Clarke CDS2 Manuale

DRILL STAND

Model No. CDS2

Thank you for purchasing this CLARKE Drill Stand

Please read this leaflet to ensure the Stand is assembled correctly in

order that it will provide you with long and satisfacyory service.

GUARANTEE

This product is guaranteed against faulty manufacture for a period of 12

months from the date of purchase. Please keep your receipt as proof of

purchase.

This guarantee is invalid if the product is found to have been abused or

tampered with in any way, or not used for the purpose for which it was

intended.

Faulty goods should be returned to their place of purchase, no product

can be returned without prior permission.

This guarantee does not effect your statutory rights.

Fig.1

Insert the Column into the base and secure

with the two screws using a hex wrench (not

supplied)

Slide the head on to the column and secure

to the column at any convenient position.

IMPORTANT!

Secure the base to a workbench or sturdy

table using M8 bolts (not supplied). Drill the

workbench/table accordingly, using the

two mounting holes as templates.

ASSEMBLY

Fig.2

• An electric drill with a standard 43mm

neck may be secured to the head using

the locking Lever shown in Fig.2.

A 38mm reducing collar, is provided

(shown in Fig.1), allowing a drill with a

38mm collar also to be accommodated.

• The head/drill may be positioned at any

height on the column, by use of the

Head Locking Lever, shown in Fig.2.

Screw IN to secure, screw OUT to release.

• The depth of travel of the drill may be

adjusted using the adjuster shown in

Fig.2. Turn to adjust. A scale with pointer

is also provided so that accurate depths

may be set

A quick release is provided. Press the

button IN and raise or lower the adjuster

as required. Release the button to lock.

A pointer with scale is provided so that

accurate depths may be drilled.

• A quick release is also provided for the

vice jaw adjustment. Press the red

button whilst pushing IN or pulling OUT

the handle.

• Secure the vice to the base using the

two bolts provided.

To position the vice further away from the column, slacken the two securing bolts (do

not undo completely) and manouvre the vice so that the bolts (with nuts attached)

may be withdrawn through the large holes at the end of the slots in the base.

Reposition the vice so that the bolts with nuts enter the holes at the opposite ends of

the slots in the base, and position as required.

Finally, tighten the securing bolts.

Parts and Service Contacts

For Spare Parts and Service, please contact your nearest dealer,

or CLARKE International, on one of the following numbers.

PARTS & SERVICE TEL: 020 8988 7400

PARTS & SERVICE FAX: 020 8558 3622

or e-mail as follows:

PARTS: [email protected]

SERVICE: [email protected]

Indice

Altri manuali Clarke Trapano

Clarke

Clarke X-Pro CAT207 Manuale di installazione e funzionamento

Clarke

Clarke 3110835 Manuale di installazione e funzionamento

Clarke

Clarke CAT116 Manuale di istruzioni

Clarke

Clarke CAT87 Manuale di installazione e funzionamento

Clarke

Clarke CCD30LIC Manuale di istruzioni

Clarke

Clarke 6479500 Manuale di installazione e funzionamento

Clarke

Clarke Air CAT107 Manuale di istruzioni

Clarke

Clarke CAT61 Manuale di installazione e funzionamento

Clarke

Clarke CHD820 Manuale di istruzioni

Clarke

Clarke Metalworker CMD1225C Manuale di installazione e funzionamento

Clarke

Clarke Air CAT68 Manuale di istruzioni

Clarke

Clarke CAT27B Manuale di installazione e funzionamento

Clarke

Clarke CMD300 Manuale di istruzioni

Clarke

Clarke CMD300 Manuale

Clarke

Clarke CDS1 Manuale utente

Clarke

Clarke CAT60 Manuale di installazione e funzionamento

Clarke

Clarke CHD850B Manuale di istruzioni

Clarke

Clarke CON18LI Manuale di istruzioni

Clarke

Clarke Air CAT214 Manuale di installazione e funzionamento

Clarke

Clarke X-pro CAT158 Manuale di installazione e funzionamento

Clarke

Clarke CRD1250 Manuale utente

Clarke

Clarke Contractor CON24 Manuale di installazione e funzionamento

Clarke

Clarke CDD20Li Manuale di istruzioni

Clarke

Clarke Contractor CON1500RDV Manuale di istruzioni

Manuali Trapano popolari di altre marche

Makita

Makita BDF456 Manuale utente

Black & Decker

Black & Decker LDX220 Manuale utente

Hitachi

Hitachi DH 40MA Manuale utente

Challenge

Challenge JO Manuale tecnico di riferimento

Makita

Makita LXFD01 Manuale utente

Festool

Festool T18+3 Manuale utente

Milwaukee

Milwaukee M12 FPDX-202X Manuale utente

EINHELL

EINHELL TE-RH 32 E Manuale utente

Makita

Makita DHP484 Manuale utente

Makita

Makita FD05 Manuale utente

Bosch

Bosch PSB 530 RA Manuale utente

Maximum

Maximum 054-1359-4 Manuale utente

Makita

Makita HP332D Manuale utente

Raider

Raider RDP-HD31H Manuale utente

Bort

Bort BPM-1400x2 Manuale utente

Black & Decker

Black & Decker 7266 Manuale utente

KENT USA

KENT USA TRD1230 Manuale utente

Bosch

Bosch GSB 19-2 RE Manuale utente