must be stored in a dry

location to inhibit rust. Always lock up tools and keep out of reach of

children.

5. Use the right tool for the job. Do not attempt to force a small tool or

REV 05i

SKU 93048 For technical questions and replacement parts, please call 1-800-444-3353 Page 3

attachment to do the work of a larger industrial tool. There are certain

applications for which this tool was designed. It will do the job better and

more safely at the rate for which it was intended. Do not modify this tool and

do not use this tool for a purpose for which it was not intended.

6. Dress properly while working. Protect your skin from accidental abrasion

burns by wearing long sleeves and safety gloves. Do not wear loose clothing

or jewelry as they can be caught in moving parts. Protective, electrically

nonconductive clothes and nonskid footwear are recommended when

working. Wear restrictive hair covering to contain long hair.

7. Use eye and ear protection. Always wear ANSI approved impact safety

goggles, full face shield, and ear protection when using this tool. Wear an

ANSI approved dust mask or respirator when working around metal, wood, and

chemical dusts and mists.

8. Do not overreach. Keep proper footing and balance at all times. Do not

reach over or across running machines.

9. Maintain tools with care. Keep tools clean and in good condition for better

and safer performance. Follow instructions for lubricating and changing

accessories. Inspect tool ﬁttings and hoses periodically and, if damaged,

have them repaired by an authorized technician. The handles must be kept

clean, dry, and free from oil and grease at all times.

10. Disconnect power. Disconnect from air pressure source when not in use.

11. Remove adjusting keys and wrenches. Check that keys and adjusting

wrenches are removed from the work surface before connecting it.

12. Avoid unintentional starting. Be sure the throttle lever is in the Off position

when not in use and before attaching to pressure source. Do not carry

any tool with your hand on the throttle lever, whether it is attached or not.

Disconnect the air hose from the tool when not in use.

13. Stay alert. Do not operate any tool when you are tired.

14. Check for damaged parts. Before using any tool, any part that appears

damaged should be carefully checked to determine that it will operate

properly and perform its intended function. Check for alignment and binding

of moving parts; any broken parts or mounting ﬁxtures; and any other

condition that may affect proper operation. Any part that is damaged should

be properly repaired or replaced by a qualiﬁed technician. Do not use the

tool if the throttle lever does not function properly.

15. Guard against electric shock when working on electrical equipment,

such as your air compressor. Prevent body contact with grounded

surfaces such as pipes, radiators, ranges, and refrigerator enclosures.

SKU 93048 For technical questions and replacement parts, please call 1-800-444-3353 Page 4

16. Replacement parts and accessories. When servicing, use only identical

replacement parts. Use of any other parts will void the warranty. Only use

accessories intended for use with this tool. Approved accessories are

available from Harbor Freight Tools.

17. Do not operate tool if under the inﬂuence of alcohol or drugs. Read

warning labels on prescriptions to determine if your judgment or reﬂexes are

impaired while taking drugs. If there is any doubt, do not operate the tool.

18. Use proper size and type air pressure line and ﬁttings. The

recommended air line should deliver no more than 90 PSI. Recommended

air inlet size is 1/4” - 18 NPT.

19. Maintenance. For your safety, service and maintenance should be

performed regularly by a qualiﬁed technician.

20. You should maintain a proper regulator and moisture trap in your air

line at all times.

21. WARNING: This product contains or, when used, produces a chemical

known to the State of California to cause cancer and birth defects or

other reproductive harm. (California Health & Safety Code § 25249.5,

et seq.)

Note: Performance of ool may vary depending on variations in local air pressure.

SPECIFIC SAFETY PRECAUTIONS

1. This tool may mar paint or damage nearby components of the vehicle, such

as mirrors, trim, etc. Use great caution with this tool. Always test this tool in a

hidden area of the vehicle before beginning work. If the tool causes damage

to the test area, do not use it in the main area.

2. Always wear ANSI approved face mask when using this tool. Bits of pad,

removed paint, etc. will be thrown from the tool at high speed when in use.

Never use without proper protection. Hold the tool ﬁrmly while in use.

3. Do not allow this tool to touch hands or other unprotected skin while in use.

Skin may be burned, torn or otherwise injured by this tool. Never set the tool

down until it has stopped turning. Disconnect the air supply when not in use

to prevent accidental starting.

4. WARNING: Replace pad when it is worn to approximately 2/3 its original

diameter. If you use pads below this point, they may tear off suddenly in use,

causing personal or property damage.

Warning:The warnings, cautions, and instructions discussed in this instruction

manual cannot cover all possible conditions and situations that may occur.

It must be understood by the operator that common sense and caution are

factors which cannot be built into this product, but must be supplied by the

operator.

