Chamberlain TRICODE TCG2 Manuale utente
®
TRICODE® TCG2 DUAL
CHANNEL RECEIVER
USED FOR TCG1 AND TCG2
The TriCode®digital receivers are designed for use with automatic
garage/gate operators and access control systems. All TriCode®
products may be matched with Linear/Delta-3TM, Multi-CodeTM and
StanleyTM radio products which may already be installed.
The TriCode®radio format provides a potential of 1024 different
digital codes. For Linear/Delta-3TM compatible products 256
different digital codes are available. The codes are set using a
10-position DIP switch system.
U.S. Patent 6,915,146
SPECIFICATIONS
Output Rating: 5 Amps 28Vac/Vdc Max.
Power: 12Vdc or 18 to 34Vac/Vdc, @ 30ma
RF Frequency: 300 or 310 MHz
Accessory Transmitters: TC1, TC2 and TC4
Antenna Extension Kit: TCEXT
NOTICE: To comply with FCC and or Industry Canada (IC) rules, adjustment or modifications of
this receiver and/or transmitter are prohibited, except for changing the code setting or replacing
the battery. THERE ARE NO OTHER USER SERVICEABLE PARTS.
Tested to Comply with FCC Standards FOR HOME OR OFFICE USE. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired operation.
To prevent possible SERIOUS INJURY or DEATH from electrocution:
• Be sure power is NOT connected BEFORE installing the receiver.
To prevent possible SERIOUS INJURY or DEATH from a moving
gate or garage door:
• ALWAYS keep transmitters out of reach of children. NEVER permit
children to operate or play with remote control transmitters.
• Activate gate or door ONLY when it can be seen clearly, is properly
adjusted, and there are no obstructions to door travel.
• ALWAYS keep gate or garage door in sight until completely closed.
NEVER permit anyone to cross path of moving gate or door.
WARNING
CAUTION WARNING
WARNING
2
POWER & OUTPUT RELAY SWITCH SETTINGS
24V AC/DC CH1 N/O CH2 N/O
P3
12V 24V
CH1
MODE
CST MNT CH2
MODE
CST MNT
RELAY
CH1-MODE
RELAY
CH2-MODE
JUMPER
(P3)
Mounting Holes
Mounting Holes
LINEAR
MULTI
STAN
12V 24V
CST MNT CST MNT
P3
CH1
MODE
CH2
MODE
123 456 78 910
O
N
123 456 78 910
O
N
Figure 1
Power Supply Selection Setting
The TriCode®receiver is factory set for 24 volt power input if
12 volt is required.
Remove front cover of receiver by turning screws
counterclockwise a 1/4 of a turn until each releases. Set jumper
(P3) to either 12 or 24 volt setting depending on your power
input (Figure 1).
Setting Output Relay Mode
The TriCode®receiver is factory set for momentary relay output
“MNT”.
• Momentary mode: The output relay will be on for .5 seconds
before turning off.
• Constant pressure mode: Output relay is continuously on
while receiving matching/valid ID code from transmitter. The
output relay will turn off immediately once receiver does not
receive a matching/valid ID code from the transmitter.
If constant pressure mode is desired, move mode jumper
from “MNT” to “CST” (Figure 1).
NOTE: The relay output is an isolated normally open contact.
NOTE: To avoid the possibility of duplicating codes in adjacent
systems, all transmitters and receivers should be re-coded prior
to operation. Unless using maximum number of codes the
following four codes should not be used:
· All DIP Switches ON
· All DIP Switches OFF
· DIP Switches alternating ON/OFF
· DIP Switches alternating OFF/ON
Receivers should be installed at least 5' apart to avoid cross-talk.
After completing installation, operate transmitter outside of
building to make certain the chosen DIP switch setting does not
operate with nearby garage door operators and/or security
systems. If so, select another DIP switch setting and check the
coded signal again. Repeat as necessary.
RECEIVER MOUNTING
Mount receiver to wall using #6 hardware (not provided).
Hardware used will depend on mounting application. Refer to
Figure 1 for receiver mounting hole locations.
ANTENNA MOUNTING
Screw on antenna clockwise and slide rubber boot down to meet
O-ring.
