Clarke CRD1250 Manuale di istruzioni

OPERATION & MAINTENANCE

INSTRUCTIONS

GC0913

ROTARY HAMMER DRILL

MODEL NO: CRD1250

PART NO: 6482015

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

INTRODUCTION

Thank you for purchasing this CLARKE Hammer Drill. The CRD1250 is designed

for general drilling/masonry drilling/chiselling/drill & hammer use in light

industrial applications.

Before attempting to use this product, please read this manual thoroughly and

follow the instructions carefully. In doing so you will ensure the safety of yourself

and that of others around you, and you can look forward to your purchase

giving you long and satisfactory service.

GUARANTEE

This product is guaranteed against faulty manufacture for a period of 12

months from the date of purchase. Please keep your receipt which will be

required as proof of purchase.

This guarantee is invalid if the product is found to have been abused or

tampered with in any way, or not used for the purpose for which it was

intended.

Faulty goods should be returned to their place of purchase, no product can

be returned to us without prior permission.

This guarantee does not effect your statutory rights.

SAFETY PRECAUTIONS

WORK AREA

1. Keep work area clean and well lit. Cluttered and dark areas invite

accidents.

2. Do not operate power tools in explosive atmospheres, such as in the

presence of flammable liquids, gases or dust. Power tools create sparks

which may ignite the dust or fumes.

3. Keep children and bystanders away while operating a power tool.

Distractions can cause you to lose control.

WARNING: READ ALL INSTRUCTIONS. FAILURE TO FOLLOW ALL

INSTRUCTIONS LISTED BELOW MAY RESULT IN ELECTRIC SHOCK, FIRE AND/

OR SERIOUS INJURY. THE TERM “POWER TOOL” IN ALL WARNINGS LISTED

BELOW REFERS TO YOUR HAMMER DRILL.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

ELECTRICAL SAFETY

1. Avoid body contact with earthed or grounded surfaces such as pipes,

radiators, ranges or refrigerators. There is an increased risk of electric shock

if your body is earthed or grounded.

2. Do not expose power tools to rain or wet conditions. Water entering a

power tool will increase the risk of electric shock.

3. When operating a power tool outdoors, use an extension cord suitable for

outdoor use. Use of a cord suitable for outdoor use reduces the risk of

electric shock.

PERSONAL SAFETY

1. Stay alert, watch what you are doing and use common sense when

operating a power tool. Do not use a power tool while you are tired or

under the influence of drugs, alcohol or medication. A moment of

inattention while operating power tools may result in personal injury.

2. Use safety equipment. Always wear eye protection. Safety equipment such

as dust mask, non-skid safety shoes, or hearing protection used for

appropriate conditions will reduce personal injuries.

3. Avoid accidental starting. Ensure the switch is in the off position before

connecting to the power supply.

4. Do not overreach. Keep proper footing and balance at all times. This

enables better control of the power tool in unexpected situations.

5. Dress properly. Do not wear loose clothing or jewellery. Keep your hair,

clothing and gloves away from moving parts. Loose clothes, jewellery or

long hair can be caught in moving parts.

POWER TOOL USE AND CARE

1. Do not force the power tool. Use the correct power tool for your

application. The correct power tool will do the job better and safer at the

rate which it was designed.

2. Do not use the power tool if the switch does not turn it on and off. Any

power tool that cannot be controlled with the switch is dangerous and

must be repaired.

3. Disconnect the battery before making any adjustments, changing

accessories, or storing power tools. Such preventive safety measures

reduce the risk of starting the power tool accidentally.

4. Store idle tools out of the reach of children and do not allow persons

unfamiliar with the power tool or these instructions to operate the power

tool. Power tools are dangerous in the hands of untrained users.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

5. Maintain power tools. Check for misalignment or binding of moving parts,

breakage of parts and any other condition that may affect the power tools

operation. If damaged, have the power tool repaired before use. Many

accidents are caused by poorly maintained power tools.

6. Keep cutting tools sharp and clean. Poorly maintained cutting tools with

sharp cutting edges are less likely to bind and are easier to control.

7. Use the power tool and accessories in accordance with these instructions

and in the manner intended for the particular type of power tool, taking

into account the working conditions and the work to be performed. Use of

the power tool for operations different from intended could result in a

hazardous situation.

SERVICE

1. Have your power tool serviced by a qualified repair person using only

identical replacement parts. This will ensure that the safety of the power

tool is maintained.

SAFETY SYMBOLS

ENVIRONMENTAL PROTECTION

Recycle unwanted materials instead of disposing of them as waste.

All tools, accessories and packaging should be sorted, taken to a

recycling centre and disposed of in a manner which is compatible

with the environment.

Read instruction

manual before use

Wear dust mask

Class 2 Double

Insulated

Wear ear defenders

CE Mark Wear safety glasses

Weee Directive

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

ELECTRICAL CONNECTIONS

This product battery charger is provided with a standard 13 amp, 230 volt

(50Hz), BS 1363 plug, for connection to a standard, domestic electrical supply.

