Clarke CSR4550BO Manuale utente
ASSEMBLY INSTRUCTIONS
GC0516
4-SHELF BOLTLESS SHELVING UNITS
MODEL NO: CSR4550BO
Part No: 6600726
2
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com
INTRODUCTION
Thank you for purchasing this CLARKE Shelving Unit.
Before attempting to use this product, please read this manual thoroughly and
follow the instructions carefully. In doing so you will ensure the safety of yourself
and that of others around you, and you can look forward to your purchase
giving you long and satisfactory service.
Please keep these instructions in a safe place for future reference.
SCOPE
These instructions cover the following models
Description Model Part Number
4-Shelf 500kg Boltless Shelving
Available in blue/orange
CSR4550BO 6600726
3
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com
INVENTORY
No Description Quantity
APost 4
BLongBeam 4
CShortBeam 8
DSupportBeam 8
E Shelf 4
F Metal Foot 4
4
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com
ASSEMBLY ADVICE
1. Assemble on a strong, level surface. Avoid assembly on a domestic carpet.
2. Use a cloth or softwood block to protect the surface finish of the product
when using a mallet. Strike the flat surface of each beam to prevent
damage to the beam.
3. Always ensure that the rivets sit at the bottom of the keyhole slots.
4. It is recommended that the assembly should be done by two persons.
5. Always wear gloves when assembling these units.
6. The shelving unit is not recommended for outdoor use.
ASSEMBLY INSTRUCTIONS
TOOLS REQUIRED
• Rubber mallet or hammer
• Protective cloth/wood block
The tabs of the beams will often enter
the slots fully using just firm hand
pressure but if they are too tight, you
may require a rubber mallet to assist.
If so, always use a cloth to protect
the product paint finish.
Tap gently with the mallet to drive the
tabs of the beams fully into the slots in
the post. Always strike the edge close
to the post.
1. Insert the metal feet (F) into the
end of each post as shown.
5
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com
2. Use the short beams (C) to
connect the front and rear posts
together.
• The edge with the wider flange
should be installed uppermost to
support the shelf.
3. Repeat this again to create the
other end assembly, making sure
that the corresponding beams
are at the same height.
4. Join the two end assemblies
together with the long beams (B)
as shown.
5. Connect the support beams (D) to
the long beams (B) by bending the
flexible tabs to 90 degrees and
passing them througthe slots in the
long beams.
• The tab initially lays flat against the
long beam.
6. Next, bend the tab back through
180 degrees to grip the long
beam.
• Use a screwdriver or similar tool to
bend the tabs.
7. Finally, bend the tab again
through 90 degrees the opposite
way, to seat tightly against the
support beam.
• Ensure there is no movement
between the beams.
6
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com
8. Lay the shelf panels (E) into
position.
• Always assemble the top shelf at
the highest possible position.
9. We recommend that the racking
be secured to an adjacent wall
using typical wall insert plugs and
screws (not supplied) aligned with
the assembly slots in the posts.
GENERAL SAFETY RULES
1. Always maintain equipment in good condition for the best/safest
performance.
2. Never exceed the maximum load for these shelving units as stated in the
specification.
3. Never use these units if they are damaged.
4. Always load small, stable items on the top shelves, heavier and bulky items
should be stored on the lower shelves.
5. Always distribute heavy loads evenly across the shelves.
6. Always locate on a strong, level, floor surface. Allow adequate working
space.
7
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com
SPECIFICATION
GUARANTEE
This product is guaranteed against faulty manufacture for a period of 12
months from the date of purchase. Please keep your receipt which will be
required as proof of purchase.
This guarantee is invalid if the product is found to have been abused or
tampered with in any way, or not used for the purpose for which it was
intended.
Faulty goods should be returned to their place of purchase, no product can
be returned to us without prior permission.
This guarantee does not effect your statutory rights.
ENVIRONMENTAL PROTECTION
Do not dispose of old products or damaged parts with general household
waste. All tools, accessories and packaging no longer required should be
sorted, taken to a recycling centre and disposed of appropriately.
Model Dimensions
(W x D x H)
Weight
(Empty)
Load per
shelf (evenly
distributed)
CSR4550 Unit 1800 x 500 x 2000 mm 46 kg 550 kg
Questo manuale è adatto per i seguenti modelli
1
Indice
Altri manuali Clarke Rack e supporto
Clarke
Clarke Strong-Arm CES340 Manuale utente
Clarke
Clarke CWC80B Manuale utente
Clarke
Clarke CAX3TAB Manuale utente
Clarke
Clarke CAX3TBC Manuale utente
Clarke
Clarke CES680F Manuale del proprietario
Clarke
Clarke Strong-Arm CES450 Manuale utente
Clarke
Clarke CMSS Manuale utente
Clarke
Clarke CWMWR1 Manuale utente
Clarke
Clarke Metalworker CL430 Manuale utente
Clarke
Clarke CUTS1 Manuale utente
Clarke
Clarke CAX20S Manuale utente
Clarke
Clarke CGR1 Manuale utente
Clarke
Clarke CWR1 Manuale utente
Clarke
Clarke CSM5175 Series Manuale utente
Clarke
Clarke CSM4200 Manuale utente
Clarke
Clarke CES560 Manuale utente
Clarke
Clarke CDS3 Manuale utente
Clarke
Clarke CHT399 Manuale di istruzioni
Clarke
Clarke CSP420 Manuale utente
Clarke
Clarke CTA150 Manuale utente
