Cisco Edge 300 Series Manuale utente
Americas Headquarters:
Cisco Systems, Inc., 170 West Tasman Drive, San Jose, CA 95134-1706 USA
Cisco Edge 300 Series Switch Installation Guide
•
About this Guide, page 1
•
Box Contents, page 2
•
Overview, page 3
•
Installing the Switch, page 6
•
Powering on the Switch, page 15
•
Resetting to Factory Mode, page 15
•
Technical Specifications, page 15
•
Regulatory Standards Compliance, page 16
•
EMC Class A Notices and Warnings, page 17
•
Declaration of Conformity for RF Exposure, page 17
•
Obtaining Documentation and Submitting a Service Request, page 19
About this Guide
This guide describes how to install the Cisco Edge 300 series switch on a wall or desktop and describes
the LEDs and ports.
For configuration information, see the Cisco Edge 300 series switch documentation on Cisco.com. For
system requirements, important notes, limitations, open and resolved bugs, and documentation updates,
see the release notes on Cisco.com.
2
Cisco Edge 300 Series Switch Installation Guide
OL-24909-02
Box Contents
Box Contents
Note
Verify that you have received these items. If any item is missing or damaged, contact your Cisco
representative or reseller.
1Cisco Edge 300 series switch 7Four M3.5 x 16-mm Phillips head tapping
screws
1
2Power adapter 8Four plastic drywall anchors
1
3Power cord 9Cable tie
1, 2
4Power cord retainer
1, 2
1. These parts are included in the wall-mount kit (ACC-E300-WALL).
2. These parts are included in the desktop kit (ACC-E300-DESK).
10 Desktop bracket
2
5Wall-mount bracket
1
11 Two M3.0 x 6-mm Phillips pan head screws
2
6Four M3.0 x 6-mm Phillips pan head screws
1
1
2
3
4
5
6 7 8
9
10 11 9
3
Cisco Edge 300 Series Switch Installation Guide
OL-24909-02
Overview
Overview
Figure 1 Cisco Edge 300 Series Switch — Front
Figure 2 Cisco Edge 300 Series Switch — Left
Figure 3 Cisco Edge 300 Series Switch — Rear
Table 1 Cisco Edge 300 Series Models
Model Description
CS-E300-AP-K9 Cisco Edge 300 series switch with WiFi and Bluetooth
CS-E300-K9 Cisco Edge 300 series switch
HS-E300-AP-K9
1
1. This model is available only in China.
HSJC/Cisco Edge 300 series switch with WiFi and Bluetooth
HS-E300-K9
1
HSJC/Cisco Edge 300 series switch
1USB ports 5Gigabit Ethernet (uplink) port
2HDMI port 6Ethernet (downlink) ports
3Audio out port 7Power
4Audio in port
POWER
1234
GE
HDMI
255417
2
134 5 7
6
1USB port
255418
1
1Power button 2Reset button
255419
RESET
1 2
4
Cisco Edge 300 Series Switch Installation Guide
OL-24909-02
Overview
Port Descriptions
USB
There are four USB 2.0 Type-A ports. Each USB port can provide up to 5 W of power to a connected
device. You can connect a wired USB keyboard and mouse, a wireless USB receiver for a keyboard and
mouse, a USB camera, or a USB thumb drive.
HDMI
The HDMI port supports 1280x960 and 1024x768 (default) video output, and 720p and 1080p
high-definition video output.
Note
This product incorporates HDMI technology
HDMI, the HDMI Logo, and High-Definition Multimedia Interface are or registered trademarksregistered trademarks of HDMI Licensing LLC in
the United States and other countries.
Audio In
You can connect a microphone that uses a 3.5 mm connector.
Audio Out
You can connect headphones or external speakers that use a 3.5 mm connector.
Gigabit Ethernet
The Gigabit Ethernet uplink port provides a 10/100/1000 Mb/s connection to a Catalyst 2000 or
Catalyst 3000 series switch.
Ethernet
The Fast Ethernet ports provide 10/100 Mb/s connections to computers or other devices.
®
5
Cisco Edge 300 Series Switch Installation Guide
OL-24909-02
Overview
Wireless Features
WiFi
Supports 802.11b/g/n wireless clients.
Bluetooth
Supports Human Interaction Design Protocol (HIDP) for remote control or input devices.
LEDs
Figure 4 Cisco Edge 300 Series Switch LEDs
1Ethernet downlink 4Bluetooth
1
2Gigabit Ethernet uplink 5Power
3WiFi
1
1. Only CS-E300-AP-K9 and HS-E300-AP-K9.
255420
R
1234
R
12 3 4
5
5
2
13 4 5
6
Cisco Edge 300 Series Switch Installation Guide
OL-24909-02
Installing the Switch
Installing the Switch
You can install the switch on a wall by using the wall-mount bracket or install the switch on a desk or
table by using the desktop bracket. You can also install the switch in a ventilated cabinet using the
wall-mount or desktop bracket.
Equipment That You Need
•
Phillips screwdriver
•
Scratch awl or other sharp pointed object (wall-mount)
•
Electric drill with a 6-mm drill bit (wall-mount)
Ta b l e 2 L E D s
LED Color Meaning
Ethernet
downlink
Off No link.
Green Link present, no activity. Port is operating at 100 Mb/s.
Blinking green Activity. Port is sending or receiving data at 100 Mb/s.
Amber Link present, no activity. Port is operating at 10 Mb/s.
Blinking amber Activity. Port is sending or receiving data at 10 Mb/s.
Gigabit
Ethernet
Off No link.
Green Link up.
Blinking green Activity.
WiFi Off WiFi is disabled.
Green WiFi is enabled and functioning.
