Clarke CRD1250 Manuale utente

USER INSTRUCTIONS

Model No: CRD1250

Part No: 6482015

0306

SDS PLUS 1250W

ROTARY HAMMER DRILL

SDS PLUS 1250W

ROTARY HAMMER DRILL

This CLARKE product is guaranteed against faulty manufacture for a period

of 12 months from the date of purchase. Please keep your receipt as proof

of purchase.

This guarantee is invalid if the product is found to have been abused or

tampered with in any way, or not used for the purpose for which is was

intended.

Faulty goods should be returned to their place of purchase, no product

can be returned to us without prior permission.

This guarantee does not effect your statutory rights.

Thank you for purchasing this CLARKE SDS Plus 1250W Rotary Hammer Drill,

which is designed for light industrial use only.

Please read this instruction leaflet thoroughly and follow the instructions carefully,

in doing so you will ensure the safety of yourself and that of others around you, this

will also ensure that the SDS Plus 1250W Rotary Hammer Drill will give you long and

satisfactory service.

Please keep these instructions in a safe place for future reference.

CLARKE GUARANTEE

Guarantee ....................................................................................................... 1

General Safety Precautions ........................................................................... 2

Additional Safety Precautions ....................................................................... 3

Electrical Connections ................................................................................... 4

Technical Specification .................................................................................. 5

Package Contents ......................................................................................... 6

General View .................................................................................................. 7

Setup & Operation.......................................................................................... 7

Maintenance .................................................................................................. 9

Parts Diagram ................................................................................................ 10

Parts List .......................................................................................................... 11

Hand Arm Vibration Explanation ................................................................ 12

Declaration of Conformity ........................................................................... 13

Please Note that details and specifications herein, are correct of time of going to print.

However CLARKE International reserve the right to change specifications at any time without prior notice.

CONTENTS

Waste electrical products should not be disposed of with household waste. Please dispose of at your local

recycling facility.

- 1 -

WARNING:

PLEASE READ ALL INSTRUCTIONS CAREFULLY BEFORE OPERATING

As with all machinery, there are certain hazards involved with their

operation and use. Exercising respect and caution will considerably lessen

the risk of personal injury. However, if normal safety precautions are

overlooked or ignored, personal injury to the operator or damage to

property, may result.

GENERAL SAFETY PRECAUTIONS

•ALWAYS Learn the machines applications, limitations and specific potential

hazards peculiar to it. Read and become familiar with the entire operating manual.

•ALWAYS use a face or dust mask if operation is dusty.

•ALWAYS check for damage before use , any damaged part should be checked

to ensure that it will operate properly and perform it’s intended function. Check

for alignment of moving parts, breakage of parts, mountings, and any other

condition which may effect the machines operation. Any damage should

be properly repaired or the part replaced . If in any doubt DO NOT use the

machine. Consult your local dealer.

•ALWAYS disconnect the tool/machine from the power supply before servicing

and when changing accessories.

•ALWAYS wear safety goggles, manufactured to the latest European safety

standards. Everyday glasses do not have impact resistant lenses, they are NOT

safety glasses.

•ALWAYSwear ear protectors to protect your hearing.

•ALWAYS keep work area clean. cluttered areas and benches invite accidents.

•ALWAYS ensure that adequate lighting is available. A minimum intensity of 300

lux should be provided. Ensure the lighting is placed so you will not be working

in your own shadow.

•ALWAYS keep children away. All visitors should be kept at a safe distance

from the work area, especially whilst operating the machine.

•ALWAYS maintain machine in top condition. Keep tools/machines clean for

best performance. Follow maintenance instructions.

•ALWAYS handle with extreme care, do not carry the tool/machine by it’s

electrical cable, or yank the cable to disconnect it from the power supply.

•ALWAYS concentrate on the job at hand, no matter how trivial it may seem. Be

aware that accidents are caused by carelessness due to familiarity.

•ALWAYS wear proper apparel. Loose clothing or jewellery may get caught in

moving parts. Wear protective hair covering to contain long hair.

- 2 -

•ALWAYS keep your proper footing and balance at all times DO NOT over

reach. For best footing wear rubber soled footwear. Keep floor clear of oil,

scrap wood etc.

•ALWAYS use recommended accessories, the use of improper accessories could

be hazardous.

•ALWAYS remove plug from the electrical outlet when adjusting, changing parts,

or when working on the machine.

•NEVER operate the machine when under the influence of drugs, alcohol or

any medication.

