Cisco Engine 611 Manuale utente

Corporate Headquarters:

Cisco Systems, Inc., 170 West Tasman Drive, San Jose, CA 95134-1706 USA

Installing Hard Disk Drives in the Cisco Wide

Area Application Engine 611

Product Numbers: DISK-611SC-144GB=, DISK-611SC-300GB=

This publication provides basic instructions for installing SCSI hard disk drive options in the Wide Area

Application Engine 611 (WAE-611). These instructions are intended for experienced technicians.

Contents

This publication contains the following sections:

•Safety Overview, page 1

•Introduction, page 3

•Removing the Bezel and Cover, page 4

•Assigning SCSI IDs, page 6

•Removing and Replacing a SCSI Hard Disk Drive, page 7

•Replacing the Cover and Bezel and Completing the Installation, page 10

•Obtaining Documentation, page 11

•Cisco Product Security Overview, page 11

•Obtaining Technical Assistance, page 12

Note For translations of the warnings in this publication, see the “Related Documentation” section on page 3.

Safety Overview

Safety warnings appear throughout this publication in procedures that may harm you if performed

incorrectly. A warning symbol precedes each warning statement.

Installing Hard Disk Drives in the Cisco Wide Area Application Engine 611

78-17404-01

Safety Overview

Protecting Against Electrostatic Discharge

Static electricity can harm delicate components inside the device. To prevent static damage, discharge

static electricity from your body before you touch any of your system’s electronic components. You can

do so by touching an unpainted metal surface on the chassis.

You can also take the following steps to prevent damage from electrostatic discharge (ESD):

•When unpacking a static-sensitive component from its shipping carton, do not remove the

component from the antistatic packing material until you are ready to install the component in your

system. Just before unwrapping the antistatic packaging, be sure to discharge static electricity from

your body.

•When transporting a sensitive component, first place it in an antistatic container or packaging.

•Handle all sensitive components in a static-safe area. If possible, use antistatic floor pads and

workbench pads.

Rack Installation Safety Guidelines

Before installing your device in a rack, review the following guidelines:

•Two or more people are required to install the device in a rack.

•Ensure that the room air temperature is below 95°F (35°C).

•Do not block any air vents; usually 6 inches (15 cm) of space provides proper airflow.

•Plan the device installation starting from the bottom of the rack.

•Install the heaviest device in the bottom of the rack.

•Do not extend more than one device out of the rack at the same time.

•Remove the rack doors and side panels to provide easier access during installation.

•Connect the device to a properly grounded outlet.

•Do not overload the power outlet when installing multiple devices in the rack.

•Do not place any object weighing more than 110 lb (50 kg) on top of rack-mounted devices.

Warning

IMPORTANT SAFETY INSTRUCTIONS

This warning symbol means danger. You are in a situation that could cause bodily injury. Before you

work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar

with standard practices for preventing accidents. Use the statement number provided at the end of

each warning to locate its translation in the translated safety warnings that accompanied this

device.

Statement 1071

SAVE THESE INSTRUCTIONS

Installing Hard Disk Drives in the Cisco Wide Area Application Engine 611

78-17404-01

Introduction

The WAE-611 supports two 1-inch (2.54-cm) slim 3.5-inch (8.89-cm) low voltage differential (LVD)

hard disk drives. The WAE-611 requires SCSI hard disk drives.

Warning

Only trained and qualified personnel should be allowed to install, replace, or service this equipment.

Statement 1030

Required Tools

The following tools are required to perform the hard disk drive installation:

•Antistatic mat or foam pad to support and protect the removed hard disk drive

•Your own ESD-prevention equipment or the disposable grounding wrist strap included with all

upgrade kits, field-replaceable units (FRUs), and spares

Caution Always use an ESD wrist strap when handling modules or coming into contact with internal components.

Warning

Blank faceplates and cover panels serve three important functions: they prevent exposure to

hazardous voltages and currents inside the chassis; they contain electromagnetic interference (EMI)

that might disrupt other equipment; and they direct the flow of cooling air through the chassis. Do not

operate the system unless all cards, faceplates, front covers, and rear covers are in place.

Statement

1029

Warning

The safety cover is an integral part of the product. Do not operate the unit without the safety cover

installed. Operating the unit without the cover in place will invalidate the safety approvals and pose

a risk of fire and electrical hazards.

