Cisco Prisma EtherLinX Manuale utente

4008226 Rev B 1

Prisma EtherLinX Unit Installation

Instructions

Overview

Introduction

The Prisma®EtherLinX™unit enables service providers to offer differentiated data

networking or virtual private network (VPN) services to multi-tenant building and

business customers. Residing at the customer premises or at the service provider

point of presence (POP), the Prisma EtherLinX unit provides a VLAN-based Layer 2

entry point to the metropolitan area network (MAN) fiber network, trunking,

differentiating and separating customer traffic. Featuring SNMP management,

bandwidth control, quality of service (QoS), traffic prioritization, and multicast

pruning (using IGMP v1, v2), it is an ideal solution for delivering Ethernet-based

services to customers quickly and cost-effectively. The Prisma EtherLinX unit also

features Telnet, and firmware upgrading through serial configuration or Telnet via a

TFTP server.

Purpose

These installation instructions provide product information and instructions for

installing the Prisma EtherLinXunit.

Continued on next page

2 4008226 Rev B

Overview, Continued

Qualified Personnel

Only appropriately qualified and trained personnel should install, operate, maintain,

and service this product.

WARNING:

Allow only qualified personnel to install, operate, maintain, and service this

product. Otherwise, personal injury or equipment damage may occur.

In These Installation Instructions

These installation instructions contain the following topics.

Topic See Page

Important Safety Instructions 3

Laser Safety 13

Product Description 16

Prisma EtherLinX Unit Installation Instructions 17

Software Configurable Features 19

About PrismaView Software 21

SNMP Management 22

Device-Specific Configuration 28

Fiber Optic Cleaning Guidelines 34

Module LED Indicators 36

For Information 37

4008226 Rev B 3

Important Safety Instructions

Read and Retain Instructions

Carefully read all safety and operating instructions before operating this equipment,

and retain them for future reference.

Follow Instructions and Heed Warnings

Follow all operating and use instructions. Pay attention to all warnings and cautions

in the operating instructions, as well as those that are affixed to this equipment.

Explanation of Warning and Caution Icons

Avoid personal injury and product damage! Do not proceed beyond any symbol

until you fully understand the indicated conditions.

The following warning and caution icons alert you to important information about

the safe operation of this product:

You may find this symbol in the document that accompanies this product.

This symbol indicates important operating or maintenance instructions.

You may find this symbol affixed to the product. This symbol indicates a

live terminal where a dangerous voltage may be present; the tip of the

flash points to the terminal device.

You may find this symbol affixed to the product. This symbol indicates a

protective ground terminal.

You may find this symbol affixed to the product. This symbol indicates a

chassis terminal (normally used for equipotential bonding).

You may find this symbol affixed to the product. This symbol warns of a

potentially hot surface.

You may find this symbol affixed to the product and in this document.

This symbol indicates an infrared laser that transmits intensity-

modulated light and emits invisible laser radiation or an LED that

transmits intensity-modulated light.

Continued on next page

4 4008226 Rev B

Important Safety Instructions, Continued

Terminology

The terms defined below are used in this document. The definitions given are based

on those found in safety standards.

Service Personnel - The term service personnel applies to trained and qualified

individuals who are allowed to install, replace, or service electrical equipment. The

service personnel are expected to use their experience and technical skills to avoid

possible injury to themselves and others due to hazards that exist in service and

restricted access areas.

User and Operator - The terms user and operator apply to persons other than service

personnel.

Ground(ing) and Earth(ing) - The terms ground(ing) and earth(ing) are synonymous.

This document uses ground(ing) for clarity, but it can be interpreted as having the

same meaning as earth(ing).

Electric Shock Hazard

Because of the potential for higher humidity, the presence of moisture, the proximity

to ground potential and the possibility that hazardous voltages may be present on

network connected cables, there is a greater risk of electric shock when working with

electronic equipment in the outdoor environment.

To minimize the likelihood and effect of electric shock, follow the instructions in this

warning and the precautions below.

WARNING!

To reduce risk of electric shock, perform only the instructions that are included

in the operating instructions. Refer all servicing to qualified service personnel

only.

•Do not work in rain, fog or snow conditions

•Ensure equipment and cables are dry

•Wear shoes with soles made of insulated material e.g. rubber, vinyl, etc.

•When making electrical connections, work with one hand in your pocket and

avoid accidental contact with grounded surfaces

•Use insulated tools to make electrical connections

•Make all other connections before connecting power to the equipment

Installation

This equipment should be installed by qualified service personnel and should

comply with national and local requirements.

Continued on next page

4008226 Rev B 5

Important Safety Instructions, Continued

Note to the Installer

Equipment Placement

WARNING:

Avoid personal injury and damage to this equipment. An unstable mounting

surface may cause this equipment to fall.

To protect against equipment damage or injury to personnel, comply with the

following:

•Place this equipment close enough to a mains AC outlet to accommodate the

length of this equipment’s power cord.

•Route all power cords so that people cannot walk on, place objects on, or lean

objects against them. This may pinch or damage the power cords. Pay particular

attention to power cords at plugs, outlets, and the points where the power cords

exit this equipment.

