Cisco WAP125 Manuale utente

Altri manuali per WAP125

3

Questo manuale è adatto per i seguenti modelli

1

Altri manuali Cisco Punto di accesso wireless

Cisco

Cisco WAP131 Manuale utente

Cisco

Cisco 500 Series Manuale dell'operatore

Cisco

Cisco Small Business AP541N Manuale utente

Cisco

Cisco Aironet 3700 Series Guida di riferimento rapido

Cisco

Cisco Aironet AIR-AP1200 Manuale

Cisco

Cisco AIR-AP1041N-A-K9 Manuale utente

Cisco

Cisco MERAKI MR72 Manuale utente

Cisco

Cisco Aironet 1240AG Series Manuale utente

Cisco

Cisco Meraki MR70 Manuale utente

Cisco

Cisco AIR-AP1020 - 1000 Series Lightweight Access... Manuale utente

Cisco

Cisco 3310 Mobility Services Engine Manuale utente

Cisco

Cisco Aironet 1530 Series, 1532 Manuale utente

Cisco

Cisco WAP300N Manuale utente

Cisco

Cisco MR74 Manuale

Cisco

Cisco Linksys WAP54G LA Manuale utente

Cisco

Cisco 7200 VXR Series Manuale utente

Cisco

Cisco CISCO673-RF - 673 Router Manuale utente

Cisco

Cisco Catalyst IW6300 Series Manuale utente

Cisco

Cisco Meraki Go GR10 Manuale utente

Cisco

Cisco Aironet 1570 Series Manuale

Cisco

Cisco Aironet 2800I Series Manuale utente

Cisco

Cisco Small Business WAP551 Manuale di istruzioni

Cisco

Cisco Aironet 1520 Series Manuale

Cisco

Cisco VEN501 Manuale utente

Manuali Punto di accesso wireless popolari di altre marche

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Manuale utente

Ubiquiti

Ubiquiti NanoStation NSM2 Manuale utente

Aruba

Aruba IAP-335 Manuale utente

Advantek Networks

Advantek Networks AWN-AP-54MR Manuale utente

IP-COM

IP-COM AP355 Manuale utente

Buffalo

Buffalo AirStation WLA-L11G Manuale utente

EnGenius

EnGenius EnStationACv2 Manuale utente

D-Link

D-Link DAP-3662 Manuale utente

xG Technology

xG Technology xMax CN1300 Manuale utente

Widelink

Widelink ezWave WAP-1100 Series Manuale utente

Edimax

Edimax CAP1200 Manuale utente

Ubiquiti

Ubiquiti LBE-5AC-Gen2 Manuale utente

Aruba

Aruba AP-203R Manuale utente

LuXout Shades

LuXout Shades LUXSHADE MOTION Manuale utente

CreatComm

CreatComm TB5F Manuale utente

SineDigital

SineDigital MW-1500AP(H) Manuale utente

TP-Link

TP-Link AP9650 V1 Manuale utente

Draytek

Draytek VIGORAP 902 Manuale utente

●

●

●

●

●

●

●

Reboot and Reset the WAP125 and WAP581

to Factory Default Settings

Objective

Rebooting or restarting the Wireless Access Point (WAP) deletes the logs stored in the

volatile memory. This process is performed when certain changes in the settings need a

reboot or if the WAP is not responding or booting up properly. Resetting the WAP to factory

default settings, on the other hand, erases all configurations that have been set by the user,

and restores the device to its original settings. A reset is recommended if most of the WAP

settings need to be reconfigured.

This article aims to show you how to reboot and reset your WAP125 or WAP581 to factory

default settings.

Applicable Devices

WAP125

WAP581

Software Version

WAP125 - 1.0.0.3

WAP581 - 1.0.0.4

Reboot the Wireless Access Point

There are two ways to reboot the WAP:

Hardware reboot

Reboot through the web-based utility

Hardware Reboot

You have two ways to reboot the device hardware:

Turn the device off by pressing the POWER button while the device is connected to the power

outlet.

●

Note: The POWER button only works if the device is using a power adapter. If power is

supplied through Power over Ethernet (PoE), unplug your Ethernet connection for three

seconds then plug it back.

Press the Reset button for about three seconds only, or until the lights go off.

Note: In both above images, the WAP125 is pictured.

Reboot through the Web-based Utility

Step 1. Log in to the web-based utility of your WAP and choose Administration > Reboot.

Step 2. Click the Reboot button.

Step 3. Click OK in the confirmation window.

You should now have rebooted your device.

Schedule a Reboot

Step 1. Log in to the web-based utility of your WAP and choose Administration > Reboot.

Step 2. Check the Enable Schedule Reboot check box to configure the schedule settings.

Step 3. Choose a radio button under Schedule Reboot to determine the date and time the

●

●

WAP should reboot. The options are:

Date — Set the specific date and time a reboot should occur.

In — Set the reboot to occur from the time the function was configured. If this is chosen, skip

to Step 6.

Note: In this example, Date is chosen.

Step 4. (Optional) If Date was chosen in Step 3, click the Date field and choose the date you

want to set the WAP to reboot.

Note: In this example, 2017-06-07 is chosen.

Step 5. In the Time area, choose the hour and minute from the respective drop-down list.

The time format is in Military format.

Note: In this example, the WAP is scheduled to reboot at 3:21am on June 7, 2017.

Step 6. (Optional) If In was chosen in Step 3, from the Days drop-down list, choose the

number of days from today that the WAP should reboot.

Note: In this example, 7 is chosen.

Step 7. (Optional) From the Hours drop-down list, choose the hour of the day for the WAP to

reboot. This option is useful if you want to set a specific hour of the day for this to occur.

Note: In this example, the WAP is scheduled to reboot 7 days from now at 3 AM.

●

●

Step 8. (Optional) From the Minutes drop-down list, choose the minute in the hour for the

WAP to reboot.

Note: In this example, 0 is chosen.

Step 9. Click Save.

You should now have successfully configured a schedule for the WAP to reboot.

Reset the Wireless Access Point

There are two ways to reset the WAP to factory default settings:

Hardware reset

Reset through the web-based utility

Hardware Reset

Step 1. Press the Reset button for more than 10 seconds until the lights go off.

Step 2. Release the Reset button when the lights turn back on.

Note: In both above images, the WAP125 is pictured.

Reset through the Web-based Utility

Step 1. Log in to the web-based utility of your WAP and choose Administration > Reboot.

Step 2. Check the Restore to Factory Default Settings check box.

Step 3. Click the Reboot button.

Step 4. Click OK in the confirmation window.

You should now have reset your device to factory default settings.