Statement 117

Related Documentation

Use this publication in conjunction with the following hardware documentation:.

•Cisco Wide Area Application Engine 511 and 611 Hardware Installation Guide

•Regulatory Compliance and Safety Information for the Cisco Content Networking Product Series

Note To access these publications on Cisco.com, see the “Obtaining Documentation” section on page 11.

Installing Hard Disk Drives in the Cisco Wide Area Application Engine 611

78-17404-01

Removing the Bezel and Cover

Warning

Before working on a system that has an on/off switch, turn OFF the power and unplug the power cord.

Statement 1

Warning

Do not work on the system or connect or disconnect cables during periods of lightning activity.

Statement 1001

Warning

When installing or replacing the unit, the ground connection must always be made first and

disconnected last.

Statement 1046

To remove the bezel and cover, follow these steps:

Step 1 Review the information in the “Protecting Against Electrostatic Discharge” section on page 2.

Step 2 Power down the device and all attached devices. Disconnect the power cord and all external cables.

Step 3 Remove the bezel as shown in Figure 1.

a. Press the release tabs on the bezel and pull the bezel away from the chassis.

b. Store the bezel in a safe place.

Figure 1 Removing the Bezel

Step 4 To remove the cover, loosen the captive screw (labeled 1 in Figure 2) on the rear of the cover.

151560

Installing Hard Disk Drives in the Cisco Wide Area Application Engine 611

78-17404-01

Removing the Bezel and Cover

Figure 2 Removing the Cover

Step 5 Slide the cover back. Lift it up and off the device.

Caution For proper cooling and airflow, replace the cover before turning on the device. Operating the device for

extended periods (over 30 minutes) with the cover removed might damage device components.

Step 6 Before you begin working inside the chassis, familiarize yourself with the location of the components

that you will be handling. Figure 3 shows the front of the chassis and the location of the drive bays

behind the bezel.

1Captive screw

151559

Installing Hard Disk Drives in the Cisco Wide Area Application Engine 611

78-17404-01

Assigning SCSI IDs

Figure 3 Location of Drive Bays Behind the Bezel

Assigning SCSI IDs

When you install or replace one or more of the SCSI disk drives in a WAE-611, you must assign a SCSI

ID to each disk drive. The SCSI IDs are assigned by placing or removing jumpers on the disk drive SCSI

ID jumper pins. The hard disk drives in this appliance use the SCSI IDs 0 and 1 only.

To assign the proper SCSI ID to a disk drive, follow these steps:

Step 1 Set the SCSI IDs for your drive by placing jumpers on the appropriate jumper pins, as follows:

•Hitachi disks have a single set of jumpers. Follow these jumper settings instructions for Hitachi

disks:

–

Assign SCSI ID 0 to the disk drive in the first drive bay by removing any jumpers from the

jumper pins.

The first drive bay (drive bay 0) is located below the CD-ROM drive on the left side of your

system. (See Figure 3.)

–

Assign SCSI ID 1 to the disk drive in the second drive bay by placing a jumper on the pins

closest to the power connector. Figure 4 shows the jumper placement for SCSI ID 1.

The second drive bay (drive bay 1) is located below the flash memory card on the right side of

your system. (See Figure 3.)

1CD-ROM drive 2Flash memory card

3Drive bay 1 (right side of chassis front) 4Drive bay 0 (left side of chassis front)

151556

Installing Hard Disk Drives in the Cisco Wide Area Application Engine 611

78-17404-01

Removing and Replacing a SCSI Hard Disk Drive

•Seagate disks have two sets of jumpers. Follow these jumper settings instructions for Seagate disks:

–

Assign SCSI ID 0 to the disk drive in the first drive bay by removing any jumpers from the

jumper pins on both the sets.

The first drive bay (drive bay 0) is located below the CD-ROM drive on the left side of your

system. (See Figure 3.)

–

Assign SCSI ID 1 to the disk drive in the second drive bay by placing a jumper on the pins

closest to the power connector (right-most pins)on both the sets. Figure 4 shows the jumper

placement for SCSI ID 1.

The second drive bay (drive bay 1) is located below the flash memory card on the right side of

your system. (See Figure 3.)

Figure 4 shows the connector end of the hard disk drive and the location of the jumper pins.