•NEVER leave the machine running unattended. Turn power OFF. Do not leave

the machine until it comes to a complete stop.

•NEVER force the machine, it will do a better and safer job at the rate for which

it was designed.

•NEVER use power tools in damp or wet locations or expose them to rain. Keep

your work area well illuminated. Do NOT use in explosive atmosphere (around

paint, flammable liquids etc.). Avoid dangerous environments.

• To reduce the risk of electric shock use a suitable RCD (residual current

device).

GENERAL SAFETY PRECAUTIONS CONTINUED

ADDITIONAL PRECAUTIONS FOR POWERTOOLS

•ALWAYScheck that the chisel or drill bit is properly locked into the chuck

BEFORE starting work and that it is appropriate for the material being cut.

•ALWAYSsecure all work sufficiently using a vice or clamps. Do not use hands to

secure work as this would be extremely dangerous.

•ALWAYSswitch the machine OFF immediately the task is completed, and

remove any chisel or drill bits.

•ALWAYS check that all adjusters, chuck keys and wrenches have been

removed BEFORE turning the tool on.

•ALWAYSensure safety devices are in place and are working correctly, if not

DO NOT use the machine until rectified.

• DO NOT use the machine if the electrical cable, plug or motor is in poor

condition.

• DO NOT allow the ventilation slots in the machine to become blocked.

• DO NOT touch the drill bit or chisel immediately after use, allow time to cool.

•AVOID accidental starting, by switching off and isolating from the main

electrical supply by removing the plug from the socket when not in use.

- 3 -

ELECTRICAL CONNECTIONS

This product is provided with a standard 13 amp, 230 volt (50Hz) BS1363 plug, for

connection to a standard, domestic electrical supply. Should the plug need

replacing at any time, ensure that a plug of identical specification is used.

IMPORTANT!:

If this appliance is fitted with a plug which is moulded on to the electrical cable

(i.e. non-rewireable) please note:

• The plug MUST be thrown away if it is cut from the electric cable. There is a

danger of electric shock if it is subsequently inserted into a socket outlet.

• NEVER use the plug without the fuse cover fitted.

• Should you wish to replace a detached fuse carrier, ensure that the correct

replacement is used (as indicated by marker or colour code).

• The fuse in the plug MUST be replaced with one of the same rating (13amps)

and this must be approved to BS1362.

IMPORTANT!:

If in any doubt, do not attempt any electrical repair yourself. Consult a qualified

technician.

IMPORTANT!:

Always use an approved cable extension suitable for the power rating of this tool

(see specifications), the conductor size should also be at least the same size as the

machine, or larger. When using a cable reel, ALWAYS unwind the cable completely.

WARNING:

This appliance is double insulated.

Should it ever be necessary to change the plug, the wires in the

mains lead should be wired according to the following colour code:

BLUE - NEUTRAL

BROWN - LIVE

• Connect the BLUE coloured wire to the plug terminal marked with a

letter ‘N’ or coloured BLACK.

•

Connect the BROWN coloured wire to the plug terminal marked with

a letter ‘L’ or coloured RED.

- 4 -

TECHNICAL SPECIFICATION

Description:

Model No: .......................................................................................... CRD1250

Part No: ............................................................................................... 6482015

Product Specification:

Typical applications: ................ General Drilling/Masonry Drilling/Chiselling

Operating modes: .......................................... Drill/Hammer/Drill & Hammer

Drill type: ................................................................... SDS Plus & 3 Jaw Chuck

Chuck Capacity: .............................................................. (Ømm)1.3 - 13mm

Rotational Speed: .............................................................................. 800 RPM

Impact Rating:...................................................................... (blows/min)3200

Impact Energy: ....................................................................................... (J)3.5J

Maximum drilling diameter:

Steel: .................................................................................................... Ø 13mm

Concrete:............................................................................................ Ø 32mm

Wood: .................................................................................................. Ø 40mm

Duty cycle classification: .............................................................. Continuous

Product use classification:....................................................... Light Industrial

Noise Emissions:

Sound Power Measured: Hammer Drill: ......... 87.0 dB L

Hammer Only: ....... 98.0 dB L

Sound Power Guaranteed: Hammer Drill: ......... 98.0 dB L

Hammer Only: ..... 106.0 dB L

Vibration Emissions:

Measured Emission:(RMS)(a)(m/s) ....................................................... 3.5m/s

(refer to page 12 for hand arm vibration explanation)

