Clarke CBS16 Manuale di istruzioni

OPERATION & MAINTENANCE

INSTRUCTIONS

LS0910

ELECTRIC DRILL BIT SHARPENER

MODEL NO: CBS16

PART NO: 6480230

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

INTRODUCTION

Thank you for purchasing this CLARKE electric drill bit sharpener.

Before attempting to use this product, please read this manual thoroughly and

follow the instructions carefully. In doing so you will ensure the safety of yourself

and that of others around you, and you can look forward to your purchase

giving you long and satisfactory service.

IMPORTANT

Please read all of the safety and operating instructions carefully before using this

product. Please pay particular attention to all sections of these instructions that display

warning symbols and notices.

GUARANTEE

This product is guaranteed against faulty manufacture for a period of 12

months from the date of purchase. Please keep your receipt which will be

required as proof of purchase.

This guarantee is invalid if the product is found to have been abused or

tampered with in any way, or not used for the purpose for which it was

intended.

Faulty goods should be returned to their place of purchase, no product can

be returned to us without prior permission.

This guarantee does not effect your statutory rights.

WARNING! This is a Warning symbol. This symbol is used

throughout the user guide whenever there is a risk of personal

injury. Ensure that these warnings are read and understood at all

times.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

GENERAL SAFETY RULES

1. KEEP WORK AREA CLEAN. Cluttered areas invite injuries. Keep work area well lit.

2. NEVER use power tools in damp, wet, or poorly lit locations. Don't expose to rain. Do

not use electrically powered tools in the presence of flammable gases or liquids.

3. KEEP CHILDREN AWAY. Children must never be allowed in the work area. Do not let

them handle machines, tools, or extension cable.

4. STORE IDLE EQUIPMENT. When not in use, tools must be locked up in a dry location to

inhibit rust. Always lock up tools and keep out of reach of children.

5. DO NOT FORCE THE TOOL. It will do the job better and more safely at the rate for

which it was intended.

6. DRESS PROPERLY. Do not wear loose clothing or jewellery which could be caught in

moving parts.

7. USE EYE AND HAND PROTECTION. Always wear approved impact safety goggles.

8. DO NOT ABUSE THE POWER CABLE. Do not yank it to disconnect it from the socket. Do

not carry tools by the cable.

9. DISCONNECT POWER. Unplug when not in use, before servicing, and when changing

accessories.

10. AVOID UNINTENTIONAL STARTING. Be sure the switch is in the OFF position when not in

use and before plugging in.

11. STAY ALERT. Watch what you are doing, use common sense. Do not operate any tool

when you are tired.

12. CHECK DAMAGED PARTS. Before using any tool, any part that appears damaged

should be carefully checked to determine that it will operate properly and perform

its intended function. Do not use the tool if the switch does not turn on and off

properly.

13. GUARD AGAINST ELECTRIC SHOCK. Prevent body contact with grounded surfaces

such as pipes, radiators.

14. REPLACEMENT PARTS AND ACCESSORIES. When servicing, use only identical

replacement parts. Use of any other parts will void the warranty. Only use

accessories intended for use with this tool.

15. DO NOT OPERATE TOOL IF UNDER THE INFLUENCE OF ALCOHOL OR DRUGS. If there is

any doubt, do not operate the tool.

16. KEEP AWAY FROM LIQUIDS. Tool is designed for dry sharpening operations only.

17. HEAT PRODUCED WHEN SHARPENING. The sharpening head and any bits being

sharpened will become hot. Be careful when handling; allow drill tips to cool before

storing.

WARNING: WHEN USING ELECTRIC TOOLS, MACHINES, OR EQUIPMENT,

BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO REDUCE

THE RISK OF FIRE, ELECTRIC SHOCK, AND PERSONAL INJURY.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

ELECTRICAL CONNECTIONS

Before switching the product on, make sure that the voltage of your electricity supply is

the same as that indicated on the rating plate. This product is designed to operate on

230VAC 50Hz. Connecting it to any other power source may cause damage.

This product may be fitted with a non-rewireable plug. If it is necessary to change the

fuse in the plug, the fuse cover must be refitted. If the fuse cover becomes lost or

damaged, the plug must not be used until a suitable replacement is obtained.

If the plug has to be changed because it is not suitable for your socket, or due to

damage, it should be cut off and a replacement fitted, following the wiring instructions

shown below. The old plug must be disposed of safely, as insertion into a mains socket

could cause an electrical hazard.