Figure 4 Hard Disk Drive Connectors and SCSI ID Jumper Pins

Step 2 To check whether the configuration is correct, refer to the boot time messages on the device console. An

example is as follows:

Attached scsi disk sda at scsi0, channel 0, id 0, lun 0

Attached scsi disk sdb at scsi0, channel 0, id 1, lun 0

Removing and Replacing a SCSI Hard Disk Drive

Warning

Before working on a system that has an on/off switch, turn OFF the power and unplug the power cord.

Statement 1

Warning

Read the installation instructions before connecting the system to the power source.

Statement 1004

1Power connector 2Jumper pins

3SCSI connector 4Jumper placement for SCSI ID 1

151557

1 2 3

Installing Hard Disk Drives in the Cisco Wide Area Application Engine 611

78-17404-01

Removing and Replacing a SCSI Hard Disk Drive

Note All hard disk drives that you use in the WAE should have the same throughput speed rating. Mixing hard

disk drives with different speed ratings will cause all hard disk drives to operate at the lower throughput

speed. Cisco technical support does not support appliances configured with hard disk drives of mixed

speed ratings.

Note The WAE-611 must have two hard disk drives. This system is not supported with a single hard disk drive.

To maintain proper system cooling, do not operate the appliance for more than 10 minutes without a hard

disk drive installed in each bay.

To install a SCSI hard disk drive in the WAE-611, follow these steps:

Step 1 Review the information in the “Protecting Against Electrostatic Discharge” section on page 2.

Step 2 Inspect the new drive for any signs of damage.

Step 3 Power down the device and peripheral devices, and disconnect the power cord and all external cables.

Step 4 Press the release tabs on the bezel, and pull the bezel away from the chassis. (See Figure 1.)

Step 5 Remove the chassis cover. (See Figure 2.)

Step 6 To remove the hard disk drive in either drive bay, work from inside the chassis and disconnect the SCSI

cable from the hard disk drive by using your thumbs to work the cable connector out of the drive

connector. Do not pull directly on the cable itself.

Tip To remove the hard disk drive in the first bay (the bay on the left below the CD-ROM drive),

begin by disconnecting the integrated drive electronics (IDE) cable from the CD-ROM drive for

easier access to the hard disk drive connectors that are below it.

Step 7 Disconnect the power cable from the hard disk drive.

Step 8 Gently pull the carrier handle (labeled 6 in Figure 5), and slide the hard disk drive out of the drive bay.

Step 9 Before you install the new drive in a drive bay, check the jumper pins to make sure that you have the

correct SCSI ID set on the drive, as follows:

•SCSI ID 0 for drive bay 0

•SCSI ID 1 for drive bay 1

Note If drive 0 has failed and you do not want to lose the cached data, you can reconfigure the existing

drive 1 to replace drive 0 (by changing it to SCSI ID 0 in bay 0), and configure the new

replacement drive as drive 1.

Step 10 Slide the new disk drive back into the drive bay with the circuit board on the drive facing up. (See

Figure 3.)

Figure 5 shows the disk drive connector and pin locations and the orientation of the disk drives for

installation. (See also Figure 3.)

Installing Hard Disk Drives in the Cisco Wide Area Application Engine 611

78-17404-01

Removing and Replacing a SCSI Hard Disk Drive

Figure 5 Disk Drive Orientation During Installation

Step 11 Connect the power and SCSI cables to the drive. If you disconnected the IDE cable to the CD-ROM,

reconnect it.

Step 12 Make sure that your cables are lying flat inside the chassis, so that you do not shear them when you

replace the chassis cover.

1SCSI connector 2Jumper pins

3Power connector 4Circuit board facing up

5Drive carrier 6Carrier handle

151557

Installing Hard Disk Drives in the Cisco Wide Area Application Engine 611

78-17404-01

Replacing the Cover and Bezel and Completing the Installation

Warning

This unit is intended for installation in restricted access areas. A restricted access area is where

access can only be gained by service personnel through the use of a special tool, lock and key, or

other means of security, and is controlled by the authority responsible for the location.

Statement 37

Warning

This equipment must be grounded. Never defeat the ground conductor or operate the equipment in the

absence of a suitably installed ground conductor. Contact the appropriate electrical inspection

authority or an electrician if you are uncertain that suitable grounding is available.

