Cisco Gigabit Switch Router Cisco 12012 Manuale utente

Doc. No.

Cisco Systems, Inc.

170 West Tasman Drive

San Jose, CA 95134-1706

USA

Cisco Systems, Inc.

Corporate Headquarters

Cisco 12012 Gigabit Switch Router Cable-

Management Kit Installation Instructions

Product Numbers: ACS-GSR12-CCBLM=, ACS-GSR-LCCBLM=

Document Order Number: DOC-784346=

This document contains instructions for installing or replacing cable-management kit components in

the Cisco 12012 Gigabit Switch Router (GSR).

The sections in this document include the following:

•Product Overview, page 1

•Safety Guidelines, page 4

•Tools and Parts Required, page 5

•Removing and Replacing the Cable-Management System, page 6

•FCC Class A Compliance, page 12

•Cisco Connection Online, page 13

Product Overview

The Cisco 12012 has two card cages; the upper card cage and the lower card cage. (Refer to

Figure 1.) The upper card cage has 12 user-configurable slots available for line cards and a route

processor (RP). One additional slot (rightmost slot) in the upper card cage is non-configurable; it is

reserved for an alarm card. The line cards and the RP are not slot dependent; you can install the line

cards and the RP in any of the first 12 available slots.

78-4346-02

2Cisco 12012 Gigabit Switch Router Cable- Management Kit Installation Instructions

Product Overview

Figure 1 Cisco 12012—Front View

The lower card cage, located behind the air filter, has five horizontal slots for switch fabric cards.

Below the lower card cage is a power supply bay. Up to four AC-input power supplies or two

DC-input power supplies can be installed in the bay.

A cable-management system manages the line card interface cables in the upper card cage, keeping

them organized and free from sharp bends, which can degrade cable performance. The Cisco 12012

cable-management system consists of two components: a horizontal cable-management tray, which

is attached to the frame directly above the upper card cage, and a vertical cable-management bracket,

which is attached to each line card. (Refer to Figure 2.)

The horizontal cable-management tray keeps the interface cables organized by upper card cage slot

and free of sharp bends as the cables enter the Cisco 12012 from either the left or right side and are

routed to the individual line cards.

INPUT:

200-240V

10A

50/60HZ

2000W

OUTPUT

FAIL

INPUT:

200-240V

10A

50/60HZ

2000W

OUTPUT

FAIL

INPUT:

200-240V

10A

50/60HZ

2000W

OUTPUT

FAIL

INPUT:

200-240V

10A

50/60HZ

2000W

OUTPUT

FAIL

SLOT-0

ROUTEPROCESSOR

SLOT-1

COLL

LINKTX

RJ-45

MII

RESET

AUX

CONSOLE

EJECT

ACTIVE

CARRIER

RXPKT

ACTIVE

CARRIER

RXPKT

ACTIVE

CARRIER

RXPKT

ACTIVE

CARRIER

RXPKT

QOC-3/STM-POS

ACTIVE

CARRIER

RXCELL

OC-12/STM-4ATM

OC-12/STM-4POS

ACTIVE

CARRIER

RXCELL

ACO/LT

ALARM

CSC

FAIL

1012

ENABLED

CRITICAL

MAJOR

MINOR

SFC

ALARM1 ALARM2

H10476

Top blower module

(behind front cover)

Upper card cage

Lower card cag

(behind air filte

Frame

Air filter tray

Power supply bay

ottom blower module

(

behind front cover)

Cisco 12012 Gigabit Switch Router Cable- Management Kit Installation Instructions 3

Product Overview

Figure 2 Cisco 12012 Cable-Management System

The vertical cable-management bracket attaches to each line card with two captive screws. Rubber

clips on the vertical cable-management bracket hold the line card’s interface cables in place,

allowing installation and removal of adjacent line cards. A vertical cable-management bracket can

be detached from the line card with the interface cables still in their clips, aligned to their respective

line card ports. This speeds up a line card removal and replacement.

SLOT-0

GIGABIT ROUTE PROCESSOR

SLOT-1

COLL

LINK TX

RJ-45

MII

RESET

AUX

CONSOLE

EJECT

ACTIVE

CARRIER

RX PKT

ACTIVE

CARRIER

RX PKT

ACTIVE

CARRIER

RX PKT

ACTIVE

CARRIER

RX PKT

Q OC-3/STM-POS

ACTIVE

CARRIER

RX CELL

OC-12/STM-4 ATM

OC-12/STM-4 POS

ACTIVE

CARRIER

RX CELL

ACO/LT

ALARM 1 ALARM 2

ALARM

CSC

FAIL

1012

ENABLED

CRITICAL

MAJOR

MINOR

SFC

H10706

Captive screw

Interface

cable

Captive screw

Cutout for hook Chassis cable-management tray

Line card

able-management

bracket

Hook

4Cisco 12012 Gigabit Switch Router Cable- Management Kit Installation Instructions

Safety Guidelines

Before you begin the procedures in this document, review the safety guidelines in this section to

avoid injuring yourself or damaging the equipment.