Motor:

Operating voltage and frequency: ........................................... 230V ~ 50Hz

Input Wattage @ 230V Typical load: .................................................. 1250W

Input Ampere @ 230V Typical load: ....................................................... 5.4A

Supply Cable Assembly:

Length: ...................................................................................................... 2.0M

Fuse Rating: ................................................................................................ 13A

Dimensions & Weights:

Product:(length x height x width)(mm) .................................. 390 x 277 x 93

Carton size:(length x height x width)(mm) ........................... 470 x 370 x 140

Weight: (packed) .................................................................................... 9.0Kg

Weight: (unpacked) ............................................................................. 7.32Kg

- 5 -

PACKAGE CONTENTS

745

9141310111215 6 8 3 2

Fig.1

1. Black moulded plastic carry case (not shown) .............................. x1

2. Rotary hammer drill ........................................................................... x1

3. Auxiliary handle .................................................................................. x1

4. Drill chuck (1.3mm - 13mm) .............................................................. x1

5. Chuck key........................................................................................... x1

6. Dust cap ............................................................................................. x1

7. Spare set of brushes ........................................................................... x1

8. Pot of grease ...................................................................................... x1

9. Black moulded bit case .................................................................... x1

10. 8mm SDS plus masonry drill bit .......................................................... x1

11. 10mm SDS plus masonry drill bit ........................................................ x1

12. 12mm SDS plus masonry drill bit ........................................................ x1

13. SDS plus masonry chisel bits .............................................................. x2

14. Depth rod ........................................................................................... x1

15. Wrench ................................................................................................ x1

16. Operators manual. (not shown) ....................................................... x1

- 6 -

GENERAL VIEW

SETUP AND OPERATION

1. BEFORE STARTING WORK:

•Before drilling into walls and floors etc., check first that there are no hidden

electrical cables, gas or water pipes etc.

• Check the mains voltage before plugging in and switching on.

2. FITTING AND CHANGING TOOLS:

• Clean tools, and apply a thin film of grease before fitting.

• Pull back the fastening sleeve and hold, push and rotate the dust free tool

into the tool holder as far as it will go, release the fastening sleeve, the tool

will then be locked in automatically.

• Check the tool is locked in securely by attempting to pull the tool out.

3. REMOVING TOOLS:

• Ensure the drill has completely stopped and is disconnected from the

electrical supply.

• Pull back the fastening sleeve and hold, pull the tool out of the tool holder

and store safely.

NOTE: for your protection, if the tool is hot, either allow it to cool down first or

use industrial gloves to remove the tool.

Fig. 2

12 4

6789

11 3

1. Dust Guard

2. Fastening Sleeve

3. Switch Trigger

4. Handle Attachment

5. Rear Cover

6. Depth Stop

7. Hammer Control

8. Drill Control

9. Lock Pin

10. Off-Lock Knob

11. Grease Cover

- 7 -

4. STARTING WORK:

•Ensure the work area is as hazard free as

possible.

• Select and install the tool to be

used,(see paragraph 2).

• If required set the depth stop and adjust

the support handle attachment for the

most comfortable position, (see fig.3). To

install the depth stop loosen the support

handle by turning it anticlockwise. Insert

the depth stop rod through the hole in the

support handle and set to the required

depth, adjust the position of the handle

attachment if required and secure in

place by re-tightening the support

handle.

• For safety, always use the hammer drill

with the handle attached.

• Set the required mode, (see paragraph 5).

•When drilling vertically overhead, fit the rubber

dust collector onto the drill (see fig.4).

• Position the tool against the surface to be drilled,

depress the OFF lock knob (10) and then squeeze

the trigger switch (3).

NOTE: if using the hammer action DO NOT start

the drill until the tool is in contact with the

surface to be drilled/chiselled etc.

5. DRILL MODE SELECTION

• HAMMER STOP:

Your drill is equipped with a hammer stop facility for smoother drilling. To select

this mode turn the hammer control switch (7) to the position marked: .

Depress the lock pin (9) then turn the drill control (8) so that the position marked:

coincides with the arrow on the machines case.

Fig.3

SETUP AND OPERATION CONTINUED

Fig.4

- 8 -

SETUP AND OPERATION CONTINUED

• DRILL STOP:

For chiselling it is necessary to deactivate the drilling action as follows:

Turn the hammer control switch (7) to the position marked: .

