Champtek SG700BT Istruzioni operative

U s e r ’ s M a n u a l

SG700BT Wireless Handheld Linear

Imager Bar code Scanner

User’s Installation and Configuration

Manual

laws, this manual may not, in whole or in part, be copied, photocopied,

reproduced, translated or converted to any electronic medium or machine

readable form without prior written consent of Champtek.

Limited Warranty

Under all circumstances this manual should be read attentively, before

installing and/or using the product. In no event shall Champtek be liable

for any direct, indirect, special, consequential or incidental damages

arising out of the use or inability to use this documentation or product,

even if advised of the possibility of such damages. In particular, Champtek

shall not be liable for any hardware, software, or data that is stored or

used with the product, including the cost of repairing, replacing or

recovering the above. Champtek reserves the right to change parts of the

device at any time without preceding or direct announcement to the client.

Champtek reserves the right to revise this manual, and to make changes in

the contents without obligation to notify any person or entity of the

revision or change. A serial number appears on the product. Make sure that

this official registration number has not been removed. It should be used

whenever servicing by Champtek BV or an authorized Champtek dealer is

necessary.

Notice: The manufacturer shall not be liable for technical or

editorial errors or omissions contained herein; nor for

incidental or consequential damages in connection with the

furnishing, performance or use of the publication

V1.0 Feb. 2012

Table of contents

Table of contents ..................................... 3

INTRODUCTION .......................................... 1

CHAPTER 1 PRODUCT SAFETY ............................. 2

1.1 Safety & Caution ......................... 2

1.2 FCC Warning .............................. 3

CHAPTER 2 GENERAL DESCRIPTION ........................ 4

2.1 Use of the SG700BT ....................... 4

CHAPTER 3 INSTALLATION OF THE SG700BT ................ 5

3.1 SG700BT Unpacking ........................ 5

3.2 SG700BT Cradle Installation .............. 6

3.3 SG700BT Setup Bluetooth Communication .... 7

3.3.1 Pairing .................................... 7

3.3.2 Setup SPP Master Mode Communication ........ 7

3.3.3 Setup SPP Slave Mode Communication ......... 9

3.3.4 Setup HID Slave Mode Communication ......... 9

3.3.5 Sleep Mode ................................. 9

3.3.6 Batch Mode ................................ 10

3.3.7 Out of Range .............................. 10

CHAPTER 4 CONFIGURING THE SG700BT ................... 11

4.1 Preface ................................. 11

4.1.1 Changing Scanner Settings with Programming

Codes 11

4.1.2 Programming Flow Chart .................... 12

4.2 Set All Default Parameter ............... 13

4.3 General Process ......................... 13

4.3.1 Abort Configuration ...................... 14

4.3.2 Recall ................................... 14

4.3.3 Version Information ...................... 14

4.4 Cradle Interface Selection...............14

4.4.1 Interface ................................ 14

4.5 Bluetooth Scanner Setup..................15

4.5.1 Preface .................................. 15

4.5.2 Scanner Mode ............................. 15

4.5.3 *** Batch Mode (“***” means “Quick Setting

Label”, The function can be executed directly by

scanning barcode instead of doing the general

process.) ......................................... 16

4.5.4 Out of Range ............................. 16

4.5.5 Sleep Mode ............................... 16

4.6 Scanner Operation........................17

4.6.1 Reading Mode ............................. 17

4.6.2 Beeper Option ............................ 18

4.6.3 Reading Level ............................ 18

4.6.4 Accuracy Scan ............................ 18

4.6.5 Sensitivity of Continuous Reading ........ 19

4.6.6 Same Code Delay Reading Interval ......... 19

4.6.7 Reverse Output Characters ................ 20

4.7 RS232 Mode Parameters....................20

4.7.1 Baud Rate ................................ 20

4.7.2 Data/Stop Bits ........................... 21

4.7.3 Parity ................................... 21

4.7.4 Handshaking .............................. 22

4.8 Keyboard Wedge Mode Parameters...........24

4.8.1 Terminal Type ............................ 24

4.8.2 Country/Language .......................... 25

4.8.3 Upper/Lower Case .......................... 26

4.8.4 Capslock Detection ........................ 26

4.8.5 Character by ALT Method ................... 27

4.8.6 Select Numerical Pad ...................... 27

