Clarke IRD20 Manuale di istruzioni

OPERATION & MAINTENANCE

INSTRUCTIONS

GC0315

INFRARED DIESEL HEATER

MODEL NO: IRD20

PART NO: 6920420

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

INTRODUCTION

Thank you for purchasing this CLARKE Infrared Heater.

Before attempting to use this product, please read this manual thoroughly and

follow the instructions carefully. In doing so you will ensure the safety of yourself

and that of others around you, and you can look forward to your purchase

giving you long and satisfactory service.

GUARANTEE

This product is guaranteed against faulty manufacture for a period of 12

months from the date of purchase. Please keep your receipt which will be

required as proof of purchase.

This guarantee is invalid if the product is found to have been abused or

tampered with in any way, or not used for the purpose for which it was

intended.

Faulty goods should be returned to their place of purchase, no product can

be returned to us without prior permission.

This guarantee does not effect your statutory rights.

ENVIRONMENTAL RECYCLING POLICY

Through purchase of this product, the customer is taking on the

obligation to deal with the WEEE in accordance with the WEEE

regulations in relation to the treatment, recycling & recovery and

environmentally sound disposal of the WEEE.

In effect, this means that this product must not be disposed of with general

household waste. It must be disposed of according to the laws governing

Waste Electrical and Electronic Equipment (WEEE) at a recognised disposal

facility.

If disposing of this product or any damaged components, do not dispose of

with general waste. This product contains valuable raw materials. Metal

products should be taken to your local civic amenity site for recycling of metal

products.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

GENERAL SAFETY PRECAUTIONS

GENERAL

1. Always read and ensure you fully understand the following precautions and

the hazards associated with this type of heater. Do not allow anyone who

has not read these instructions to operate this heater.

2. Always check for damage before using the heater. Any damage should be

properly repaired or the part replaced. If in doubt, do not use the heater

and consult your local Clarke dealer.

3. Never carry out any modifications to this product. If experiencing difficulty

of any kind consult your local dealer.

4. Use the heater in accordance with any applicable fire regulations.

OPERATING ENVIRONMENT

1. Do not expose the heater or power cable to rain or wet conditions. Any

water entering the heater will increase the risk of electric shock.

2. Never use the heater where petrol, paint thinners or other highly flammable

vapour or where high levels of airborne dust may be present.

3. Never locate the heater facing combustible materials such as screens,

workshop furniture etc.

4. Do not locate the heater close to an adjacent wall or ceiling. Avoid

placing the heater directly below power socket outlets.

5. Always locate the heater on a level, flat, fireproof floor. Ensure that the

heater is correctly and safely positioned as described on pages 10-11.

6. Disconnect the heater from the power supply when not in use.

7. Never place anything on top of the heater.

8. Always keep combustibles, like paper and wood at least 2.5 m from the

front of the heater and 2.5 m) from the top, sides and rear.

9. Locate the heater 2.5 m from canvas or plastic coverings and secure them

to prevent movement.

10. Operate only on a stable, level surface.

CAUTION: FAILURE TO FOLLOW THESE PRECAUTIONS COULD RESULT IN

PERSONAL INJURY, AND/OR DAMAGE TO PROPERTY.

CAUTION: DUE TO THE HIGH SURFACE AND EXHAUST TEMPERATURES,

ADULTS AND CHILDREN MUST KEEP CLEAR OF THE UNIT TO AVOID BURNS

OR CLOTHING IGNITION.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

11. Use only in accordance with local regulations and relevant building codes.

VENTILATION

Even though this heater operates very close to 100 percent combustion

efficiency, it still produces small amounts of carbon monoxide.

Carbon monoxide (CO) is toxic.

CO can build up in a confined spaces and failure to provide adequate

ventilation can be fatal.

The early symptoms of asphyxiation caused by inadequate ventilation are:

WE RECOMMEND THE USE OF A CARBON MONOXIDE DETECTOR

1. Only use in well ventilated areas. NEVER use the heater in living or sleeping

areas.

2. Always ensure that ample ventilation is present if the heater is being lit

following a long period without use.

3. Never attach any duct work to the front of the heater.

4. Never cover or impede air flow into or out of the heater.

PERSONAL SAFETY

1. When the heater is to be operated in the presence of other people the

user is responsible for informing those present of the safety precautions and

of the hazards involved.

2. The heater is not to be used by children or persons with reduced physical,

sensory or mental capabilities, or lack of experience and knowledge.

3. Always ensure that people and animals are at least 2.5 m away from the

front of the heater when in operation.

4. Never leave a heater unsupervised while operating - someone should

always be made responsible for monitoring it.

5. Never use in living spaces and/or where children may be present.

6. Never move, replenish the fuel supply or handle the heater when it is hot, or

operating. Turn it off and wait for it to cool down first.

7. Do not move or service the heater while hot or in operation.

8. This heater will be hot when in operation and should not be touched until it

has fully cooled down after shutting off.

