Clarke CONTRACTOR CON1200RD Manuale di istruzioni
OPERATION & MAINTENANCE
INSTRUCTIONS
DL1021 - ISS 5
ORIGINAL INSTRUCTIONS
ROTARY HAMMER DRILL
MODEL NO: CON1200RD
PART NO: 6479600
2
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com
INTRODUCTION
Thank you for purchasing this CLARKE Hammer Drill. The CON1200RD is
designed for general drilling/masonry drilling/chiselling/drill & hammer use in
light industrial applications.
Before attempting to use this product, please read this manual thoroughly and
follow the instructions carefully. In doing so you will ensure the safety of yourself
and that of others around you, and you can look forward to your purchase
giving you long and satisfactory service.
GUARANTEE
This product is guaranteed against faulty manufacture for a period of 12
months from the date of purchase. Please keep your receipt which will be
required as proof of purchase.
This guarantee is invalid if the product is found to have been abused or
tampered with in any way, or not used for the purpose for which it was
intended.
Faulty goods should be returned to their place of purchase, no product can
be returned to us without prior permission.
This guarantee does not effect your statutory rights.
INVENTORY
1 Moulding plastic carrying case 7 Pot of Grease
2 Rotary Hammer Drill 8 8mm SDS+ masonry drill bit
3 Front Handle 9 10mm SDS+ masonry drill bit
4 13 mm Drill Chuck Adaptor 10 12mm SDS+ masonry drill bit
5 Chuck Key 11 2 x SDS+ plus masonry chisel bits
6 Dust Shield Cup
3
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com
SAFETY PRECAUTIONS
WORK AREA
1. Keep work area clean and well lit. Cluttered and dark areas invite
accidents.
2. Do not operate power tools in explosive atmospheres, such as in the
presence of flammable liquids, gases or dust. Power tools create sparks
which may ignite the dust or fumes.
3. Keep children and bystanders away while operating a power tool.
Distractions can cause you to lose control.
ELECTRICAL SAFETY
1. Avoid body contact with earthed or grounded surfaces such as pipes,
radiators, ranges or refrigerators. There is an increased risk of electric shock
if your body is earthed or grounded.
2. Do not expose power tools to rain or wet conditions. Water entering a
power tool will increase the risk of electric shock.
3. When operating a power tool outdoors, use an extension cord suitable for
outdoor use. Use of a cord suitable for outdoor use reduces the risk of
electric shock.
PERSONAL SAFETY
1. Stay alert, watch what you are doing and use common sense when
operating a power tool. Do not use a power tool while you are tired or
under the influence of drugs, alcohol or medication. A moment of
inattention while operating power tools may result in personal injury.
2. Use safety equipment. Always wear eye protection. Safety equipment such
as dust mask, non-skid safety shoes, or hearing protection used for
appropriate conditions will reduce personal injuries.
3. Avoid accidental starting. Ensure the switch is in the off position before
connecting to the power supply.
4. Do not overreach. Keep proper footing and balance at all times. This
enables better control of the power tool in unexpected situations.
WARNING: READ ALL INSTRUCTIONS. FAILURE TO FOLLOW ALL
INSTRUCTIONS LISTED BELOW MAY RESULT IN ELECTRIC SHOCK, FIRE AND/
OR SERIOUS INJURY. THE TERM “POWER TOOL” IN ALL WARNINGS LISTED
BELOW REFERS TO YOUR HAMMER DRILL.
4
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com
5. Dress properly. Do not wear loose clothing or jewellery. Keep your hair,
clothing and gloves away from moving parts. Loose clothes, jewellery or
long hair can be caught in moving parts.
POWER TOOL USE AND CARE
1. Do not force the power tool. Use the correct power tool for your
application. The correct power tool will do the job better and safer at the
rate which it was designed.
2. Do not use the power tool if the switch does not turn it on and off. Any
power tool that cannot be controlled with the switch is dangerous and
must be repaired.
3. Disconnect the battery before making any adjustments, changing
accessories, or storing power tools. Such preventive safety measures
reduce the risk of starting the power tool accidentally.
4. Store idle tools out of the reach of children and do not allow persons
unfamiliar with the power tool or these instructions to operate the power
tool. Power tools are dangerous in the hands of untrained users.
5. Maintain power tools. Check for misalignment or binding of moving parts,
breakage of parts and any other condition that may affect the power tools
operation. If damaged, have the power tool repaired before use. Many
accidents are caused by poorly maintained power tools.
6. Keep cutting tools sharp and clean. Poorly maintained cutting tools with
sharp cutting edges are less likely to bind and are easier to control.
7. Use the power tool and accessories in accordance with these instructions
and in the manner intended for the particular type of power tool, taking
into account the working conditions and the work to be performed. Use of
the power tool for operations different from intended could result in a
hazardous situation.
SERVICE
1. Have your power tool serviced by a qualified repair person using only
identical replacement parts. This will ensure that the safety of the power
tool is maintained.
5
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com
SAFETY SYMBOLS
ENVIRONMENTAL RECYCLING POLICY
Through purchase of this product, the customer is taking on the
obligation to deal with the WEEE in accordance with the WEEE
regulations in relation to the treatment, recycling & recovery and
environmentally sound disposal of the WEEE.
In effect, this means that this product must not be disposed of with general
household waste. It must be disposed of according to the laws governing
Waste Electrical and Electronic Equipment (WEEE) at a recognised disposal
facility.
Read instruction
manual before use
Wear dust mask
Class 2 Double
Insulated
Wear ear defenders
CE Mark Wear safety glasses
Weee Directive
6
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com
ELECTRICAL CONNECTIONS
Before switching the product on, make sure that the voltage of your electricity
supply is the same as that indicated on the rating plate. Connecting it to any
other power source may cause damage.