4.8.7 Interscan Code Delay ...................... 27

4.9 Output Characters ....................... 28

4.9.1 Select Terminator ......................... 28

4.10 Code Type ............................... 29

4.10.1 Barcode Selection ......................... 29

4.11 UPC/EAN/JAN Parameters .................. 32

4.11.1 Reading Type .............................. 32

4.11.2 Supplemental Setup ........................ 34

4.11.3 Check Digit Transmission .................. 34

4.12 Code 39 Parameters ...................... 35

4.12.1 Type of Code .............................. 35

4.12.2 Check Digit Transmission .................. 35

4.12.3 Output Start/Stop Character ............... 36

4.12.4 Decode Asterisk ........................... 36

4.12.5 Setup Code Length ......................... 36

4.13 Code 128 Parameters ..................... 38

4.13.1 Reading Type .............................. 38

4.13.2 Check Digit Transmission .................. 39

4.13.3 Append FNC2 ............................... 39

4.13.4 Setup Code Length ......................... 39

4.14 Interleave 2 of 5 Parameters ............ 41

4.14.1 Check Digit Transmission .................. 41

4.14.2 Setup Number of Character ................. 41

4.14.3 Brazilian Banking Code ................... 41

4.14.4 Setup Code Length ........................ 42

4.15 Industrial 2 of 5 Parameters.............43

4.15.1 Reading Type ............................. 43

4.15.2 Check Digit Transmission ................. 43

4.15.3 Setup Code Length ........................ 44

4.16 Matrix 2 of 5 Parameters.................45

4.16.1 Check Digit Transmission ................. 45

4.16.2 Setup Code Length ........................ 46

4.17 CODABAR/NW7 Parameters...................47

4.17.1 Setup Start/Stop Characters upon

Transmission ...................................... 47

4.17.2 Transmission Type of Start/Stop .......... 47

4.17.3 Setup Code Length ........................ 48

4.18 Code 93 Parameters.......................50

4.18.1 Check Digit Transmission ................. 50

4.18.2 Setup Code Length ........................ 50

4.19 Code 11 Parameters.......................52

4.19.1 Check Digit Transmission ................. 52

4.19.2 Setup Code Length ........................ 52

4.20 MSI/Plessey Code Parameters..............54

4.20.1 Check Digit Transmission ................. 54

4.20.2 Setup Code Length ........................ 54

4.21 Telepen Parameters.......................56

4.21.1 Type of Code ............................. 56

4.21.2 Check Digit Transmission ................. 56

4.21.3 Setup Code Length ........................ 56

4.22 GS1 Databar Omnidirectional Parameters...58

4.22.1 Check Digit Transmission ................. 58

4.22.2 Application ID ............................ 58

4.22.3 Symbology ID .............................. 58

4.23 GS1 Databar Limited Parameters .......... 59

4.23.1 Check Digit Transmission .................. 59

4.23.2 Application ID ............................ 59

4.23.3 Symbology ID .............................. 59

4.24 GS1 Databar Expanded Parameters ......... 60

4.24.1 Symbology ID .............................. 60

CHAPTER 5 MISCELLANEOUS PARAMETERS .................. 61

5.1 Bar Code ID ............................. 61

5.1.1 Default Barcode ID ........................ 61

5.1.2 User Define Code ID ....................... 62

5.2 Preamble and Postamble Insertion ........ 64

5.2.1 Setup Insertion ........................... 64

5.2.2 Insertion Set Number ...................... 65

5.2.3 Code Type for Insertion ................... 66

5.2.4 Position to Be Inserted ................... 68

5.2.5 Characters to Be Inserted ................. 68

5.3 Character Deletion ...................... 68

5.3.1 Deletion Set Number ....................... 70

5.3.2 Code Type for Deletion .................... 70

5.3.3 Position to Be Deleted .................... 72

5.3.4 Number of Characters to Be Deleted ........ 72

APPENDIXES ........................................... 73

A. Decimal Value Table ..................... 73

B. ASCII Value Table ........................ 74

C. ASCII Table ............................. 75

D. Function Key Table ...................... 81

E. Technical Specifications.................82

F. Scan Map.................................84

G. LED Indicator Status.....................85

H. Test Symbologies.........................86

Quick Configuration...........................88

INTRODUCTION

SG700BT is a gun-type barcode scanner which is

designed specifically for retail market. To the brand

new series of SG700BT, we add on more user-friendly

functions with detachable interface cable that makes it

easier to be operated by the customers.