• headache • nausea

• dizziness • dry mouth or sore throat

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

9. Never leave a heater plugged in without adult supervision if children or

animals are likely to be present.

REFUELLING

1. Always refuel in a well ventilated area.

2. Always refuel away from any source of heat.

3. Never overfill the tank, only fill to the level specified.

4. Use only clean diesel or kerosene. NEVER use gasoline, paint thinners,

alcohol or other highly flammable fuels.

5. Take care not to spill diesel or kerosene onto the power cable as this could

damage the insulation.

ELECTRICAL SAFETY

1. Electrical appliances must match the power outlet. Never modify the plug

in any way. Do not use adaptor plugs with earthed (grounded) appliances.

Correct plugs and outlets will reduce the risk of electric shock.

2. Do not abuse the electrical cable. Never use the cable for pulling or

unplugging the heater. Keep the cable away from sources of heat, oil,

sharp edges or moving parts. Damaged or tangled cables increase the risk

of electric shock.

3. Keep the mains cable well away from machines and ensure an adequate

electrical supply is close at hand so that the operation is not restricted by

the length of the cable.

4. Always disconnect from the mains supply before moving the heater or

performing any maintenance tasks.

5. Inspect the mains cable regularly for signs of damage. DO NOT use if it is

damaged and always keep it away from the source of heat.

6. If the power cable is damaged, it must be replaced by the manufacturer,

its service agent, or similarly qualified persons in order to avoid a hazard.

SERVICE & REPAIRS

1. Check the heater for damage before use. DO NOT use if the heater is

damaged. Any damage should be properly repaired or the part replaced.

If in doubt, DO NOT use the heater. Consult your local dealer.

2. When necessary, have your heater serviced or repaired by a qualified

person using identical replacement parts. This will ensure that the safety of

the heater is maintained.

3. Please keep these instructions in a safe place for future reference.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

ELECTRICAL CONNECTIONS

Before switching the product on, make sure that the voltage of your electricity supply is

the same as that indicated on the rating plate. This product is designed to operate on

230VAC 50Hz. Connecting it to any other power source may cause damage.

This product may be fitted with a non-rewireable plug. If it is necessary to change the

fuse in the plug, the fuse cover must be refitted. If the fuse cover becomes lost or

damaged, the plug must not be used until a suitable replacement is obtained.

If the plug has to be changed because it is not suitable for your socket, or due to

damage, it should be cut off and a replacement fitted, following the wiring instructions

shown below. The old plug must be disposed of safely, as insertion into a mains socket

could cause an electrical hazard.

If the colours of the wires in the power cable of this product do not correspond with the

markings on the terminals of your plug, proceed as follows.

• The wire which is coloured Blue must be connected to the terminal which is

marked Nor coloured Black.

• The wire which is coloured Brown must be connected to the terminal which

is marked Lor coloured Red.

• The wire which is coloured Yellow and Green must be connected to the

terminal which is marked E or or coloured Green.

We strongly recommend that this machine is connected to the mains supply

via a Residual Current Device (RCD)

If in any doubt, consult a qualified electrician. DO NOT attempt any repairs yourself.

WARNING! Read these electrical safety instructions thoroughly

before connecting the product to the mains supply.

WARNING! The wires in the power cable of this product are

coloured in accordance with the following code:

Blue = Neutral Brown = Live Yellow and Green = Earth

Plug must be BS1363/A approved.

Always fit a 13 Amp fuse.

Ensure that the outer sheath of the cable is firmly held by the clamp

Neutral

(Blue)

Live

(Brown)

Earth

(Green and Yellow)

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

TECHNICAL SPECIFICATION

SAFETY SYMBOLS

The following symbols appear on the unit.

Dimensions (L x W x H) 600 x 310 x 570 mm

Weight (empty) 15.5 kg

Fuel Diesel/paraffin/kerosene

Fuel Consumption 1.5 L per hour

Fuel Tank Capacity 11 litres

Ignition type Direct spark

Max running time 8 hrs

Air displacement 400 M3/hr

Continuous working time 8 hr

Thermostatic settings 5 -45oC

Over heating protection 160oC

Max capacity 15 KW

14000 Kcal/h

51180 Btu/h

Duty Cycle S1 (continuous)

Fuel Pump Pressure 8 bar

Electrical Supply 230 V 50 Hz 1 ph

Protection Degree IPX0

Sound Pressure Level 60 dB LpA

Sound Power Level Measured 60 dB LWA

Hot Surface, do not

touch

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

IRD20 HEATER OVERVIEW

The IRD20 Infrared Diesel Heater is ideal for the following applications:

• Heating work areas in large, well ventilated rooms or outbuildings.

• Dust-free drying of components.

• Drying out and de-icing of construction areas, concrete, walls etc.

NO DESCRIPTION NO DESCRIPTION

1 Fuel Gauge 5 Power-On LED

2 Fuel Tank 6 Power Switch

3 Fuel Filler Cap 7 Temperature Control Knob

4 Digital Temperature Display 8 Power Cable

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

• Defrosting large machines and buildings.

