Central Pneumatic Contractor 46365 Manuale utente

1/2” CROWN AIR ST1/2” CROWN AIR ST

1/2” CROWN AIR STAPLERAPLER

APLERAPLER

APLER

ASSEMBLY AND OPERATING INSTRUCTIONS

3491 Mission Oaks Blvd., Camarillo, CA 93011

Visit our Web site at http://www.harborfreight.com

For technical questions and replacement parts, please call 1-800-444-3353

46365

artwork contained herein may be reproduced in any shape or form without the express written consent

of Harbor Freight Tools.

SKU 46365 Page 2

Specifications

Save This Manual

You will need the manual for the safety warnings and precautions, assembly

instructions, operating and maintenance procedures, parts list and diagram. Keep

your invoice with this manual. Write the invoice number on the inside of the front

cover. Keep the manual and invoice in a safe and dry place for future reference.

Safety Warnings and Precautions

WARNING: When using tool, basic safety precautions should always be fol-

lowed to reduce the risk of personal injury and damage to equipment.

Read all instructions before using this tool!

1. Keep work area clean. Cluttered areas invite injuries.

2. Observe work area conditions. Do not use machines or power tools in

damp or wet locations. Don’t expose to rain. Keep work area well lighted. Do

not use electrically powered tools in the presence of flammable gases or

liquids.

3. Keep children away. Children must never be allowed in the work area. Do

not let them handle machines, tools, or extension cords.

4. Store idle equipment. When not in use, tools must be stored in a dry

location to inhibit rust. Always lock up tools and keep out of reach of children.

5. Do not force tool. It will do the job better and more safely at the rate for

which it was intended. Do not use inappropriate attachments in an attempt to

exceed the tool capacity.

6. Use the right tool for the job. Do not attempt to force a small tool or

attachment to do the work of a larger industrial tool. There are certain

applications for which this tool was designed. Do not modify this tool and do

not use this tool for a purpose for which it was not intended.

ITEM

Overall Dimensions

Wrenches

Staple Specs.

Operating Pressure

CFM

Magazine Capacity

Air Inlet Size

Net Weight

DESCRIPTION

8-1/2” x 1-7/8” x 5-3/4”

3mm and 4mm

1/2” Crown, 18GA, 1/4”-5/8”

55-95 PSI

4-6

100 Staples

1/4” NPT

2.05 Lb.

REV 09/05

SKU 46365 Page 3

7. Dress properly. Do not wear loose clothing or jewelry as they can be

caught in moving parts. Protective, electrically non-conductive clothes and

non-skid footwear are recommended when working. Wear restrictive hair

covering to contain long hair.

8. Use eye and ear protection. Always wear ANSI approved impact safety

goggles.

9. Do not overreach. Keep proper footing and balance at all times. Do not

reach over or across running machines.

10. Maintain tools with care. Keep tools sharp and clean for better and safer

performance. Follow instructions for lubricating and changing accessories.

Inspect tool cords periodically and, if damaged, have them repaired by an

authorized technician.The handles must be kept clean, dry, and free from oil

and grease at all times.

11. Disconnect power. Unplug tool when not in use.

12. Remove adjusting keys and wrenches. Check that keys and adjusting

wrenches are removed from the tool or machine work surface before plugging

it in.

13. Avoid unintentional starting. Do not carry any tool with your finger on the

trigger, whether it is plugged in or not.

14. Stay alert. Watch what you are doing, use common sense. Do not operate

any tool when you are tired.

15. Check for damaged parts. Before using any tool, any part that appears

damaged should be carefully checked to determine that it will operate

properly and perform its intended function. Check for alignment and binding

of moving parts; any broken parts or mounting fixtures; and any other

condition that may affect proper operation. Any part that is damaged should

be properly repaired or replaced by a qualified technician.

16. Guard against electric shock. Prevent body contact with grounded

surfaces such as pipes, radiators, ranges, and refrigerator enclosures.

17. Replacement parts and accessories. When servicing, use only identical

replacement parts. Use of any other parts will void the warranty. Only use

accessories intended for use with this tool. Approved accessories are

available from Harbor Freight Tools.