Statement 1024

Warning

When installing or replacing the unit, the ground connection must always be made first and

disconnected last.

Statement 1046

To complete your installation, follow these steps:

Step 1 Install the cover. Place it into position, slide it forward, and then tighten the captive screw (labeled 1 in

Figure 2).

Caution Before sliding the cover forward, make sure that the cover will properly engage the ledge at the front of

the device.

Step 2 Install the bezel, as follows:

a. Align the hooks on the bottom of the bezel with the device.

b. Press the bezel toward the device until it clicks into place.

Step 3 Install the device in the rack. See the Cisco Wide Area Application Engine 511 and 611 Hardware

Installation Guide for instructions.

Warning

To prevent bodily injury when mounting or servicing this unit in a rack, you must take special

precautions to ensure that the system remains stable. The following guidelines are provided to

ensure your safety:

• This unit should be mounted at the bottom of the rack if it is the only unit in the rack.

• When mounting this unit in a partially filled rack, load the rack from the bottom to the top with the heaviest

component at the bottom of the rack.

• If the rack is provided with stabilizing devices, install the stabilizers before mounting or servicing the unit in

the rack.

Statement 1006

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Cisco Hardware di rete

Cisco

Cisco LightStream 1010 Manuale

Cisco

Cisco ONS 15540 ESP Manuale

Cisco

Cisco TELEPRESENCE MCU ACCESSING CONFERENCES - Manuale utente

Cisco

Cisco CE-507 - Content Engine 507 Manuale utente

Cisco

Cisco Firepower 2130 Guida alla manutenzione e all'assistenza

Cisco

Cisco NM-1A-T3 - 1port Ds3 Atm Network Module Manuale utente

Cisco

Cisco NM-1FE-TX - Interface Module Ethernet Manuale utente

Cisco

Cisco IPS-4240-K9 - Intrusion Protection Sys 4240 Manuale utente

Cisco

Cisco Performance Routing Engine 5 Manuale

Cisco

Cisco Aironet 1430 Series Manuale utente

Cisco

Cisco MERAKI MX85 Series Manuale

Cisco

Cisco NCS 4206 Manuale di istruzioni

Cisco

Cisco Firepower 1010 FPR1010-NGFW-K9 Manuale

Cisco

Cisco AIR-BR1410A-A-K9 - Aironet 1410 Wireless... Guida di riferimento rapido

Cisco

Cisco CSC-C2FCIT Manuale di istruzioni

Cisco

Cisco CGR 1000 Series Manuale utente

Cisco

Cisco Secure Firewall Management Center 1700 Manuale utente

Cisco

Cisco Linksys Business Series Network Storage System... Manuale utente

Cisco

Cisco GS7000 Istruzioni operative

Cisco

Cisco ISE - Line Card ISE Manuale utente

Cisco

Cisco Meraki MX65W Manuale utente

Cisco

Cisco ATM Cable Interface Processor ACIP-SM(=) Manuale dell'operatore

Cisco

Cisco Firepower 1010 Manuale utente

Cisco

Cisco ASR 5000 Series Manuale utente

Manuali Hardware di rete popolari di altre marche

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL Manuale utente

B&B Electronics

B&B Electronics ZXT9-IO-222R2 Manuale utente

Yudor

Yudor YDS-16 Manuale utente

D-Link

D-Link ShareCenter DNS-320L Manuale utente

Samsung

Samsung ES1642dc Istruzioni per l’uso

Honeywell Home

Honeywell Home LTEM-PV Istruzioni per il montaggio

evertz

evertz 7700 Series Manuale utente

D-Link

D-Link ShareCenter DNS-343 Manuale utente

Asante

Asante AsanteBridge 1012 Manuale utente

FireBrick

FireBrick FB2700 Manuale utente

Audiovox Electronics

Audiovox Electronics ARWH2T Manuale utente

ADC

ADC DSX-1 Manuale

NetComm

NetComm NF2 Manuale utente

Alcatel-Lucent

Alcatel-Lucent 5620 Manuale utente

Dell EMC

Dell EMC XC6420 Series Manuale utente

Lanner

Lanner NCA-1020A Manuale utente

Allied Telesis

Allied Telesis AT-TN121-A Manuale utente

Arista

Arista CCA-ETM-Q12 Manuale utente