3
CONFIGURATION & DIP SWITCH SETTINGS
24Vac/Vdc CH1 N/O CH2 N/O
Delta-3/Linear
Multi-Code
Stanley
DIP
Switches
Configuration
Switch
Channel 2 DIP Switch
Channel 1 DIP Switch
TM
TM
TM
LINEAR
MULTI
STAN
CH1
MODE
CH2
MODE
12V 24V
CST MNT CST MNT
P3
12345678910
O
N
12345678910
O
N
1234 5 6 78910
O
N
1234 5 6 78910
O
N
Figure 4
Figure 2
Multi/ Stanley
(1 Thru 10)
Linear/ Delta-3
(1 Thru 8)
1 2 3 4 5 6 7 8 9 10
O
N
O
F
F
TM
TM
DIP
Switch
Delta-3/ Linear
Multi-Code
Stanley
310 MHz
300 MHz
310 MHz
TM
TM
TM
Configuration
Switch
Setting DIP Switch
The TriCode®receiver DIP switch CH1 is factory set OFF (1-10)
and CH2 is factory set ON (1-10).
Locate the 10 position DIP Switch. If this is a new installation
using TriCode®transmitters, randomly set switches matching
those of the transmitters. Never use factory setting. If receiver is
used with Linear/Delta-3TM, Multi-CodeTM or StanleyTM transmitters,
match the receiver DIP Switch to the above transmitters. Some
transmitters may use toggle switches and it may be difficult to
determine ‘ON’ and ‘OFF’. If so, try reversing the setting on the
TriCode®DIP Switch (Figures 3 and 4).
NOTE: In 'LINEAR/DELTA-3TM' mode (8-bits system) the last 2
bits (DIP #9 & 10) settings are ignored. They can be left in either
‘ON’ or ‘OFF’ settings.
Setting the Configuration Switch
The TriCode®receiver is factory set for Linear/Delta-3TM.
Locate the configuration switch and set it to the desired RF mode
of operation (Figures 2 and 4). Modes are as follows:
Linear/Delta-3TM: works with all “Linear/Delta-3TM” transmitters
transmitted at 310 MHz using 8-bits ID system.
MultiTM: works with all “Multi-CodeTM” transmitters transmitted at
300 MHz using 10-bits ID system.
StanleyTM: works with all “StanleyTM radio” transmitters
transmitted at 310 MHz using 10-bits ID system.
Figure 3
© 2007, The Chamberlain Group, Inc.
01-17469D All Rights Reserved
Power Supply Connections
A prewired gasket pigtail is included for your convenience (see Figure 5 for outgoing wires).
NOTE: For internal wire connections refer to Figure 6.
24V AC/DC CH1 N/O CH2 N/O
Red
Black
White/Green Stripe
White/Yellow Stripe
Blue/Brown Stripe
Blue/Orange Stripe
LINEAR
MULTI
STAN
12345678910
O
N
CST MNT
CH1
MODE
CST MNT CH2
MODE
12345678910
O
N
12V 24V
P3
Figure 5
POWER CONNECTIONS
Red
Black
White/Green
White/Yellow
Blue/Brown
Blue/Orange
24V
AC/DC
Ch1
N/O
Ch2
N/O
Power
Supply
12V/24V
Figure 6
Indice
Altri manuali Chamberlain Ricevitore
Chamberlain
Chamberlain 955D Manuale utente
Chamberlain
Chamberlain LiftMaster 422LM Manuale utente
Chamberlain
Chamberlain LiftMaster PROFESSIONAL 635-315LM Manuale utente
Chamberlain
Chamberlain 050ACTWF Manuale utente
Chamberlain
Chamberlain 050DCTWFLK Manuale utente
Chamberlain
Chamberlain 41A6128 Manuale utente
Chamberlain
Chamberlain 050DCTWF Manuale utente
Chamberlain
Chamberlain PPWR Manuale utente
Chamberlain
Chamberlain LiftMaster CPT1 Manuale utente
Chamberlain
Chamberlain 7433E Manuale utente
Chamberlain
Chamberlain 412HM Manuale utente
Chamberlain
Chamberlain 5002EX Manuale utente
Chamberlain
Chamberlain 050ACTWFMC Manuale per l'uso e la cura
Chamberlain
Chamberlain LiftMaster 850LM Manuale utente
Chamberlain
Chamberlain LiftMaster 312HMC Manuale utente
Chamberlain
Chamberlain 1025 Manuale utente
Chamberlain
Chamberlain 635LM - Sears LiftMaster Chamberlain Manuale utente
Chamberlain
Chamberlain TriCode TCR2 Manuale utente
Chamberlain
Chamberlain 8002E Manuale utente
Chamberlain
Chamberlain 050DCTWFLK Manuale utente