18. Do not operate tool if under the influence of alcohol or drugs. Read

warning labels on prescriptions to determine if your judgment or reflexes are

impaired while taking drugs. If there is any doubt, do not operate the tool.

19. Use proper size and type extension cord. If an extension cord is required

SKU 46365 Page 4

for the Air Compressor, it must be of the proper size and type to supply the

correct current to the tool without heating up. Otherwise, the extension cord

could melt and catch fire, or cause electrical damage to the tool. If you are

using the tool outdoors, use an extension cord rated for outdoor use.

(signified by “WA” on the jacket).

21. Maintenance. For your safety, service and maintenance should be

performed regularly by a qualified technician.

Note: Performance of this tool (if powered by line voltage) may vary depending on

variations in local line voltage. Extension cord usage may also affect tool perfor-

mance.

Special Warnings for this Tool

It is especially important that you read and comply with the following safety

precautions.

1. Never, under any circumstances, press the tip of this tool against another

person or yourself.

2. Excess air may remain in the tool even after the tool is disconnected from

the air supply. For this reason, be especially careful never to carry this tool

with your finger on the trigger, and do not press the tip against any surface

even when the tool is not connected to an air supply.

3. While using this tool, be sure to keep fingers, hands and all other body parts

away from the tip of the tool.

4. Never use combustible gas as a power source.

5. Never use gasoline or other flammable liquids to clean the Stapler.

6. Do not exceed the maximum operating pressure of 95 PSI as stated in the

Specifications Chart and warning label.

7. Ear protection is required for the operator and others in the work area.

8. Never attempt to drive staples on top of other staples.

9. Never attempt to keep the Trigger depressed with tape or wire.

10. Never leave the tool unattended or connected to the air supply when not in

use.

11. Do not throw the tool or use it as a hammer to knock material into place.

12. Avoid prolonged use of the Stapler, and do not use this tool if you have back,

neck or other bodily injuries that might be aggravated by the jerking motion

of the tool. Stop using this tool if you experience pain in your arms or hands.

SKU 46365 Page 5

13. Do not use this tool if it is not loaded, as this will accelerate wear on the tool.

14. Be sure all hoses and fittings are free from damage and dirt. Replace any

part that does not appear to be operating properly.

Warning: People with pacemakers should consult with their physician(s)

before using this product; operation of equipment in close proximity to a heart

pacemaker could cause interference or failure of the pacemaker.

Warning: The warnings, cautions, and instructions discussed in this instruc-

tion manual cannot cover all possible conditions and situations that may oc-

cur. It must be understood by the operator that common sense and caution

are factors which cannot be built into this product, but must be supplied by

the operator.

Unpacking

When unpacking, check to make sure all parts listed on Page 7 are included.

If any parts are missing or broken, please call Harbor Freight Tools at the number

on the cover of this manual.

Maintenance

1. Do not store the Stapler in cold or freezing temperatures. If you are

operating the Stapler in cold weather, use a permanent antifreeze as

lubricant. Certain drying agents may damage o-rings and seals, so be sure

to check these periodically.

2. It is recommended that you use an Oiler with this tool, especially if you use

this tool regularly. Be sure the check the oil level in the Oiler before each

use, and during prolonged periods of use.

3. If you are not using an Oiler, you must lubricate the Stapler before and after

each use. Be sure to disconnect the tool from the air supply if you are

lubricating it by hand. To lubricate this tool: add 5-6 drops of air tool

lubrication to the Air Inlet. Do not use detergent oil or oil adhesives. Run the

Stapler for a short time after lubrication and wipe off all excess oil.

4. A filter (not included) can be used to remove liquid and solid impurities which

may rust or block internal parts and mechanisms. Periodically check the

Filter and drain any water.

SKU 46365 Page 6

Air Connection

Note: Air Compressor is not supplied.

You may use Quick-Couplers and Quick-Connectors (not supplied) as shown in the

diagram above. Do not connect Couplers directly to the Air Inlet. Doing so will

increase the overall bulk of the tool and strain the inlet threads.