•Make sure the mounting surface or rack is stable and can support the size and

weight of this equipment.

Continued on next page

6 4008226 Rev B

Important Safety Instructions, Continued

Ventilation

WARNING:

Avoid electric shock and fire hazard! Never push objects through the openings

in this equipment. Foreign objects can touch dangerous voltage points or cause

electrical shorts that can result in electric shock or fire.

This equipment may have openings for ventilation that protect it from overheating.

To ensure the reliability of this equipment, do not obstruct the openings

•Do not place other equipment, lamps, books, or other objects on top of this

equipment.

•Do not place this equipment in any of the following locations.

−On a bed, sofa, rug, or similar surface

−Over a radiator or a heat register

−In an enclosure, such as a bookcase or equipment rack, unless the installation

provides proper ventilation

Handling Precautions

When moving a cart that contains this equipment, check for any of the following

possible hazards:

WARNING:

Avoid personal injury and damage to this equipment! Move

any equipment and cart combination with care. Quick stops,

excessive force, and uneven surfaces may cause this

equipment and cart to overturn.

Cleaning the Equipment

Before cleaning this equipment, unplug it from the electrical outlet. Use a damp cloth

to clean this equipment. Do not use a liquid cleaner or an aerosol cleaner. Do not use

a magnetic/static cleaning device (dust remover) to clean this equipment.

Continued on next page

4008226 Rev B 7

Important Safety Instructions, Continued

Object and Liquid Entry

Never push objects of any kind into this equipment through openings as they may

touch dangerous voltage points or short out parts that could result in a fire or electric

shock. Do not expose this equipment to liquid or moisture. Do not place this

equipment on a wet surface. Do not spill liquids on or near this equipment.

Overloading

Do not overload electrical outlets, extension cords, or integral convenience

receptacles, as this can result in a risk of fire or electric shock. For equipment that

requires battery power or other sources to operate, refer to the operating instructions

for that equipment.

Lightning and Power Surges

To protect this equipment against damage from lightning storms and power-line

surges, do the following:

•Disconnect the power cord from the grounded mains electrical outlet and

disconnect the antenna or cable system under the following circumstances.

−During lightning storms, or

−When you are not using this equipment for an extended period

•Ground your antenna system to provide some protection against voltage surges

and built-up static charge.

Power Sources

WARNING:

Avoid electric shock and fire hazard! Do not overload electrical outlet and

extension cords. For equipment that requires battery power or other sources to

operate, refer to the operating instructions for that equipment.

•A label on this equipment indicates the correct power source for this equipment.

Operate this equipment only from an electrical outlet with the voltage and

frequency indicated on the equipment label.

•If this equipment plugs into an outlet, the outlet must be near this equipment, and

must be easily accessible.

•This equipment may have two power sources. Be sure to disconnect all power

sources before working on this equipment.

Continued on next page

8 4008226 Rev B

Important Safety Instructions, Continued

•If this equipment does not have a main power switch, the power cord connector

serves as the disconnect device.

•Always pull on the plug or the connector to disconnect a cable. Never pull on the

cable itself.

•Unplug this equipment if it will be unused for long periods of time.

•If you are uncertain of the type of power supply to your home or business, consult

your local power company.

Grounding

This section provides instructions for verifying that the equipment is properly

grounded.

Safety Plugs (USA Only)

This equipment is equipped with either a 3-terminal (grounding-type) safety plug or

a 2-terminal (polarized) safety plug. The wide blade or the third terminal is provided

for safety. Do not defeat the safety purpose of the grounding-type or polarized safety

plug.

To properly ground this equipment, follow these safety guidelines:

•Grounding-Type Plug - For a 3-terminal plug (one terminal on this plug is a

protective grounding pin), insert the plug into a grounded mains, 3-terminal

outlet.

Note: This plug fits only one way. If this plug cannot be fully inserted into the

outlet, contact an electrician to replace the obsolete 3-terminal outlet.

•Polarized Plug - For a 2-terminal plug (a polarized plug with one wide blade and

one narrow blade), insert the plug into a polarized mains, 2-terminal outlet in

which one socket is wider than the other.

Note: If this plug cannot be fully inserted into the outlet, try reversing the plug. If

the plug still fails to fit, contact an electrician to replace the obsolete 2-terminal

outlet.

Continued on next page

4008226 Rev B 9

Important Safety Instructions, Continued

Grounding Terminal

If this equipment is equipped with an external grounding terminal, attach one end of

an 18-gauge wire (or larger) to the grounding terminal; then, attach the other end of

the wire to a ground, such as a grounded equipment rack.

Safety Plugs (European Union)

•Class I Mains Powered Equipment – Provided with a 3-terminal AC inlet and

requires connection to a 3-terminal mains supply outlet via a 3-terminal power

cord for proper connection to the protective ground.

Note: The equipotential bonding terminal provided on some equipment is not

designed to function as a protective ground connection.