• Heating of buildings under alteration or repair.

FUNCTIONAL DESCRIPTION

FUEL SYSTEM

Fuel is transferred from the tank by an electromagnetic pump, into the nozzle

and atomised. A high voltage ignition transformer sends current to the tips of

the ignition needles which provide the spark to fire the atomised fuel.

AIR SYSTEM

The fan on the back of the unit helps provide the oxygen for combustion as

well as blowing the heated air from the unit. The fans in the centre of the unit

cool the surface temperature of the heater.

SAFETY SYSTEMS

The unit is fitted with a temperature limit sensor, which is designed to turn the

heater off if the temperature should rise to an unsafe level. If the sensor is

tripped and the heater is turned off it may require a service. Once the

temperature falls back below the reset temperature, the heater should re-

start.

The heater is fitted with an electrical circuit breaker to protect the internal

components from damage. If the heater should fail to work, this fuse may

require checking.

The heater uses a photocell to detect the flame in the combustion chamber.

Should the flame extinguish, the sensor will cut off the electrical current and

the heater will shut off.

The heater is fitted with a tilt switch designed to turn the unit off immediately if

it should tip over beyond a pre-determined angle.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

PREPARATION

UNPACKING

1. Remove heater from carton. and remove all protective material which

may have been used for shipment.

2. Check the heater for any damage that may have occurred in transit and

notify your Clarke dealer immediately should any be apparent.

3. Fit the carrying handle to the top

of the heater using the screws

supplied.

4. Fit the heatshield to the heater

body using the screws supplied.

SUITABLE FUELS

Diesel, paraffin or kerosene are the only fuels that should be used in this heater.

FILLING THE FUEL TANK

IMPORTANT: In cold weather, condensation may develop in the tank if the

tank is empty. Before filling the fuel tank for the first time or after extended

storage periods, vent the fuel tank of any moisture or condensation.

1. Follow all of the “Safety Precautions”.

Indice

Altri manuali Clarke Stufa

Clarke

Clarke Devil 6003 Manuale

Clarke

Clarke 6933980 Manuale di istruzioni

Clarke

Clarke DEVIL 371SPC Manuale di installazione e funzionamento

Clarke

Clarke CONTRACTOR DEVIL 351C Manuale di installazione e funzionamento

Clarke

Clarke DEVIL 370SPD Manuale di installazione e funzionamento

Clarke

Clarke IRD40 6920415 Manuale di installazione e funzionamento

Clarke

Clarke DEVIL 340 Manuale di istruzioni

Clarke

Clarke XR60 Manuale di installazione e funzionamento

Clarke

Clarke DEVIL 370PC Manuale di installazione e funzionamento

Clarke

Clarke Devil 355MD Istruzioni operative

Clarke

Clarke OFR13/250 Manuale di istruzioni

Clarke

Clarke OFR 9 Manuale di istruzioni

Clarke

Clarke DEVIL 7005 Manuale di istruzioni

Clarke

Clarke DEVIL 371PC Manuale di installazione e funzionamento

Clarke

Clarke DEVIL 4003 Manuale di istruzioni

Clarke

Clarke Devil 370B Series Manuale di installazione e funzionamento

Clarke

Clarke DEVIL 9000PTC Manuale di istruzioni

Clarke

Clarke DEVIL 7030 Manuale di istruzioni

Clarke

Clarke Devil 6002 Manuale

Clarke

Clarke CONTRACTOR GRH30 Manuale di istruzioni

Clarke

Clarke OFR 9 Manuale di istruzioni

Clarke

Clarke DEVIL155 Manuale

Clarke

Clarke BR13/250 Manuale di istruzioni

Clarke

Clarke IQ2000S Manuale elenco delle parti

Manuali Stufa popolari di altre marche

oventrop

oventrop Regucor Series Manuale utente

Blaze King

Blaze King CLARITY CL2118.IPI.1 Manuale utente

ELMEKO

ELMEKO ML 150 Manuale utente

BN Thermic

BN Thermic 830T Manuale utente

KING

KING K Series Guida

Empire Comfort Systems

Empire Comfort Systems RH-50-5 Guida rapida

Well Straler

Well Straler RC-16B Manuale utente

EUROM

EUROM 333299 Manuale utente

Heylo

Heylo K 170 Manuale utente

Eterna

Eterna TR70W Manuale utente

IRSAP

IRSAP The Radiator Company Ovali Manuale utente

Empire Heating Systems

Empire Heating Systems WCC65 Manuale utente

Wetekom

Wetekom 92 86 43 Manuale utente

Desa

Desa SPC170-F Manuale utente

Watlow

Watlow Watrod Electric Tubular Heaters Manuale utente

Haverland

Haverland ECO-DRY GPS Series Manuale elenco delle parti

Stelpro

Stelpro ASILVC2060 Series Manuale utente

iLO

iLO IHP2424 Manuale operativo