Should the plug need changing at any time, ensure that a plug of identical

specification is used.

If the colours of the wires in the power cable of this product do not correspond

with the markings on the terminals of your plug, proceed as follows.

• The wire which is coloured Blue must be connected to the terminal

which is marked Nor coloured Black.

• The wire which is coloured Brown must be connected to the terminal

which is marked Lor coloured Red.

We strongly recommend that this machine is connected to the mains supply

via a Residual Current Device (RCD)

If in any doubt, consult a qualified electrician. DO NOT attempt any repairs

yourself.

This symbol indicates that this is a Class II product, and does not require

an earth connection.

WARNING! Read these electrical safety instructions thoroughly

before connecting the product to the mains supply.

WARNING! The wires in the power cable of this product are

coloured in accordance with the following code:

Blue = Neutral Brown = Live

Plug must be BS1363/A approved.

Always fit a 5 Amp fuse.

Ensure that the outer sheath of the cable is firmly held by the clamp

Neutral

(Blue)

Live

(Brown)

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

OVERVIEW

NO DESCRIPTION NO DESCRIPTION

1 Dust Guard 7 Hammer Control

2 Fastening Sleeve 8 Drill Control

3 Switch Trigger 9 Lock Pin

4 Handle Attachment 10 Off-Lock Knob

5 Rear Cover 11 Greasing Point Cover

6DepthStop

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

CARTON CONTENTS

The following items should be supplied in the carton. If any parts are missing or

damaged, please see your Clarke dealer.

SETUP AND OPERATION

BEFORE STARTING WORK

1. Before drilling into walls and floors etc., check first that there are no hidden

electrical cables, gas or water pipes etc.

1 Moulding plastic carrying case 9 Black moulded bit case

2 Rotary Hammer Drill 10 8mm SDS plus masonry drill bit

3 Auxiliary Handle 11 10mm SDS plus masonry drill bit

4 Drill Chuck (1.3-13mm) 12 12mm SDS plus masonry drill bit

5 Chuck Key 13 SDS plus masonry chisel bits

6 Dust Cap 14 Depth Rod

7 Spare Set of Brushes 15 Wrench

8 Pot of Grease

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

2. Check the mains voltage before plugging in and switching on.

FITTING AND CHANGING TOOLS

1. Clean tools, and apply a thin film of grease before fitting.

2. Pull back the fastening sleeve and hold, push and rotate the dust free tool

Into the tool holder as far as it will go, release the fastening sleeve, the tool

will then be locked in automatically.

3. Check the tool is locked in securely by attempting to pull the tool out.

REMOVING TOOLS

1. Ensure the drill has completely stopped and is disconnected from the

electrical supply.

2. Pull back the fastening sleeve and hold:- pull the tool out of the tool holder

and store safely.

NOTE: for your protection, if the tool is hot, either allow it to cool down first or

use industrial gloves to remove the tool.

STARTING WORK

1. Ensure the work area is as hazard

free as possible.

2. Select and install the tool to be

used, (see paragraph 2).

3. If required, set the depth stop and

adjust the support handle

attachment for the most

comfortable position as shown. To

install the depth stop, loosen the

support handle by turning it

anticlockwise. Insert the depth

stop rod through the hole in the

support handle and set to the

required depth, adjusting the

position of the handle attach-

ment if required, and secure in place by re-tightening the support handle.

• For safety, always use the hammer drill with the handle attached.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

4. Set the required mode, (see Drill

Mode Selection below).

• When drilling vertically

overhead, fit the rubber dust

collector shown onto the drill.

5. Position the tool against the

surface to be drilled, depress the

OFF lock knob (10) and then

squeeze the trigger switch (3).

NOTE: If using the hammer action do

not start the drill until the tool is in contact with the work surface.

DRILL MODE SELECTION

HAMMER STOP

Your drill is equipped with a hammer stop facility for smoother drilling.

To select this mode turn the hammer control switch (7) to the position

marked:

Depress the lock pin (9) then turn the drill control (8) so that the

position marked:

coincides with the arrow on the machines case.

DRILL STOP

For chiselling it is necessary to deactivate the drilling action as follows:

1. Turn the hammer control switch (7) to the position marked:

2. Depress the lock pin (9) then turn the drill control (8) so that the

position marked coincides with the arrow on the machine case.

HAMMER AND DRILL

To activate the hammer and drill mode turn the hammer control

switch (7) to the position marked:

Depress the lock pin (9) and turn the drill control (8) so that the position

marked thus, coincides with the arrow on the machine’s case.

IMPORTANT: When hammer drilling you only need to apply light

pressure. Too much pressure will place unnecessary load on the motor.

Check the drill bits regularly, re-sharpen or replace.