Blinking green WiFi is transmitting data.
Bluetooth Off Bluetooth is disabled.
Green Bluetooth is enabled and functioning.
Power Off There is no power or the self test has failed.
Green System is operating normally.
Blinking green System software is being upgraded.
Blinking amber System software download has failed.
7
Cisco Edge 300 Series Switch Installation Guide
OL-24909-02
Installing the Switch
Before You Begin
Before installing the switch, verify that these guidelines are met:
•
Front clearance so that the LEDs can be seen.
•
AC power cord reaches from the AC power outlet to the rear-panel connector.
•
Cabling is away from sources of electrical noise, such as radios, power lines, and fluorescent
lighting. Make sure that the cabling is safely away from other devices that might damage the cables.
•
Airflow around the switch is unrestricted.
•
Temperature around the unit does not exceed 104°F (40°C).
•
Humidity around the switch does not exceed 85 percent.
•
Altitude at the installation site is below 10,000 feet.
•
For Ethernet ports, cables from the switch to connected devices are not longer than 328 feet
(100 meters).
Warning Statements
Statement 1071
Statement 332
Warning
In order to comply with FCC radio frequency (RF) exposure limits, antennas should be located at a
minimum of 7.9 inches (20 cm) or more from the body of all persons.
Statement 332
Statement 1005
Warning
This product relies on the building’s installation for short-circuit (overcurrent) protection. Ensure that
the protective device is rated not greater than:
20A
Statement 1005
Warning
IMPORTANT SAFETY INSTRUCTIONS
This warning symbol means danger. You are in a situation that could cause bodily injury. Before you
work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar
with standard practices for preventing accidents. Use the statement number provided at the end of
each warning to locate its translation in the translated safety warnings that accompanied this
device.
Statement 1071
SAVE THESE INSTRUCTIONS
8
Cisco Edge 300 Series Switch Installation Guide
OL-24909-02
Installing the Switch
Statement 1019
Warning
The plug-socket combination must be accessible at all times, because it serves as the main
disconnecting device.
Statement 1019
Statement 1030
Warning
Only trained and qualified personnel should be allowed to install, replace, or service this equipment.
Statement 1030
Statement 1040
Warning
Ultimate disposal of this product should be handled according to all national laws and regulations.
Statement 1040
Statement 1044
Warning
For connections outside the building where the equipment is installed, the following ports must be
connected through an approved network termination unit with integral circuit protection:
10/100/1000 Ethernet
Statement 1044
Statement 1047
Warning
To prevent the system from overheating, do not operate it in an area that exceeds the maximum
recommended ambient temperature of:
104°F (40°C)
Statement 1047
Statement 1074
Warning
Installation of the equipment must comply with local and national electrical codes.
Statement 1074
Statement 1076
Warning
To prevent airflow restriction, allow clearance around the ventilation openings to be at least:
3 inches (7.6 cm)
Statement 1076
Caution
Be aware of the size and weight of the switch when mounting. Ensure that the mounting location has a
stable flat surface and can safely support the weight of the switch.
9
Cisco Edge 300 Series Switch Installation Guide
OL-24909-02
Installing the Switch
Installing the Switch on a Wall
Statement 378
Warning
Read the wall-mounting instructions carefully before beginning installation. Failure to use the
correct hardware or to follow the correct procedures could result in a hazardous situation to people
and damage to the system.
Statement 378
You can mount the switch horizontally or vertically on a wall.
Note
The wall-mount bracket has four slots (in two pairs) on its bottom panel (see Figure 5).
Figure 5 Bracket Slot Distances for Wall-Mounting
14.17 inches (106 mm) 26.02 inches (153 mm)
255421
1
2
10
Cisco Edge 300 Series Switch Installation Guide
OL-24909-02
Installing the Switch
Step 1
Use the four M3.0 x 6-mm Phillips pan head screws to attach the wall-mount bracket to the bottom of
the switch (see Figure 6).
Figure 6 Attaching the Wall-Mount Bracket
Step 2
Connect all the cables that are necessary for your installation.
Step 3
Slide the power cord retainer along the power cord, and snap it into the chassis (see Figure 7).
1M3.0 x 6mm Phillips pan head screws
330223
1
Altri manuali per Edge 300 Series
1
Questo manuale è adatto per i seguenti modelli
4
Indice
Altri manuali Cisco Interruttore
Cisco
Cisco Catalyst 3560-24PS Istruzioni operative e di sicurezza
Cisco
Cisco Nexus 9236C Guida rapida
Cisco
Cisco Nexus 5548UP Manuale utente
Cisco
Cisco Catalyst X6524 Guida di riferimento rapido
Cisco
Cisco Catalyst 3560-E Series Manuale utente
Cisco
Cisco CBS 350 Series Scheda tecnica
Cisco
Cisco SF220-24 Manuale di istruzioni
Cisco
Cisco Catalyst 3030 Manuale di installazione
Cisco
Cisco SG 300-20 Manuale utente
Cisco
Cisco SRW2008 - Small Business Managed Switch Manuale utente
Cisco
Cisco Catalyst X6748 Manuale utente
Cisco
Cisco Gigabit Switch Router Cisco 12012 Guida
Cisco
Cisco 2950 - Catalyst Switch Manuale di installazione
Cisco
Cisco Nexus 3548 series Manuale di installazione
Cisco
Cisco 1548M Manuale utente
Cisco
Cisco Catalyst 3560-X-24T Manuale
Cisco
Cisco Catalyst 3560-C Manuale utente
Cisco
Cisco Nexus 7000 Series Manuale di servizio
Cisco
Cisco BPX-BXM-T3-12 Manuale utente
Cisco
Cisco Meraki MS120-8 Series Manuale utente