In addition, review the safety warnings listed in the document Regulatory Compliance and Safety

Information for the Cisco 12012 Gigabit Switch Router (Document Number 78-4347-xx) that

supports your Cisco 12012 before installing, configuring, or maintaining the router.

Safety with Equipment

The following guidelines will help ensure your safety and protect the equipment. This list is not

inclusive of all potentially hazardous situations, so be alert.

•Always disconnect all power cords and interface cables before moving the card cage assembly.

•Keep tools and assembly components away from walk areas.

•Do not work alone if potentially hazardous conditions exist.

•Do not perform any action that creates a potential hazard to people or makes the equipment

unsafe.

•Carefully examine your work area for possible hazards such as moist floors, ungrounded power

extension cables, and missing safety grounds.

Safety with Electricity

The line cards, RP, switch fabric cards, alarm card, blower modules, and redundant power supplies

are designed to be removed and replaced while the system is operating without presenting an

electrical hazard or damage to the system.

Follow these basic guidelines when working with any electrical equipment:

•Before beginning any procedures requiring access to the interior of the Cisco 12012, locate the

emergency power-off switch for the room in which you are working.

•Look carefully for possible hazards in your work area, such as moist floors, ungrounded power

extension cables, and missing safety grounds.

•If an electrical accident occurs, proceed as follows:

—Use caution; do not become a victim yourself. Disconnect power to the system.

—If possible, send another person to get medical aid. Otherwise, assess the condition of the

victim and then call for help.

—Determine if the person needs rescue breathing or external cardiac compressions; then take

appropriate action.

•Disconnect all power and external cables before installing or removing a router.

•Never assume that power has been disconnected from a circuit; always check.

•Do not perform any action that creates a potential hazard to people or makes the equipment

unsafe.

•Never install equipment that appears damaged.

Cisco 12012 Gigabit Switch Router Cable- Management Kit Installation Instructions 5

Tools and Parts Required

In addition, use the guidelines that follow when working with any equipment that is disconnected

from a power source, but still connected to telephone or network wiring:

•Never install telephone wiring during a lightning storm.

•Never install telephone jacks in wet locations unless the jack is specifically designed for wet

locations.

•Never touch uninsulated telephone wires or terminals unless the telephone line has been

disconnected at the network interface.

•Use caution when installing or modifying telephone lines.

Preventing Electrostatic Discharge Damage

Electrostatic discharge damage, which can occur when electronic boards or components are handled

improperly, can result in complete or intermittent failures.

Following are guidelines for preventing ESD damage:

•Always use an ESD-preventive wrist strap or ankle strap and ensure that it makes good skin

contact.

•When removing or installing a horizontal cable-management tray or vertical cable-management

bracket, connect the equipment end of a ground strap to one of the two ESD ground sockets

located on the front sides of the upper card cage or to a bare metal surface on the frame.

•If you plan to return a replaced part to the factory, immediately place it in a static shielding bag

to avoid ESD damage to the part.

•The wrist strap only protects the part from ESD voltages on the body; ESD voltages on clothing

can still cause damage.

Caution You should periodically check the resistance value of the antistatic strap. The

measurement should be between 1 and 10 megohms.

Tools and Parts Required

You need the following tools and parts to install or replace a horizontal cable-management tray or

vertical cable-management bracket:

•3/16-inch flat-blade screwdriver

•ESD-preventive wrist strap

•A cable-management kit (Product Number ACS-GSR12-CCBLM=) or a vertical

cable-management kit (Product Number ACS-GSR-LCCBLM=)

6Cisco 12012 Gigabit Switch Router Cable- Management Kit Installation Instructions

Removing and Replacing the Cable-Management System

This section provides the procedures for removing and replacing a horizontal cable-management

tray or a vertical cable-management bracket.

Removing a Horizontal Cable-Management Tray

The horizontal cable-management tray is mounted above the upper card cage and spans the width of

the frame. It is secured to the frame with four screws. Perform the following procedure to remove

the horizontal cable-management tray:

Step 1 Attach an antistatic wrist strap to yourself and to one of the two ESD connection sockets

located on the front edges of the upper card cage or to bare metal on the frame.

Step 2 Proceeding from left to right, identify each line card and write down the following

information:

•The slot number and type of line card.

•The interface cable connections to the line card ports. You will need to reconnect the

interface cables to the same line card ports.

