Clarke CAT210 Manuale di installazione e funzionamento

OPERATING & MAINTENANCE

INSTRUCTIONS

ORIGINAL INSTRUCTIONS GC1019 - ISS 1

AIR BLOW GUN WITH HOSE

MODEL NO: CAT210

PART NO: 3120527

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

INTRODUCTION

Thank you for purchasing this CLARKE Blow Gun.

Before attempting to use this product, please read this manual thoroughly and

follow the instructions carefully. In doing so you will ensure the safety of yourself

and that of others around you, and you can look forward to your purchase

giving you long and satisfactory service.

Please keep these instructions in a safe place for future reference.

SPECIFICATION

GUARANTEE

This product is guaranteed against faulty manufacture for a period of 12

months from the date of purchase. Please keep your receipt which will be

required as proof of purchase.

This guarantee is invalid if the product is found to have been abused or

tampered with in any way, or not used for the purpose for which it was

intended.

Faulty goods should be returned to their place of purchase, no product can

be returned to us without prior permission.

This guarantee does not affect your statutory rights.

Dimensions - Blow Gun (L x W x H) 248 x 17 x 120 mm

Dimensions - Hose PU 6.5 X10mm WP 120PSI x 2.5m

Weight 297 g

Max Operating Pressure 90 psi (6.2 bar)

Air Inlet Size 1/4“BSP Female

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

COMPRESSED AIR REQUIREMENTS

Use only clean, dry, regulated compressed air as a power source.

Air compressors used with the tool must comply with the appropriate

European Community Safety Directives.

A build-up of moisture or oil in the air compressor will accelerate wear and

corrosion in the tool. Ensure any moisture is drained from the compressor daily

and the inlet filter is kept clean.

If an unusually long air hose is required, (over 8 metres), the line pressure or the

hose inside diameter may need to be increased.

The air hose must be rated at least 150% of the maximum operating pressure of

the air tool.

A typical air line layout is shown above. If an automatic in-line filter/regulator is

used, it will keep the air tool in good condition, but should be regularly

checked.

For optimum performance it is recommended that a 3/8” ID hose is used.

DO NOT exceed the maximum operating pressure. It is recommended that air

pressure does not exceed 90 psi (6.2 bar). Higher pressures and dirty air will

shorten the life of the blow gun due to faster wear and is a possible safety

hazard.

WARNING: COMPRESSED AIR CAN BE DANGEROUS. ENSURE THAT YOU

ARE FAMILIAR WITH ALL PRECAUTIONS RELATING TO THE USE OF

COMPRESSORS AND COMPRESSED AIR.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

GENERAL SAFETY RULES

WORK ENVIRONMENT

1. ALWAYS keep the work area clean and tidy.

2. ALWAYS dress appropriately - Do not wear loose clothing or jewellery. Tie

long hair out of the way.

3. ALWAYS keep children and visitors away - Do not let children handle the

blow gun.

4. DO NOT operate the blow gun where there are flammable liquids or gases.

USE OF AIR POWERED TOOLS

1. ALWAYS stay alert and use common sense - do not operate this blow gun

when you are tired or under the influence of alcohol, drugs or medication.

2. ALWAYS wear eye protectors when using the blow gun. Eye protectors must

provide protection from flying particles from the front and the side.

3. DO NOT use the blow gun when other persons or animals are nearby or

may be hit by flying debris caused by the blow gun.

4. DO NOT overreach - Keep proper footing and balance at all times.

5. DO NOT use oxygen, CO2, combustible gasses or any type of bottled gas

as a source of power for this blow gun.

6. DO NOT connect the air hose with your finger on the trigger.

7. DO NOT exceed the maximum pressure of 90 psi / 6.2 bar.

8. ALWAYS keep the air hose away from heat, oil and sharp edges.

9. DO NOT fit the blow gun to any stand or clamping device that may

damage it.

10. ALWAYS check air hoses for leaks or worn condition before use and ensure

that all connections are secure.

11. DO NOT use the blow gun for any purpose than that described in this

manual.

12. DO NOT discharge this blow gun at any persons or animals.

13. DO NOT insert into any part of yours or anyone else’s body.

CAUTION: FAILURE TO FOLLOW THESE PRECAUTIONS COULD RESULT IN

PERSONAL INJURY AND/OR DAMAGE TO PROPERTY.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

14. DO NOT point directly at a person’s skin or at a fire.

15. DO NOT carry out any alterations or modifications to the blow gun.

16. ALWAYS disconnect from the air supply when performing maintenance.

17. DO NOT use the blow gun if it is defective or operating abnormally.

18. ALWAYS maintain the blow gun with care. Keep it clean for the best and

safest performance.

TRANSPORT & STORAGE

1. DO NOT carry the blow gun by the air hose or with your finger on the

trigger.

2. When not in use the blow gun must be disconnected from the air supply

and stored in a dry place out of the reach of children.