If the colours of the wires in the power cable of this product do not correspond with the

markings on the terminals of your plug, proceed as follows.

• The wire which is coloured Blue must be connected to the terminal which is

marked Nor coloured Black.

• The wire which is coloured Brown must be connected to the terminal which is

marked Lor coloured Red.

We strongly recommend that this machine is connected to the mains supply via a

Residual Current Device (RCD)

If in any doubt, consult a qualified electrician. DO NOT attempt any repairs yourself.

This symbol indicates that this is a Class II product, and does not require an earth

connection.

WARNING! Read these electrical safety instructions thoroughly

before connecting the product to the mains supply.

WARNING! The wires in the power cable of this product are

coloured in accordance with the following code:

Blue = Neutral Brown = Live

Plug must be BS1363/A approved.

Always fit a 5 Amp fuse.

Ensure that the outer sheath of the cable is firmly held by the clamp

Neutral

(Blue)

Live

(Brown)

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

PRODUCT OVERVIEW

NO DESCRIPTION

1 Grinding Wheel Height Adjustment Knob

2 Head Assembly

3On/OffSwitch

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

OPERATIONS

PROPERLY SHARPENED BITS

Your bit is properly sharpened when it has the following characteristics.

• A sharp point in the center of the bit.

• Two sharp and equal cutting edges

• Two trailing edges that are slightly lower than the cutting edges.

SHARPENING PROCEDURE

1. Place sharpener on a flat, sturdy surface and plug in.

2. Put a single drill bit (HSS only) into

the appropriate hole

3. Turn the unit on.

• Exert a slight downward

pressure onto the bit and rotate

the bit back and forth about 20

degrees while sharpening.

• The bit must be kept in motion

whilst in the machine.

4. Turn unit off after approximatley 5-10 seconds of sharpening.

• Examine bit according to the “Sharpening Hints” section below.

5. Ensure both sides of the drill bit are sharpened using the same amount of

time and pressure.

6. Repeat the above steps as necessary.

7. Do not run the machine for longer than 2 minutes at a time.

SHARPENING HINTS

• If the tip of bit starts to turn blue, it is overheating. Reduce the

amount of pressure and sharpening time. Cool the bit in water

between sharpening cycles.

• If one edge is longer than the other, sharpen the drill bit a little more.

• If you are sharpening a broken (rather than blunt) bit and the time

required to restore the shape is too long, rough the bit into shape first

using a bench grinder.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

ADJUSTING THE GRINDING WHEEL

1. Turn the grinding wheel height

adjustment knob clockwise to

raise the wheel.

• This will give you an aggressive

cutting action. This is also useful

when you are working with

short bits.

2. Lower the wheel by turning the

adjusting knob to the left.

• This will produce a finer ground

edge, though it will take longer and require more repetitions.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

MAINTENANCE

CHANGING THE WHEEL

1. Make sure that the sharpener is switched off and disconnected from the

mains power supply.

2. Remove the two screws that hold

the head assembly in place and

remove the head assembly.

3. Remove the wheel assembly.

• Make sure the spring

underneath stays in place.

4. Unscrew the adjustment cylinder

from the wheel base by turning

clockwise.

5. Prise out the washer (#6).

6. Pop out the wheel base and

remove the worn grinding wheel.

7. Press new grinding wheel onto the

wheel base, replace the washer,

and screw the adjustment

cylinder back in.

8. Replace wheel assembly onto the

unit.

• Make sure that the inner flats of

the adjustment cylinder line up

with the outer flats of the drive spindle.

9. Replace the head assembly and screws.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

CLEANING

1. Keep the surface of your sharpener free of grit, dirt, and grease. Use soapy

water or non-toxic solvents. Do not use petroleum based solvents.

2. Keep the air vents free of foreign matter at all times.

3. If the motor does not operate, it needs to be serviced or replaced by a

qualified technician.

TROUBLESHOOTING

If the motor turns on, but the wheel does not spin, make sure the adjustment

cylinder's inner flats line up with the outer flats of the spindle as described in

“Changing The Wheel” on page 8.