Step 3 Proceeding from left to right in the upper card cage, select a line card. Starting with the

bottom port on the line card and working up (for cards with multiple ports only),

disconnect the network interface cable from the line card ports. Do not remove the cables

from the vertical cable-management bracket. (Refer to Figure 2.)

Step 4 Loosen the captive screws at the top and bottom of the vertical cable-management

bracket. (Refer to Figure 2.)

Step 5 Remove the vertical cable-management bracket from the line card and remove the

attached cables from the horizontal cable-management tray. Position the vertical

cable-management bracket out of the way of the horizontal cable-management tray.

Repeat Step 3 through Step 5 for the rest of the vertical cable-management brackets on the line cards.

Step 6 Remove the four screws at the lower edge the horizontal cable-management tray. (Refer

to Figure 3.)

Step 7 Pivot the bottom of the tray out, away from the frame, to disengage three horizontal

cable-management tray tabs (at the top of the tray) from the slots in the frame.

Step 8 Remove the horizontal cable-management tray from the frame and set it aside.

Cisco 12012 Gigabit Switch Router Cable- Management Kit Installation Instructions 7

Removing and Replacing the Cable-Management System

Figure 3 Removing the Horizontal Cable-Management Tray

Installing a Horizontal Cable-Management Tray

Perform the following steps to install a replacement horizontal cable-management tray:

Step 1 Attach an antistatic wrist strap to yourself and to one of the two ESD connection sockets

located on the front edges of the upper card cage or to bare metal on the frame.

Step 2 Remove the replacement horizontal cable-management tray from its shipping packaging.

Step 3 Angle the horizontal cable-management tray so that the top of the tray goes into the front

of the frame first. Fit the three tabs at the topofthe horizontal cable-management tray into

the slots in the frame.

Step 4 Pivot the horizontal cable-management tray down so that the rest of the tray is in contact

with the frame.

Step 5 Secure the horizontal cable-management tray in the frame with the four screws.

Step 6 Consulting your list of line cards and their interface cable connections, select the vertical

cable-management bracket for the first line card (proceeding from left to right in the

upper card cage).

SLOT-0

GIGABIT ROUTEPROCESSOR

SLOT-1

COLL

LINK TX

RJ-45

MII

RESET

AUX

EJECT

ACTIVE

CARRIER

RXPKT

ACTIVE

CARRIER

RXPKT

ACTIVE

CARRIER

RXPKT

ACTIVE

CARRIER

RXPKT

Q OC-3/STM-POS

ACTIVE

CARRIER

RXCELL

OC-12/STM-4ATM

OC-12/STM-4 POS

ACTIVE

CARRIER

RXCELL

ACO/LT

ALARM

CSC

FAIL

1012

ENABLED

CRITICAL

MAJOR

MINOR

SFC

ALARM 1 ALARM 2

H10905

orizontal

able-management

ray

Tabs (3)

Screws (4)

Frame

8Cisco 12012 Gigabit Switch Router Cable- Management Kit Installation Instructions

Removing and Replacing the Cable-Management System

Step 7 Carefully place the interface cables in the horizontal cable tray and route them down

through the bottom of the horizontal cable-management tray directly over the line card

attached to the vertical cable-management bracket.

Step 8 Attach the vertical cable-management bracket to the line card and secure it in place with

the two captive screws.

Step 9 Attach the interface cables to the line card ports.

Repeat Step 6 through Step 9 for the rest of the vertical cable-management brackets.

Removing a Vertical Cable-Management Bracket

A vertical cable-management bracket attaches to each line card to organize and control the location

of interface cables. A series of rubber clips on each vertical cable-management bracket keep the

cables in place.

Perform the following steps to remove a vertical cable-management bracket:

Step 1 Attach an antistatic wrist strap to yourself and to one of the two ESD connection sockets

located on the front edges of the upper card cage or to bare metal on the frame.

Step 2 On a piece of paper, note the interface cable connections on the line card.

Cisco 12012 Gigabit Switch Router Cable- Management Kit Installation Instructions 9

Removing and Replacing the Cable-Management System

Step 3 Proceeding from the bottom port on the line card (for line cards with multiple ports only),

disconnect the network interface cable from the each port on the line card. (Refer to

Figure 4a.)

Step 4 Carefully remove the interface cable from the vertical cable-management bracket clips.

(Refer to Figure 4b.)

Step 5 Carefully remove the interface cable from the vertical cable-management bracket clip

nearest the line card port. (Refer to Figure 4c.) Set the interface cable aside.

Repeat Step 3 through Step 5 for the rest of the interface cables attached to the line card.