Depress the lock pin (9) then turn the drill control (8) so that the position marked:

coincides with the arrow on the machines case.

• HAMMER AND DRILL:

To activate the hammer and drill mode turn the hammer control switch (7)

to the position marked: . Depress the lock pin (9) and turn the drill

control (8) so that the position marked: coincides with the arrow on the

machines case.

IMPORTANT!

When hammer drilling you only need to apply light pressure. Too much

pressure will place unnecessary load on the motor. Check the drill bits

regularly, re-sharpen or replace.

MAINTENANCE

• ALWAYS ensure the tool is isolated from the electrical supply, by switching

OFF and removing the plug from the 13 amp socket before commencing

any maintenance activities or adjustments etc.

• Clean the tool regularly, use a soft brush and or soft cleaning cloth. DO NOT

use any chemicals or harsh abrasives to clean the tool.

• At the end of work, to prevent dust deposits you should use a compressed

air (max.3 bar) to clean out the ventilation holes.

• Remove and inspect the carbon brushes regularly, it is very important to refit

the motor brushes exactly as they are removed, DO NOT turn them around

or swap their positions (dirty or worn carbon brushes result in excessive

sparking and speed faults).

• Always replace the motor brushes in pairs.

• Check gearbox regularly and top up if necessary with a good quality high

melting point gearbox grease. DO NOT overfill the gearbox, apply sufficient

grease to cover all visible moving parts. (fig.2 refers to grease cover).

WARNING: The use of spare parts or accessories, other than those supplied

by CLARKE international or one of its recognised dealers, may be

hazardous and could invalidate the guarantee.

- 9 -

Altri manuali per CRD1250

Indice

Altri manuali Clarke Trapano

Clarke

Clarke CCD30LIC Manuale di istruzioni

Clarke

Clarke CBM1-B Manuale di installazione e funzionamento

Clarke

Clarke X-Pro CAT207 Manuale di installazione e funzionamento

Clarke

Clarke CON1500RHD Manuale di istruzioni

Clarke

Clarke CRD1250 Manuale di istruzioni

Clarke

Clarke CONTRACTOR CON720RHD Manuale di istruzioni

Clarke

Clarke CONTRACTOR CON1200RD Manuale di istruzioni

Clarke

Clarke CHD820 Manuale di istruzioni

Clarke

Clarke CDS1 Manuale utente

Clarke

Clarke Air CAT107 Manuale di istruzioni

Clarke

Clarke CAT27B Manuale di installazione e funzionamento

Clarke

Clarke Metalworker CMD10 Manuale

Clarke

Clarke Metalworker CMD1225C Manuale di installazione e funzionamento

Clarke

Clarke Contactor CON1200 Manuale di installazione e funzionamento

Clarke

Clarke CMD300 Manuale di istruzioni

Clarke

Clarke CAT60 Manuale di installazione e funzionamento

Clarke

Clarke 6479500 Manuale di installazione e funzionamento

Clarke

Clarke CONTRACTOR CHD1050 Manuale utente

Clarke

Clarke CAT100 Manuale di installazione e funzionamento

Clarke

Clarke CHD850 Manuale di istruzioni

Clarke

Clarke Air CAT214 Manuale di installazione e funzionamento

Clarke

Clarke CAT116 Manuale di istruzioni

Clarke

Clarke Air CAT68 Manuale di istruzioni

Clarke

Clarke CHD900 Manuale di istruzioni

Manuali Trapano popolari di altre marche

Makita

Makita BDF456 Manuale utente

Black & Decker

Black & Decker LDX220 Manuale utente

Hitachi

Hitachi DH 40MA Manuale utente

Challenge

Challenge JO Manuale tecnico di riferimento

Makita

Makita LXFD01 Manuale utente

Festool

Festool T18+3 Manuale utente

Milwaukee

Milwaukee M12 FPDX-202X Manuale utente

EINHELL

EINHELL TE-RH 32 E Manuale utente

Makita

Makita DHP484 Manuale utente

Makita

Makita FD05 Manuale utente

Bosch

Bosch PSB 530 RA Manuale utente

Maximum

Maximum 054-1359-4 Manuale utente

Makita

Makita HP332D Manuale utente

Raider

Raider RDP-HD31H Manuale utente

Bort

Bort BPM-1400x2 Manuale utente

Black & Decker

Black & Decker 7266 Manuale utente

KENT USA

KENT USA TRD1230 Manuale utente

Bosch

Bosch GSB 19-2 RE Manuale utente