Clarke CDDFTP Manuale utente

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

MODEL NO: CDDFTP

PART NO:

PART NO: 6499680

Fuel Transfer Pump

INTRODUCTION

Thank you for purchasing this CLARKE Double Diaphragm Fuel Transfer Pump,

This pump is designed for use with non-corrosive petroleum based products of light to medium viscosity such as petrol,

diesel,fuel oil and motor oils. It should not be used with solvents,acids,alkalis,or other corrosive liquids

Before attempting to use this product, please read this manual thoroughly and follow the instructions carefully.

SAFETY

To ensure safe and efficient operation, it is essential to read and follow each of these warnings and precautions.

1. When used to pump flammable liquids, improper use or installation of this product can cause serious bodily injury or

death.

2. Do NOT smoke near the pump or use the pump near an open flame. Fire could result.

3. When pumping flammable liquids, all equipment must be grounded to prevent the build up of static electricity

which may ignite vapours or gases. The pump and containers should be connected using bonding clamps or clips

and a conductive wire no smaller than 12 gauge. A secure and positive metal to metal contact must be made. The

other end of the wire should be attached to a good ground, such as a steel building column or water pipe.

SPECIFICATIONS

GUARANTEE

This product is guaranteed against faulty manufacture for a period of 12 months from the date of

purchase. Please keep your receipt which will be required as proof of purchase.

This guarantee is invalid if the product is found to have been abused or tampered with in any way, or not

used for the purpose for which it was intended.

Faulty goods should be returned to their place of purchase, no product can be returned to us without prior

permission.

This guarantee does not effect your statutory rights.

Barrel Collar Size 2” BSP Outlet Tube Diameter 27 mm

Inlet Tube Diameter 26 mm Product Weight 5.6 kg

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

ASSEMBLY

FITTING THE PUMP TO A BARREL

1. Assemble the pump as shown above. Use PTFE tape (not supplied) at all connections

2. Screw the threaded collar into the opening of the barrel.

3. Tighten the collar bolt to the pump body.

USING THE PUMP

1. Make sure all connections are secure and place a suitable container under the spout.

2. Pump the handle to draw fluid from the barrel.

• The first time you use the pump, liquid should begin flowing after several pumps of the handle

CLEANING THE FILTER

1. Remove the four bolts that connect the Inlet to the pump.

2. Remove the filter holder and filter.

3. Wash the filter of any contaminants.

4. Replace the filter holder and filter.

5. Reattach the Inlet and secure with the four bolts.

WHAT IS SUPPLIED ASSEMBLED

CAUTION: DO NOT USE THE PUMP IF THE FILTER. IS DAMAGED OR

BLOCKED.

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Clarke Pompa dell'acqua

Clarke

Clarke PSV3A Manuale di istruzioni

Clarke

Clarke CSV1A Manuale di istruzioni

Clarke

Clarke IVP13A Manuale di installazione e funzionamento

Clarke

Clarke CWP1000A Manuale di istruzioni

Clarke

Clarke CWP200 Manuale di istruzioni

Clarke

Clarke CBT1300SS Manuale di istruzioni

Clarke

Clarke CPE20A1 Manuale di istruzioni

Clarke

Clarke Hippo4A Manuale di istruzioni

Clarke

Clarke CPPRSS Manuale utente

Clarke

Clarke MSP12 Manuale utente

Clarke

Clarke DFT12A Manuale di istruzioni

Clarke

Clarke BPT600 Manuale di installazione e funzionamento

Clarke

Clarke HIPPO Jr Manuale di installazione e funzionamento

Clarke

Clarke BIP1000 Manuale di istruzioni

Clarke

Clarke CPE15S Manuale di istruzioni

Clarke

Clarke CSP1530 Manuale di istruzioni

Clarke

Clarke CM1 Manuale di installazione e funzionamento

Clarke

Clarke CBM100SS Manuale di installazione e funzionamento

Clarke

Clarke ISP10A Manuale di installazione e funzionamento

Clarke

Clarke ISP11A Manuale

Clarke

Clarke CU150 Manuale di installazione e funzionamento

Clarke

Clarke TAM100 7230035 Manuale di installazione e funzionamento

Clarke

Clarke STP12 Manuale di istruzioni

Clarke

Clarke CBM100SS Manuale di istruzioni

Manuali Pompa dell'acqua popolari di altre marche

Neptun

Neptun NPHW 5500 Manuale utente

Sensidyne

Sensidyne Gilian BDX-II Istruzioni per l'installazione e il funzionamento

Draper

Draper 47808 Manuale utente

Trolla

Trolla 12820 Manuale utente

Sunfab

Sunfab SVH Series Manuale utente

WilTec

WilTec 50740 Manuale utente

Fieldmann

Fieldmann FVC 5015 EK Manuale utente

Everbilt

Everbilt EFSUB5-122HD Manuale utente

Graco

Graco Husky 3300e Manuale utente

esotec

esotec 101018 Manuale utente

moyno

moyno 2000 CC Manuale utente

Becker

Becker BASIC VASF 2.80/1-0.AC230 Manuale utente

Sykes AmeriPumps

Sykes AmeriPumps GP100M Guida alla risoluzione dei problemi

DUROMAX

DUROMAX XP WX Series Manuale utente

BRINKMANN PUMPS

BRINKMANN PUMPS SBF550 Manuale utente

Franklin Electric

Franklin Electric IPS Manuale utente

Xylem

Xylem e-1532 Series Manuale utente

Milton Roy

Milton Roy PRIMEROYAL Manuale utente