•Class II Mains Powered Equipment – Provided with a 2-terminal AC inlet that

may be connected by a 2-terminal power cord to the mains supply outlet. No

connection to the protective ground is required as this class of equipment is

provided with double or reinforced and/or supplementary insulation in addition

to the basic insulation provided in Class I equipment.

Note: Class II equipment, which is subject to EN 50083-1, is provided with a

chassis mounted equipotential bonding terminal. See the section titled

Equipotential Bonding for connection instructions.

Equipotential Bonding

If this equipment is equipped with an external chassis terminal marked with the IEC

60471-5020 chassis icon ( ), the installer should refer to CENELEC standard EN

50083-1 or IEC standard IEC 60728-11 for correct equipotential bonding connection

instructions.

Servicing

WARNING:

Avoid electric shock! Opening or removing the cover may expose you to

dangerous voltages.

Do not open the cover of this equipment. Refer all servicing to qualified personnel

only. Contact us for instructions.

Continued on next page

10 4008226 Rev B

Important Safety Instructions, Continued

Damage that Requires Service

For damage that requires service, unplug this equipment from the electrical outlet.

Refer service to qualified service personnel when any of the following occurs:

•There is damage to the power cord or plug

•Liquid enters the equipment

•A heavy object falls on the equipment

•Operation is not normal (the instructions in this manual describe the proper

operation)

•If you drop this equipment, or damage the cabinet of this equipment

•If this equipment exhibits a distinct change in performance

Upon completion of any service or repairs to this equipment, ask the service

technician to perform safety checks to determine that the equipment is in proper

operating condition.

CAUTION:

Avoid damage to this equipment! Adjust only what the operating instructions

describe. Improper adjustment of controls may result in damage that may

require extensive corrective work by qualified service personnel.

Replacement Parts

When replacement parts are required, be sure the qualified service personnel has

used parts specified by us or have the same characteristics as the original part.

Unauthorized substitutions may result in fire, electric shock, or other hazards.

Safety Check

Upon completion of any service or repairs to this equipment, ask the service

technician to perform safety checks to determine that this equipment is in proper

operating condition.

Continued on next page

Indice

Altri manuali Cisco Hardware di rete

Cisco

Cisco ASA 5506-X Manuale

Cisco

Cisco NSS2000 - Gigabit Storage System Chassis Come usare

Cisco

Cisco CSS11501 - 100Mbps Ethernet Load Balancing... Manuale utente

Cisco

Cisco N540X-6Z18G-SYS-A Manuale utente

Cisco

Cisco IAD2430 Series Guida all'installazione

Cisco

Cisco Aironet 1430 Series Manuale utente

Cisco

Cisco ASR 5000 Manuale utente

Cisco

Cisco NTP-E157 Manuale elenco delle parti

Cisco

Cisco Aironet 1040 Series Manuale utente

Cisco

Cisco PIX Series Manuale

Cisco

Cisco 6500 - Catalyst Series 10 Gigabit EN Interface Module... Manuale utente

Cisco

Cisco CATALYST 6000 Manuale di installazione e funzionamento

Cisco

Cisco Catalyst 8300 Series Manuale

Cisco

Cisco NCS 4206 Manuale di istruzioni

Cisco

Cisco VIC-2FXS - 3600 Voice Interface Card-Fxs... Manuale di istruzioni

Cisco

Cisco Secure Firewall Management Center 1700 Manuale utente

Cisco

Cisco ONS 15454 M12 Manuale utente

Cisco

Cisco 220 Series Smart Plus Manuale utente

Cisco

Cisco ONS 15454 DWDM Manuale utente

Cisco

Cisco VSVM Manuale di istruzioni

Cisco

Cisco ONS 15310-CL Manuale utente

Cisco

Cisco IDS 4210 - Intrusion Detection Sys 4210... Manuale utente

Cisco

Cisco Secure Network Server 3700 Series Manuale

Cisco

Cisco 7246 - uBR Router Manuale utente

Manuali Hardware di rete popolari di altre marche

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL Manuale utente

B&B Electronics

B&B Electronics ZXT9-IO-222R2 Manuale utente

Yudor

Yudor YDS-16 Manuale utente

D-Link

D-Link ShareCenter DNS-320L Manuale utente

Samsung

Samsung ES1642dc Istruzioni per l’uso

Honeywell Home

Honeywell Home LTEM-PV Istruzioni per il montaggio

evertz

evertz 7700 Series Manuale utente

D-Link

D-Link ShareCenter DNS-343 Manuale utente

Asante

Asante AsanteBridge 1012 Manuale utente

FireBrick

FireBrick FB2700 Manuale utente

Audiovox Electronics

Audiovox Electronics ARWH2T Manuale utente

ADC

ADC DSX-1 Manuale

NetComm

NetComm NF2 Manuale utente

Alcatel-Lucent

Alcatel-Lucent 5620 Manuale utente

Dell EMC

Dell EMC XC6420 Series Manuale utente

Lanner

Lanner NCA-1020A Manuale utente

Allied Telesis

Allied Telesis AT-TN121-A Manuale utente

Arista

Arista CCA-ETM-Q12 Manuale utente