SPECIFICATION

Model Number CSB16

Voltage 230 V @ 50Hz

Operating Temperature -15oC - +40oC

Drill Bit Sizes And Type 3.0 mm to 10 mm HSS

Duty Cycle S3 20% (2 minutes on, 8 minutes off)

No Load Speed 1600 rpm

Sound Pressure Level (LpA dB) 61 dB(A)

Guaranteed Sound Power (LwA dB) 74 dB(A)

Dimensions (L x W x H) 140 x 130 x 240 mm

Weight 2.2 Kg

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

PARTS LIST AND DIAGRAM

ID DESCRIPTION PART NO ID DESCRIPTION PART NO

4A Adjustment Knob HTCBS1604A 16 Connector (Male) HTCBS16016

1 Index HTCBS16001 17 Upper Motor Housing HTCBS16017

2 Cap Ring HTCBS16002 18 Bolt HTCBS16018

5 Adjustment Cylinder HTCBS16005 19 Motor HTCBS16019

6 Washer HTCBS16006 20 Cover HTCBS16020

7 Grinding Wheel HTCBS16007 21 Terminal HTCBS16021

8 Wheel Base HTCBS16008 22 Capacitor HTCBS16022

9 Spring HTCBS16009 23 Lower Motor Housing HTCBS16023

10 Screw HTCBS16010 24 Switch HTCBS16024

11 Cover HTCBS16011 25 Screw HTCBS16025

12 Housing HTCBS16012 26 Cable HTCBS16026

13 Ball Bearing HTCBS16013 27 Rubber Pad HTCBS16027

14 Drive Spindle HTCBS16014 28 Screw HTCBS16028

15 Nut HTCBS16015

Indice

Altri manuali Clarke Utensili elettrici

Clarke

Clarke METALWORKER CBS20 Manuale utente

Clarke

Clarke ECSS2 Manuale di istruzioni

Clarke

Clarke cp185 Manuale di installazione e funzionamento

Clarke

Clarke Contractor CON15 Manuale di installazione e funzionamento

Clarke

Clarke Metalworker CDP350V Manuale di installazione e funzionamento

Clarke

Clarke Air CAT105 Manuale di istruzioni

Clarke

Clarke CJS380 Manuale di installazione e funzionamento

Clarke

Clarke Air 25C Manuale di installazione e funzionamento

Clarke

Clarke CAG120 Manuale di installazione e funzionamento

Clarke

Clarke Strong-arm AHP 16 Manuale di istruzioni

Clarke

Clarke Air CSG3KC Manuale di installazione e funzionamento

Clarke

Clarke CCRT266 Manuale di istruzioni

Clarke

Clarke Strong-Arm AHP 26 Manuale di istruzioni

Clarke

Clarke Metalworker CDP101B Manuale di installazione e funzionamento

Clarke

Clarke CAT84 Guida alla risoluzione dei problemi

Clarke

Clarke Metalworker CDP202B Manuale di istruzioni

Clarke

Clarke STRONG-ARM CSA10BB Manuale di istruzioni

Clarke

Clarke CAT21B Manuale di installazione e funzionamento

Clarke

Clarke CAT52 Manuale di installazione e funzionamento

Clarke

Clarke Air CAT63 Manuale di installazione e funzionamento

Clarke

Clarke CPR2 Manuale di installazione e funzionamento

Clarke

Clarke CAT55 Manuale di installazione e funzionamento

Clarke

Clarke DU8 Manuale utente

Clarke

Clarke Air CAT147 Manuale di installazione e funzionamento

Manuali Utensili elettrici popolari di altre marche

AEG

AEG OMNI-JS Manuale utente

SIP

SIP 01533 Manuale utente

Ribimex

Ribimex PRS499 Manuale utente

3M Fiber Optic Connector Crimp Tool Manuale utente

Ryobi

Ryobi P524 Manuale utente

ROJEK

ROJEK FSN 300A Manuale utente

Kemper

Kemper 1740PRO Manuale utente

WABCO

WABCO OptiTire Manuale utente

EINHELL

EINHELL TE-MS 18/210 Li Manuale utente

Orgapack

Orgapack OR-T 85 Guida rapida

TOUGHCUT

TOUGHCUT Diamond 400 Manuale utente

Yaros

Yaros PB-3603 Manuale utente

Fein

Fein BSS 2.0 E Guida all'installazione

Baileigh Industrial

Baileigh Industrial SS-2725 Manuale utente

Milwaukee

Milwaukee 2674-20 Manuale utente

Fein

Fein BLs 1.6 Manuale utente

Princess

Princess Electric Multi Sharpener Manuale utente

FOREDOM

FOREDOM K.1050 Manuale