Figure 4 Removing the Cables From a Vertical Cable-Management Bracket

ACTIVE

CARRIER

RX PKT

ACTIVE

CARRIER

RX PKT

ACTIVE

CARRIER

RX PKT

ACTIVE

CARRIER

RX PKT

Chassis

cable-management

tray

Line card

cable-management

bracket

nterface

cable

ACTIVE

CARRIER

RX PKT

ACTIVE

CARRIER

RX PKT

ACTIVE

CARRIER

RX PKT

ACTIVE

CARRIER

RX PKT

Cable clip Cable clips

ACTIVE

CARRIER

RX PKT

ACTIVE

CARRIER

RX PKT

ACTIVE

CARRIER

RX PKT

ACTIVE

CARRIER

RX PKT

ACTIVE

CARRIER

RX PKT

ACTIVE

CARRIER

RX PKT

ACTIVE

CARRIER

RX PKT

ACTIVE

CARRIER

RX PKT

H10880

10 Cisco 12012 Gigabit Switch Router Cable- Management Kit Installation Instructions

Removing and Replacing the Cable-Management System

Step 6 Loosen the two captive screws at the top and bottom of the vertical cable-management

bracket.

Step 7 Remove the vertical cable-management bracket from the line card.

Installing a Vertical Cable-Management Bracket

If you have installed a new line card in your Cisco 12012, you need to install a vertical

cable-management bracket to keep the interface cables organized. The vertical cable-management

bracket attaches to the line card faceplate with two captive screws; the interface cables are secured

with clips.

Perform the following steps to install a vertical cable-management bracket:

Step 1 Attach an antistatic wrist strap to yourself and to one of the two ESD connection sockets

located on the front edges of the upper card cage or to bare metal on the frame.

Step 2 Attach the vertical cable-management bracket to the line card. Secure the bracket in place

with two captive screws.

Step 3 Carefullyroutethelinecardinterfacecablesupthroughthe horizontal cable-management

tray and exit the horizontal tray either to the left side or the right side.

Altri manuali per Gigabit Switch Router Cisco 12012

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Cisco Hardware di rete

Cisco

Cisco ASR 5500 Manuale di istruzioni

Cisco

Cisco NCS 2000 series Manuale utente

Cisco

Cisco Aironet 1400 Series Manuale utente

Cisco

Cisco Edge 300 Series Guida rapida

Cisco

Cisco ASR 5000 Manuale utente

Cisco

Cisco ATA 191 Manuale utente

Cisco

Cisco 2610 - Router - EN Manuale utente

Cisco

Cisco 7246 - uBR Router Manuale utente

Cisco

Cisco MA-UMNT-MR-A3 Manuale utente

Cisco

Cisco ONS 15600 Manuale utente

Cisco

Cisco Meraki MX68 Manuale

Cisco

Cisco o UCS X440p Istruzioni di installazione e manutenzione

Cisco

Cisco Cisco ONS 15600 SDH Manuale utente

Cisco

Cisco CSS11501 - 100Mbps Ethernet Load Balancing... Manuale utente

Cisco

Cisco NSS2000 Series Manuale utente

Cisco

Cisco SOURCEfire 3D500 Manuale utente

Cisco

Cisco CATALYST RPS 2300 Guida rapida

Cisco

Cisco TELEPRESENCE MCU ACCESSING CONFERENCES - Manuale utente

Cisco

Cisco 1230AG - Aironet - Wireless Access Point Manuale utente

Cisco

Cisco ASR 9000 Series Manuale utente

Cisco

Cisco ATM Cable Interface Processor ACIP-SM(=) Manuale dell'operatore

Cisco

Cisco CE-507 - Content Engine 507 Manuale utente

Cisco

Cisco ONS 15454 M12 Manuale utente

Cisco

Cisco Content Delivery Engine 100/200/300/400 Manuale

Manuali Hardware di rete popolari di altre marche

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL Manuale utente

B&B Electronics

B&B Electronics ZXT9-IO-222R2 Manuale utente

Yudor

Yudor YDS-16 Manuale utente

D-Link

D-Link ShareCenter DNS-320L Manuale utente

Samsung

Samsung ES1642dc Istruzioni per l’uso

Honeywell Home

Honeywell Home LTEM-PV Istruzioni per il montaggio

evertz

evertz 7700 Series Manuale utente

D-Link

D-Link ShareCenter DNS-343 Manuale utente

Asante

Asante AsanteBridge 1012 Manuale utente

FireBrick

FireBrick FB2700 Manuale utente

Audiovox Electronics

Audiovox Electronics ARWH2T Manuale utente

ADC

ADC DSX-1 Manuale

NetComm

NetComm NF2 Manuale utente

Alcatel-Lucent

Alcatel-Lucent 5620 Manuale utente

Dell EMC

Dell EMC XC6420 Series Manuale utente

Lanner

Lanner NCA-1020A Manuale utente

Allied Telesis

Allied Telesis AT-TN121-A Manuale utente

Arista

Arista CCA-ETM-Q12 Manuale utente