If it is necessary to change the fuse in the plug, the fuse cover must be refitted.
If the fuse cover becomes lost or damaged, the plug must not be used until a
suitable replacement is obtained.
If the plug has to be changed due to damage, a replacement should be
fitted, following the wiring instructions shown below. The old plug must be
disposed of as insertion into a mains socket could cause an electrical hazard.
If the colours of the wires in the power cable of this product do not correspond
with the markings on the terminals of your plug, proceed as follows.
• The wire which is
coloured Blue must be
connected to the
terminal which is
marked Nor coloured
Black.
• The wire which is
coloured Brown must
be connected to the
terminal which is
marked Lor coloured
Red.
We strongly recommend that this machine is connected to the mains supply via
a Residual Current Device (RCD)
If in any doubt, consult a qualified electrician. DO NOT attempt any repairs
yourself.
This symbol indicates that this is a Class II product, and does not require
an earth connection.
WARNING: READ THESE ELECTRICAL SAFETY INSTRUCTIONS
THOROUGHLY BEFORE CONNECTING THE PRODUCT TO THE MAINS
SUPPLY.
WARNING: THE WIRES IN THE POWER CABLE OF THIS PRODUCT ARE
COLOURED IN ACCORDANCE WITH THE FOLLOWING CODE:
BLUE = NEUTRAL BROWN = LIVE
Plug must be BS1363/A approved.
Always fit
Ensure that the outer sheath of
Neutral
(Blue)
Live
(Brown)
a 13 Amp
the cable is firmly held by the clamp
fuse
7
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com
OVERVIEW
NO DESCRIPTION NO DESCRIPTION
1 SDS+ Chuck 5 Rear Handle
2 Rotation Stop Switch 6 Hammer Action Selector
3 Grease Port Cover 7 Motor
4 Trigger 8 Front Handle
8
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com
BEFORE USE
INSERTING A DRILL BIT / CHISEL
The chuck clamps SDS+ drill bits and chisels without the need for a chuck key.
1. Pull back the collar.
2. Insert the bit
3. Turn the bit in the chuck until it
latches.
4. Release the collar to lock in
place.
5. Check by pulling the bit to see if it
is locked in place.
IMPORTANT: Always clean the shaft
of the drill bit before inserting into the chuck.
IMPORTANT: Do not allow dust or debris inside the chuck as this will cause
problems in the future.
REMOVING A BIT
1. Slide the collar to the rear and pull the bit out of the chuck.
USING THE DRILL CHUCK ADAPTOR (DRILL MODE ONLY)
When drilling with non SDS+ drill bits, a
13mm chuck (supplied) can be
inserted into the SDS+ chuck as
shown.
IMPORTANT: DO NOT USE THE CHUCK
ADAPTER IN HAMMER ACTION MODE.
CAUTION: WHEN REMOVING A BIT FROM THE DRILL, REMEMBER THAT IT
MAY BE EXTREMELY HOT. EITHER ALLOW IT TO COOL DOWN FIRST OR USE
INDUSTRIAL GLOVES TO REMOVE THE BIT.
9
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com
POSITIONING THE FRONT HANDLE
The front handle can be positioned
left, right or centre as required.
1. Loosen the handle by twisting it
clockwise (when viewed from
above).
2. Rotate the handle to the required
position.
3. Secure the handle by twisting it
anticlockwise (when viewed from
above).
SELECTING THE OPERATING MODE
HAMMER ACTION SELECTOR
1. With the drill not operating, set the
hammer action selector to the
required setting.
• Left - Hammer Assisted Drilling
• Right - Drill Only
IMPORTANT: When using the
“hammer action” you only need to
apply light pressure. Too much
pressure will place unnecessary load on the motor. Check the drill bits
regularly, re-sharpen or replace if required.
Mode Hammer Action selector Rotation selector
Drill Only Drill Only ON
Hammer Drill Hammer Assisted Drilling ON
Hammer only (no rotation) Hammer Assisted Drilling OFF
10
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com
ROTATION ON/OFF SELECTOR
Some jobs require the chuck to
remain stationary yet still have the
hammer effect, such as chiselling
concrete, plaster etc.
• Set the rotation selector to the
right for “no rotation”.
• Set the rotation selector to the
left for “normal rotation”.
Questo manuale è adatto per i seguenti modelli
1
Indice
Altri manuali Clarke Trapano
Clarke
Clarke 6479500 Manuale di installazione e funzionamento
Clarke
Clarke Contactor CON1200 Manuale di installazione e funzionamento
Clarke
Clarke X-pro CAT158 Manuale di installazione e funzionamento
Clarke
Clarke CAT60 Manuale di installazione e funzionamento
Clarke
Clarke CMD300 Manuale di istruzioni
Clarke
Clarke SCD28 Manuale utente
Clarke
Clarke Contractor CON18NI Manuale di istruzioni
Clarke
Clarke Air CAT107 Manuale di istruzioni
Clarke
Clarke RAD1 Manuale utente
Clarke
Clarke CBM1-B Manuale di installazione e funzionamento
Clarke
Clarke CHD500 Manuale di installazione e funzionamento
Clarke
Clarke CMD300 Manuale
Clarke
Clarke CHT599 Manuale utente
Clarke
Clarke CHD850B Manuale di istruzioni
Clarke
Clarke 3110835 Manuale di installazione e funzionamento
Clarke
Clarke CAT27B Manuale di installazione e funzionamento
Clarke
Clarke CONTRACTOR CON400RHD Manuale di istruzioni
Clarke
Clarke CRD1250 Manuale utente
Clarke
Clarke CON1500RHD Manuale di istruzioni
Clarke
Clarke Metalworker CMD10 Manuale