1. Read and follow all safety precautions as listed on Pages 2-5 of this manual.

2. Acquire a Union Fitting (not supplied) and screw into the Air Plug [32, see

Assembly Diagram on Page 8]. Tighten with a wrench.

3. Attach a Quick-Connector (not supplied) to the Union Fitting if desired. This

allows quick exchange of the Air Hose to other air tools.

4. If staples do not drive down tightly, adjust to a higher pressure setting until

satisfactory. Reduce air pressure if the staples are being driven too deep.

This air tool requires lubrication during operation. For best results, it is recom-

mended to have an Oiler and Water Filter in line with the Air Supply as shown.

This will extend the life of the tool.

Loading the Stapler

When loading, the Stapler must be discon-

nected from the Air Compressor Hose.

1. Only use the proper size and type of staple

with this tool, as specified in the chart on

Page 2.

2. Disconnect tool from the air supply.

3. Depress the Click Lever [34] to release the

spring-loaded Magazine Assembly [51]

from the Upper Magazine [47]. Slide the Magazine Assembly out as far as it

will go. See Figure A, right.

4. Turn the Stapler upside down. Place a full clip of staples inside the Upper

Magazine so the pointed ends of the staples are directed away from the tool.

STAPLER

Figure A

SKU 46365 Page 7

5. Slide the Magazine Assembly back into place until it clicks.

Operation

1. Grip the Body [18] of the Stapler with both hands and press the Nozzle [19]

against the surface you wish to staple. Be sure to keep your hands, fingers

and other body parts away from the Nozzle.

2. Depress the Trigger [28] to activate the Stapler.

Your 1/2” Crown Air Stapler is easy to load and fun to use. With its comfortable

grip and lightweight body, your Stapler is an ideal tool for working with upholstery,

insulation, picture frames and more.

Parts List

PLEASE READ THE FOLLOWING CAREFULLY

THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS DIAGRAM IN THIS MANUAL AS A

REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER NOR DISTRIBUTOR MAKES ANY REPRESENTATION OR

WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT

OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER

AND/OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE

UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS AND NOT BY THE BUYER. THE BUYER ASSUMES ALL

RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS

THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.

DESCRIPTION

Screw 5 x 22

Exhaust Cover

Compression Spring

Seal, Air

Cylinder Cap

O-Ring 11.8 x 2.4

Piston Set

Washer 7.3 x 4.7 x 0.8

Head Valve Piston

Piston Stopper

O-Ring 26.6 x 2.4

O-Ring 21.3 x 3

Collar

O-Ring 33 x 2

Cylinder

Bumper

Gasket

Body

Nozzle

Seal, Air

Trigger Valve Head

Trigger Valve Stem

O-Ring 3.8 x 1.5

Trigger Valve Guide

O-Ring 9.8 x 1.9

Compresion Spring

E-Ring up2.5

Trigger

ITEM

DESCRIPTION

Step Pin up5 x 17.5

O-Ring 31.42 x 2.62

Tail Cover

Air Plug

Compression Spring

Click Lever

Step Pin up5 x 26

O-Ring 17.3 x 3

Piston Head

Driver Blade Pin

Outer Spring Pin 4 x 10

Inner Spring Pin 2.5 x 10

Driver Blade

Screw 4 x 16

Driver Guide

Spacer

Screw 4 x 8

Stopper

Upper Magazine

Screw 4 x 8

Extension Spring

Pusher

Magazine Assembly

Cylinder Cap Set

Head Valve Piston Set

Collar Set

Cylinder Assembly

Trigger Valve Set

ITEM

SKU 46365 Page 8

Assembly Drawing

NOTE: Some parts are

listed and shown for

illustration purposes only

and are not available

individually as replacement

parts.

SKU 46365 Page 9

WARRANTY CARD

REV 03/06

LIMITED 1 YEAR

3491 Mission Oaks Blvd. • • Camarillo, CA 93011 • (800) 444-3353

apply to damage due directly or indirectly to misuse, abuse, negligence or accidents; repairs or

arising from the use of our product. Some states do not allow the exclusion or limitation of

incidental or consequential damages, so the above limitation of exclusion may not apply to you.

bear the cost of returning the product.

state to state.