DRILLING TIPS

1. Always use sharp, good quality drill bits. The performance of your drill is

dependant on the quality of the bits used.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

2. After drilling material to the full depth, do not simply pull out the drill but

maintain chuck rotation to ease withdrawal.

3. Reduce the pressure on the drill bit when it is about to break through. This

will prevent the drill from jamming.

4. If drilling a large hole, first drill a pilot hole using a smaller drill bit.

5. Always apply pressure to your drill bit in a straight line and, where possible,

at right angles to the workpiece.

6. When drilling holes or driving screws into walls, floors etc., always make sure

that there are no live electrical wires in the path of the bit.

7. When drilling in metal, the materials being drilled can become hot. To

reduce overheating use a suitable cooling lubricant. No cooling lubricant is

necessary when drilling cast iron or brass as they should be drilled dry.

8. When drilling metal, the harder the metal the slower the drill speed.

Similarly, the bigger the drill bit the slower the speed.

9. Always start drilling at a slow speed to prevent the drill from slipping out of

the pop mark or indent, gradually increasing speed until the optimum

cutting speed is achieved whilst maintaining a MODERATE pressure ONLY.

NEVER force the drill bit into the work. This will overheat the tip and cause it

to dull very quickly.

10. To prevent the drill bit from slipping when starting to drill a hole in metal, use

a centre punch to make an indentation at the start point.

11. When drilling in wood, clamp a piece of scrap wood to the underside of

the material to avoid splintering.

12. Always drill directly in line with the bit. Do not use sideways movement as

this may damage the drill or cause the bit to break.

13. Large holes should be drilled with wood augers, flat wood bits or hole saws.

MAINTENANCE AND SERVICING

1. After use, remove the drill or screwdriver bit, open the chuck jaws and tap

the side of the chuck to remove any dust, or chippings etc.

2. Keep the cooling vents clear.

3. Keep the handle clean and free from oil and grease.

4. Worn or damaged parts must be replaced by qualified personnel.

5. Clean the tool regularly, use a soft brush and or soft cleaning cloth. DO

NOT use any chemicals or harsh abrasives to clean the tool.

Altri manuali per CRD1250

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Clarke Trapano

Clarke

Clarke Contactor CON1200 Manuale di installazione e funzionamento

Clarke

Clarke CDD20Li Manuale di istruzioni

Clarke

Clarke X-pro CAT158 Manuale di installazione e funzionamento

Clarke

Clarke air CAT137 Manuale di installazione e funzionamento

Clarke

Clarke CAT100 Manuale di installazione e funzionamento

Clarke

Clarke CAT60 Manuale di installazione e funzionamento

Clarke

Clarke CBM1-B Manuale di installazione e funzionamento

Clarke

Clarke Air CAT214 Manuale di installazione e funzionamento

Clarke

Clarke 3110835 Manuale di installazione e funzionamento

Clarke

Clarke CHD900 Manuale di istruzioni

Clarke

Clarke CRD1250 Manuale utente

Clarke

Clarke CAT87 Manuale di installazione e funzionamento

Clarke

Clarke CHT599 Manuale utente

Clarke

Clarke CAT123 Manuale di istruzioni

Clarke

Clarke Metalworker CMD10 Manuale

Clarke

Clarke 6479500 Manuale di installazione e funzionamento

Clarke

Clarke Contractor CON1500RDV Manuale di istruzioni

Clarke

Clarke CAT137 Manuale di installazione e funzionamento

Clarke

Clarke CAT116 Manuale di istruzioni

Clarke

Clarke CMD300 Manuale

Clarke

Clarke CONTRACTOR CON400RHD Manuale di istruzioni

Clarke

Clarke X-Pro CAT207 Manuale di installazione e funzionamento

Clarke

Clarke Metalworker CMD1225C Manuale di installazione e funzionamento

Clarke

Clarke CHD820 Manuale di istruzioni

Manuali Trapano popolari di altre marche

Makita

Makita BDF456 Manuale utente

Black & Decker

Black & Decker LDX220 Manuale utente

Hitachi

Hitachi DH 40MA Manuale utente

Challenge

Challenge JO Manuale tecnico di riferimento

Makita

Makita LXFD01 Manuale utente

Festool

Festool T18+3 Manuale utente

Milwaukee

Milwaukee M12 FPDX-202X Manuale utente

EINHELL

EINHELL TE-RH 32 E Manuale utente

Makita

Makita DHP484 Manuale utente

Makita

Makita FD05 Manuale utente

Bosch

Bosch PSB 530 RA Manuale utente

Maximum

Maximum 054-1359-4 Manuale utente

Makita

Makita HP332D Manuale utente

Raider

Raider RDP-HD31H Manuale utente

Bort

Bort BPM-1400x2 Manuale utente

Black & Decker

Black & Decker 7266 Manuale utente

KENT USA

KENT USA TRD1230 Manuale utente

Bosch

Bosch GSB 19-2 RE Manuale utente