REV 07f

SKU 93048 For technical questions and replacement parts, please call 1-800-444-3353 Page 5

Operation

1. Install a standard 1/4” Air Connector (not included) to the Air Inlet (1). First

wrap the threaded portion of the 1/4” air connector with pipe thread seal tape

before threading it into the Air Inlet (1). Tighten securely.

2. Attach a standard quick connector (not included) to your air pressure source

hose. Then attach the air hose to the Pin Stripe Remover.

NOTE: If you are not using an automatic inline oiler, add a few drops of

pneumatic oil to the Air Inlet (1) before attaching the air hose. Add a few

more drops of oil after every hour of continual use.

3. Set the air pressure regulator at 90 psi.

WARNING: DO NOT INCREASE THE AIR PRESSURE to the tool beyond 90

psi. This may damage the tool, or cause personal injury.

4. Check the air line and its connections for air leaks. Make note of these, and

repair them before using this tool.

NOTE: We recommend the use of inline ﬁlter, regulator, and oiler in any com-

pressed air system using tools purchased from Harbor Freight Tools. Please refer

to the schematic below for a suggested system set up. These components are not

included in this kit, but are available from Harbor Freight Tools.

Pin Stripe

Remover

CAUTION: Disconnect the air pressure

hose before changing pads or making

any adjustments to this tool. Severe

injury or property damage may other-

wise result.

5. To remove the Pad (36), remove the

Arbor (35), the washer and old Pad.

Do this by holding the Pad while

turning the Arbor (35) counterclock-

wise with the Arbor Wrench (38).

Installing an eraser pad

SKU 93048 For technical questions and replacement parts, please call 1-800-444-3353 Page 6

6. To install a new pad, place the new

pad onto the Arbor (35) followed by

the washer.The washer and end of

the Arbor (35) (shown in the picture

at right) are both designed to ﬁt into

the recesses of the pad.Tighten the

Arbor (35) by holding the Pad (36)

and turning the Arbor (35) clockwise

using the Arbor Wrench (38). The

Pad (36) is tightened in place as

the Arbor (35) is tightened in place

onto the tool.

IMPORTANT: This tool may cause

damage to materials or paints that soften when exposed to the heat

generated during use (such as acrylic lacquers). For this reason, we

strongly recommend that it not be used on these types of materials.

7. Turn ON the Pin Stripe Remover by squeezing the Throttle Lever (32). The

Pad (36) will begin to rotate. Allow the Pad to get up to full speed before

applying it to the work surface as needed to erase the pin stripe. Work

in a direction opposite to the rotational direction of the pad.

NOTE: This item can damage paint if used with excessive force; Harbor Freight

Tools cannot be held responsible for any damage resulting from misuse of

this tool. Check manufacturer’s information on the paint before using this

tool.

8. When you are done working, lift the pad from the work surface before

releasing the Throttle Lever (32). The Pad (36) will cease to rotate. Repeat

this process as needed. You may change pads as needed.

9. When you are done using this tool, turn off the air compressor, and

disconnect the air hose. Put the Pin Stripe Remover away in its proper

storage place.

an eraser pad

REV 05i

SKU 93048 For technical questions and replacement parts, please call 1-800-444-3353 Page 7

Parts List

NOTE: Some parts are listed and shown for illustration purposes only and are not available individually

as replacement parts. Some parts are available only as part of an assembly.

Part Description Qty. Part Description Qty.

1 Air Inlet 1 20 Ball Bearing 1

2 Inlet Bushing “O” Ring 1 21 Internal Gear 1

3 Exhaust Deﬂector 1 22 Clamp Nut 1

4 Motor Housing 1 23 Spring 1

5 Ball Bearing 1 24 Air Regulator 1

6 End Plate 1 25 “O” Ring 1

7 Pin 2 26 “O” Ring 1

8 Rotor 1 27 Valve Screw 1

9 Rotor Blade 4 28 “O” Ring 2

10 Rotor Collar 1 29 Throttle Valve 1

11 Cylinder 1 30 “O” Ring 2

12 Steel Ball 1 31 Valve Bushing 1

13 End Plate 1 32 Throttle Lever 1

14 Ball Bearing 1 33 Pin 1

15 Washer 1 34 Nut 1

16 (Not Used) 35 Arbor 1

17 Gear Case 1 36 Pad 1

18 Planet Gear 2 37 Grip 1

19 Pin 2 38 Arbor Wrench 1

Maintenance

1. Your Pin Stripe Remover should be kept clean, dry and protected from corrosion or

damage.

2. When not in use, store your tool out of the reach of children. Do not allow it to be

exposed to water, corrosive materials, or undue impact.

3. If you are not using an inline oiler, you should inject a few drops of pneumatic oil into

the air inlet of the tool after every hour of continuous use.

4. If your tool loses power, or you notice air leaks, take it to a certiﬁed technician for

service.