WARRANTY

P.O. Box 6009

Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and

durability standards, and warrants to the original purchaser that this product is free from defects in

materials and workmanship for a period of 1 year from the date of purchase. This warranty does not

alterations outside our facilities; or to lack of maintenance. We shall in no event be liable for death,

injuries to persons or property, or for incidental, contingent, special or consequential damages

To take advantage of this warranty, the product or part must be returned to us with transportation

charges prepaid. Proof of purchase date and an explanation of the complaint must accompany the

merchandise. If our inspection verifies the defect, we will either repair or replace the product at our

election or we may elect to refund the purchase price if we cannot readily and quickly provide you

with a replacement. We will return repaired products at our expense, but if we determine there is no

defect, or that the defect resulted from causes not within the scope of our warranty, then you must

This warranty gives you specific legal rights and you may also have other rights which vary from

Indice

Altri manuali Central Pneumatic Utensili elettrici

Central Pneumatic

Central Pneumatic 93216 Manuale utente

Central Pneumatic

Central Pneumatic 66886 Manuale di installazione

Central Pneumatic

Central Pneumatic 54753 Manuale elenco delle parti

Central Pneumatic

Central Pneumatic 167 Manuale utente

Central Pneumatic

Central Pneumatic 95119 Manuale di installazione

Central Pneumatic

Central Pneumatic 68018 Manuale di installazione

Central Pneumatic

Central Pneumatic 95098 Manuale utente

Central Pneumatic

Central Pneumatic 47706 Manuale utente

Central Pneumatic

Central Pneumatic 67473 Manuale di installazione

Central Pneumatic

Central Pneumatic 66984 Manuale utente

Central Pneumatic

Central Pneumatic 68423 Manuale utente

Central Pneumatic

Central Pneumatic 67996 Manuale utente

Central Pneumatic

Central Pneumatic 46446 Manuale utente

Central Pneumatic

Central Pneumatic Contractor 90399 Manuale utente

Central Pneumatic

Central Pneumatic 91107 Manuale utente

Central Pneumatic

Central Pneumatic 98898 Manuale di installazione

Central Pneumatic

Central Pneumatic 54700 Manuale utente

Central Pneumatic

Central Pneumatic 96661 Istruzioni per il montaggio

Central Pneumatic

Central Pneumatic 92849 Manuale utente

Central Pneumatic

Central Pneumatic 65902 Manuale di installazione

Central Pneumatic

Central Pneumatic CENTRAL PNEUMATIC 68128 Manuale di installazione

Central Pneumatic

Central Pneumatic 94802 Manuale utente

Central Pneumatic

Central Pneumatic Earthquake 65159 Manuale di installazione

Central Pneumatic

Central Pneumatic 36567 Manuale utente

Manuali Utensili elettrici popolari di altre marche

AEG

AEG OMNI-JS Manuale utente

SIP

SIP 01533 Manuale utente

Ribimex

Ribimex PRS499 Manuale utente

3M Fiber Optic Connector Crimp Tool Manuale utente

Ryobi

Ryobi P524 Manuale utente

ROJEK

ROJEK FSN 300A Manuale utente

Kemper

Kemper 1740PRO Manuale utente

WABCO

WABCO OptiTire Manuale utente

EINHELL

EINHELL TE-MS 18/210 Li Manuale utente

Orgapack

Orgapack OR-T 85 Guida rapida

TOUGHCUT

TOUGHCUT Diamond 400 Manuale utente

Yaros

Yaros PB-3603 Manuale utente

Fein

Fein BSS 2.0 E Guida all'installazione

Baileigh Industrial

Baileigh Industrial SS-2725 Manuale utente

Milwaukee

Milwaukee 2674-20 Manuale utente

Fein

Fein BLs 1.6 Manuale utente

Princess

Princess Electric Multi Sharpener Manuale utente

FOREDOM

FOREDOM K.1050 Manuale