Cisco WAP571 Manuale utente

●

Manually Connect a WAP571 or WAP571E to

the Network via Power Over Ethernet (PoE)

Objective

Connecting a Wireless Access Point (WAP) to the same network as your computer would allow

them to communicate, thus, allowing you to configure the WAP. This is typically done when the

WAP is to be configured for the first time, or after the WAP has been reset, and will have to be

reconfigured. This article aims to show you the steps in connecting the WAP571 or WAP571E to

the network.

Applicable Devices

WAP500 Series – WAP571, WAP571E

Software Version

1.0.0.15 – WAP571, WAP571E

Connect the WAP571 to the Network via PoE

Important: Make sure that the network you are connecting the WAP to has PoE (802.3af and

802.3at) and that your network is up and running.

Step 1. Connect one end of an Ethernet cable to the Ethernet port of a PoE switch, or router.

Step 2. Connect the other end of the Ethernet cable to the ETH0/PD port of the WAP571.

Note: WAP571 bundles the two Ethernet ports to be in link aggregation mode. If the two Ethernet

ports have been connected at the same time, the link partner must also support link aggregation.

Step 3. Check the lights on both the WAP571 and the PoE switch, or router.

Note:

An orange light on the port of the PoE switch where the WAP571 is connected indicates that

the PoE switch is powering the WAP571.

A green light on the Ethernet port of the PoE switch where the WAP571 is connected

indicates a link between the devices.

A blinking green light on the front panel of the WAP571 indicates that the device is booting up.

A solid green light indicates that the WAP571 is ready and operational.

A solid green light on the Ethernet port of the WAP571 indicates a link between the switch and

the WAP571.

A blinking green light on the Ethernet port of the WAP571 indicates that the device is

receiving and transmitting data.

You should now have connected your WAP571E to the network via PoE and can now proceed to

setting up the access point. For instructions, see Configure Basic Radio Settings on the WAP571

or WAP571E Wireless Access Point.

Connect the WAP571E to the Network via PoE

Prepare the Cabling

Step 1. Disassemble the weather-proof connector to expose the red rubber gasket. After

disassembling, you should have the following:

1 Thick rubber gasket1. Part B of the weather-proof connector2. Thin rubber gasket3. Part A of the weather-proof connector4.

Step 2. Slide the Ethernet cable through Part B of the weather-proof connector.

Step 3. Pinch the thick rubber gasket to reveal the cut and then slide the Ethernet cable through

the cut.

Step 4. Slide the Ethernet cable through Part A of the weather-proof connector.

Step 5. Insert the thin red gasket into the opening of Part B of the weather-proof connector.

Connect the WAP571E via PoE

Important: Make sure that the network you are connecting the WAP to has PoE (802.3af and

802.3at) and that your network is up and running.

Step 1. Go over the back and bottom panels of the WAP571E.

Step 2. Position the WAP571E in such a way that the label underneath the device is right side up.

Step 3. Remove the cover of the port labeled ETH0/PD to expose the Ethernet port. This can be

done by turning the cap counter-clockwise.

Note: Take care not to lose the thin rubber gasket.

Step 4. Connect the Ethernet cable into the ETH0/PD slot of the WAP571E.

Step 5. Secure the weather-proof connector by turning it clockwise on to the threaded portion of

the WAP571E.

Step 6. Insert the thick rubber gasket into Part B of the weather-proof connector.

Step 7. Secure Part A of the weather-proof connector by turning it clockwise on to the threaded

portion of Part B.

Step 8. Connect the other end of the Ethernet cable to the Ethernet port of the PoE switch.

Step 9. Check the lights on both the WAP571E and the PoE switch.

Verify the WAP571/WAP571E with PoE Connection

To verify the hardware installation, follow these instructions:

Check the cable connections.

●

Check the indicator lights.

●

Label Activity Description

Power

Off The access point is off

Solid (Green) The access point is normal; No wireless client is

connected

Solid (Blue) The access point is normal; at least one wireless

client is connected

Flashing (Blue) The access point is upgrading the firmware.

Solid (Red) The access point fails to boot with both firmware

images.

LAN

(WAP571)

Off No Ethernet link; FE Ethernet link is active or 10

Mbps.

Solid Green GE Ethernet link is active.

Flashing Green The access point is transmitting or receiving data.

You should now have connected your WAP571E to the network via PoE and can now proceed to

setting up the access point. For instructions, see Configure Basic Radio Settings on the WAP571

or WAP571E Wireless Access Point.

Altri manuali per WAP571

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Cisco Punto di accesso wireless

Cisco

Cisco Small Business WAP551 Manuale di istruzioni

Cisco

Cisco Aironet 1570 Series Manuale

Cisco

Cisco WAP125 Manuale di servizio

Cisco

Cisco WAP131 Manuale utente

Cisco

Cisco AIR-AP1251AG-A-k9 Manuale

Cisco

Cisco 800 Series Manuale utente

Cisco

Cisco Catalyst 9120AX Series Manuale utente

Cisco

Cisco Aironet 1040 Series Manuale utente

Cisco

Cisco ASA 5506-X Manuale utente

Cisco

Cisco Catalyst 9130AX Series Manuale utente

Cisco

Cisco Aironet 1600 Series Guida di riferimento rapido

Cisco

Cisco AIR-LAP1252AG-A-K9 - Aironet 1252AG - Wireless Access... Manuale utente

Cisco

Cisco 1130AG - Aironet - Wireless Access Point Manuale

Cisco

Cisco Linksys WAP54GX Istruzioni operative originali

Cisco

Cisco Meraki MR36H Manuale utente

Cisco

Cisco 1232AG - Aironet - Wireless Access Point Manuale

Cisco

Cisco Aironet 1250 Series Manuale utente

Cisco

Cisco Aironet 1500 Series Manuale utente

Cisco

Cisco AIR-CAP3502I-A-K9 Manuale utente

Cisco

Cisco Catalyst IW6300 Series Manuale

Cisco

Cisco Aironet 1520 Series Manuale

Cisco

Cisco Linksys WAP610N Manuale utente

Cisco

Cisco WAP131 Manuale utente

Cisco

Cisco Aironet 1250 Series Manuale utente

Manuali Punto di accesso wireless popolari di altre marche

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Manuale utente

Ubiquiti

Ubiquiti NanoStation NSM2 Manuale utente

Aruba

Aruba IAP-335 Manuale utente

Advantek Networks

Advantek Networks AWN-AP-54MR Manuale utente

IP-COM

IP-COM AP355 Manuale utente

Buffalo

Buffalo AirStation WLA-L11G Manuale utente

EnGenius

EnGenius EnStationACv2 Manuale utente

D-Link

D-Link DAP-3662 Manuale utente

xG Technology

xG Technology xMax CN1300 Manuale utente

Widelink

Widelink ezWave WAP-1100 Series Manuale utente

Edimax

Edimax CAP1200 Manuale utente

Ubiquiti

Ubiquiti LBE-5AC-Gen2 Manuale utente

Aruba

Aruba AP-203R Manuale utente

LuXout Shades

LuXout Shades LUXSHADE MOTION Manuale utente

CreatComm

CreatComm TB5F Manuale utente

SineDigital

SineDigital MW-1500AP(H) Manuale utente

TP-Link

TP-Link AP9650 V1 Manuale utente

Draytek

Draytek VIGORAP 902 Manuale utente