3. Avoid storing a blow gun where the temperature is below 0oC.

BEFORE USE

CONNECTING THE AIRLINE

Ensure the air supply is isolated from

the airline at a shut-off valve.

1. Connect a suitable hose to the air

inlet connector as shown.

2. Connect the other end of the air

hose to the air compressor.

3. Set the compressed air pressure to

suit the task at the airline regulator.

4. Turn on the air supply and check

for air leaks. Rectify any found before proceeding.

• PTFE tape may be useful for sealing threaded connections.

5. Your blow gun is now ready for use.

DISCONNECTING THE AIR SUPPLY

1. Do not disconnect the airline until the supply is isolated at a shut-off valve.

2. Once the pressure has been isolated, disconnect the air supply hose from

the blow gun.

3. Shut down the compressor at the end of the work session.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

MAINTENANCE

1. Before use, drain any condensate from the airline filter and compressor.

2. Clean thoroughly after use with a suitable solvent.

PERFORMANCE

Please note that factors other than the air tool may affect its operation and

efficiency such as reduced compressor output, excessive drain on the airline,

moisture or restrictions in the air-line, or the use of connectors of improper size

or poor condition which will reduce air supply.

Your CLARKE air tool has been designed to give long and trouble free service.

If, however, having followed the instructions in this booklet carefully, you

encounter problems, take the unit to your local CLARKE dealer.

ACCESSORIES

A wide range of accessories is available including filter/regulators, lubricators,

high-pressure hoses (5 to 50 metres) etc.

Contact your CLARKE dealer for further information or the CLARKE

International Service Department.

WARNING: MAKE SURE THAT THE BLOW GUN IS DISCONNECTED FROM THE

AIR SUPPLY BEFORE ANY CLEANING OR MAINTENANCE.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

COMPONENT PARTS

No Description No Description

1 Main Housing 8 O-ring

2 Spring 9 Trigger

3 O-ring 10 Pin

4 Valve stem 11 Air inlet

5 O-ring 12 O-ring

6 O-ring 13 Air nozzle seat

7 Valve stem 14 Air nozzle

Indice

Altri manuali Clarke Utensili elettrici

Clarke

Clarke CHT 459 Manuale utente

Clarke

Clarke Strong-Arm CSA15F Manuale di installazione e funzionamento

Clarke

Clarke STRONG-ARM CSA4B Manuale di istruzioni

Clarke

Clarke CONTRACTOR CON1450WC Guida alla risoluzione dei problemi

Clarke

Clarke CAT141 Manuale di installazione e funzionamento

Clarke

Clarke CHT674 Manuale utente

Clarke

Clarke CDP10B Manuale di istruzioni

Clarke

Clarke Strong-Arm CSA50FPB Manuale di istruzioni

Clarke

Clarke CPSB100B Manuale di istruzioni

Clarke

Clarke Air CSG3KC Manuale di installazione e funzionamento

Clarke

Clarke CBM 2B Manuale di installazione e funzionamento

Clarke

Clarke Contractor CON750 Manuale di istruzioni

Clarke

Clarke Air CAT105 Manuale di istruzioni

Clarke

Clarke Woodworker CPT600 Manuale di installazione e funzionamento

Clarke

Clarke X-Pro CAT202 Manuale di installazione e funzionamento

Clarke

Clarke CIR450C Manuale di installazione e funzionamento

Clarke

Clarke CEW1000 Manuale

Clarke

Clarke CTILG 5060287 Istruzioni per l'installazione

Clarke

Clarke PRO236 Manuale di installazione e funzionamento

Clarke

Clarke Contractor CON15 Manuale di installazione e funzionamento

Clarke

Clarke CCRT266 Manuale di istruzioni

Clarke

Clarke CE7 PRO Manuale utente

Clarke

Clarke cp185 Manuale di installazione e funzionamento

Clarke

Clarke DHC-2 Manuale di istruzioni

Manuali Utensili elettrici popolari di altre marche

AEG

AEG OMNI-JS Manuale utente

SIP

SIP 01533 Manuale utente

Ribimex

Ribimex PRS499 Manuale utente

3M Fiber Optic Connector Crimp Tool Manuale utente

Ryobi

Ryobi P524 Manuale utente

ROJEK

ROJEK FSN 300A Manuale utente

Kemper

Kemper 1740PRO Manuale utente

WABCO

WABCO OptiTire Manuale utente

EINHELL

EINHELL TE-MS 18/210 Li Manuale utente

Orgapack

Orgapack OR-T 85 Guida rapida

TOUGHCUT

TOUGHCUT Diamond 400 Manuale utente

Yaros

Yaros PB-3603 Manuale utente

Fein

Fein BSS 2.0 E Guida all'installazione

Baileigh Industrial

Baileigh Industrial SS-2725 Manuale utente

Milwaukee

Milwaukee 2674-20 Manuale utente

Fein

Fein BLs 1.6 Manuale utente

Princess

Princess Electric Multi Sharpener Manuale utente

FOREDOM

FOREDOM K.1050 Manuale