SKU 93048 For technical questions and replacement parts, please call 1-800-444-3353 Page 8

Assembly Drawing

PLEASE READ THE FOLLOWING CAREFULLY

THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS DIAGRAM

IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER NOR DIS-

TRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT

HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE

IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER

AND/OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS

SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS AND NOT BY THE

BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER RE-

PAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT

OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.

SKU 93048 For technical questions and replacement parts, please call 1-800-444-3353 Page 9

Limited 90-Day Warranty

Harbor Freight Tools Co. makes every effort to assure that its products meet high

quality and durability standards, and warrants to the original purchaser that this product is

free from defects in materials and workmanship for the period of 90 days from the date of

purchase.This warranty does not apply to damage due directly or indirectly, to misuse, abuse,

negligence or accidents, repairs or alterations outside our facilities, criminal activity, improper

installation, normal wear and tear, or to lack of maintenance. We shall in no event be liable

for death, injuries to persons or property, or for incidental, contingent, special or consequen-

tial damages arising from the use of our product. Some states do not allow the exclusion or

limitation of incidental or consequential damages, so the above limitation of exclusion may

not apply to you. THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRAN-

TIES, EXPRESS OR IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY

AND FITNESS.

To take advantage of this warranty, the product or part must be returned to us with

transportation charges prepaid. Proof of purchase date and an explanation of the complaint

must accompany the merchandise. If our inspection veriﬁes the defect, we will either repair or

replace the product at our election or we may elect to refund the purchase price if we cannot

readily and quickly provide you with a replacement. We will return repaired products at our

expense, but if we determine there is no defect, or that the defect resulted from causes not

within the scope of our warranty, then you must bear the cost of returning the product.

This warranty gives you speciﬁc legal rights and you may also have other rights

which vary from state to state.

3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • (800) 444-3353

Indice

Altri manuali Central Pneumatic Utensili elettrici

Central Pneumatic

Central Pneumatic 46446 Manuale utente

Central Pneumatic

Central Pneumatic 36567 Manuale utente

Central Pneumatic

Central Pneumatic 98898 Manuale di installazione

Central Pneumatic

Central Pneumatic 65902 Manuale di installazione

Central Pneumatic

Central Pneumatic Contractor 90399 Manuale utente

Central Pneumatic

Central Pneumatic 54700 Manuale utente

Central Pneumatic

Central Pneumatic 94802 Manuale utente

Central Pneumatic

Central Pneumatic 92849 Manuale utente

Central Pneumatic

Central Pneumatic Earthquake 65159 Manuale di installazione

Central Pneumatic

Central Pneumatic 95801 Manuale elenco delle parti

Central Pneumatic

Central Pneumatic 95098 Manuale utente

Central Pneumatic

Central Pneumatic Central Pneumatic 1/4" Stubby Air Ratchet... Manuale utente

Central Pneumatic

Central Pneumatic 99792 Manuale di installazione

Central Pneumatic

Central Pneumatic 66886 Manuale di installazione

Central Pneumatic

Central Pneumatic 93216 Manuale utente

Central Pneumatic

Central Pneumatic 68423 Manuale utente

Central Pneumatic

Central Pneumatic 66874 Manuale di installazione

Central Pneumatic

Central Pneumatic 60801 Istruzioni per il montaggio

Central Pneumatic

Central Pneumatic 68018 Manuale di installazione

Central Pneumatic

Central Pneumatic 68426 Manuale utente

Central Pneumatic

Central Pneumatic Contractor 93197 Manuale utente

Central Pneumatic

Central Pneumatic 47706 Manuale utente

Central Pneumatic

Central Pneumatic Contractor 46365 Manuale utente

Central Pneumatic

Central Pneumatic 47214 Manuale di istruzioni originale

Manuali Utensili elettrici popolari di altre marche

AEG

AEG OMNI-JS Manuale utente

SIP

SIP 01533 Manuale utente

Ribimex

Ribimex PRS499 Manuale utente

3M Fiber Optic Connector Crimp Tool Manuale utente

Ryobi

Ryobi P524 Manuale utente

ROJEK

ROJEK FSN 300A Manuale utente

Kemper

Kemper 1740PRO Manuale utente

WABCO

WABCO OptiTire Manuale utente

EINHELL

EINHELL TE-MS 18/210 Li Manuale utente

Orgapack

Orgapack OR-T 85 Guida rapida

TOUGHCUT

TOUGHCUT Diamond 400 Manuale utente

Yaros

Yaros PB-3603 Manuale utente

Fein

Fein BSS 2.0 E Guida all'installazione

Baileigh Industrial

Baileigh Industrial SS-2725 Manuale utente

Milwaukee

Milwaukee 2674-20 Manuale utente

Fein

Fein BLs 1.6 Manuale utente

Princess

Princess Electric Multi Sharpener Manuale utente

FOREDOM

FOREDOM K.1050 Manuale