Speaking of the performance, this scanner supports

middle to long range mode.SG700BT which supports the

reading depth up to 50 centimeters, and the scan speed

is up to 500 scans per second.

In short, SG700BT is absolutely a high performance gun-

type scanner which provides the customer with the most

cost-effective solution in the market. It is perfectly

suitable and definitely the best choice for any

retailers using POS environment.

The SG700BT is available in various interface types,

RS232, Keyboard Wedge, USB HID or Virtual comport

interface, so there is always a solution to connect the

SG700BT to your POS system.

CHAPTER 1 PRODUCT SAFETY

1.1 Safety & Caution

1. Please read the following safety statement carefully.

2. Please preserve this user‟s manual for reference

sometime.

3. Before cleaning the SG700BT, the users must cut off

all AC power. Do not use liquid or spray type of

detersive to clean the SG700BT. Please use dampish

cotton cloth to clean the SG700BT.

4. The outlet must set nearby the SG700BT for connecting

power easily.

5. Keep the SG700BT dry to avoid short circuit.

6. During installation you must fix the equipment at

solid table to avoid damage caused by falling.

7. Before inserting power please ensure the voltage is

healthy to the equipment.

8. For safety please tie wire well and don‟t put

anything on the wire.

9. If you don‟t use this equipment for long time, please

cut off the power to avoid damage from surge power.

10. Don‟t spray any liquid on this scanner because it may

cause a fire or short circuit.

11. Please do not open the equipment. For safety only the

qualified serviceman can open the equipment.

12. If there are the following situations please contact

the qualified serviceman to check this equipment.

(a) The damage of wire or pin of power supply.

(b) Some Liquid infiltrate into the equipment.

environment.

(d) The equipment can‟t work well.

(e) The equipment has any obvious damage, making the

SG700BT working abnormally.

13. Don‟t store the SG700BT at the temperature lower than

-20°C (-4°F) or higher than +70°C (158°F) to avoid

any damage.

Altri manuali per SG700BT

Indice

Altri manuali Champtek Lettore di codici a barre

Champtek

Champtek IG300BT Manuale utente

Champtek

Champtek SLIM S-9080i Manuale utente

Champtek

Champtek IG500 Manuale utente

Champtek

Champtek VM200 Manuale utente

Champtek

Champtek MB200 Series Manuale utente

Champtek

Champtek IG300BT Manuale utente

Champtek

Champtek SCANTECH ID VM200 Manuale utente

Champtek

Champtek SG700BT Manuale utente

Champtek

Champtek IG-300 Manuale utente

Manuali Lettore di codici a barre popolari di altre marche

POSMicro

POSMicro Datalogic PowerScan D7100 Manuale utente

Marson

Marson MT780 Guida rapida alla configurazione

NCR

NCR RealPOS Manuale utente

Motorola

Motorola SE3300 Guida rapida alla configurazione

Element

Element P130BT Manuale utente

Motorola

Motorola Symbol LS3008 Manuale di installazione e funzionamento

Meec tools

Meec tools OBD-II / VAG Manuale utente

SICK

SICK CLP 100 Manuale utente

Royal Tag SA

Royal Tag SA I-Read Manuale utente

Welch Allyn

Welch Allyn IMAGETEAM 3800 Manuale utente

Meteor

Meteor 8310 Manuale utente

Denso

Denso BHT-500B Manuale utente

Datalogic

Datalogic Heron HD3130 Manuale utente

Motorola

Motorola MP6000 Istruzioni di montaggio

Newland

Newland NLS-HR15-BT Manuale utente

ARTDEV

ARTDEV AS-1310 Manuale utente

Aopos

Aopos AS290 Manuale utente

ENS

ENS 367-5455 Manuale utente