Clarke CTL24/3 Manuale utente

INSTRUCTION MANUAL

GC0609

3 X 24w WORK LAMP

Model: CTL24/3

Part No: 4002910

INTRODUCTION

Thank you for purchasing this CLARKE Work Lamp.

Before attempting to operate the product, it is essential that you read this

manual thoroughly and carefully follow all instructions given. In doing so you

will ensure the safety of yourself and that of others around you, and you can

also look forward to the product giving you long and satisfactory service.

GUARANTEE

This CLARKE product is guaranteed against faulty manufacture for a period of

12 months from the date of purchase. Please keep your receipt as proof of

purchase.

This guarantee is invalid if the product is found to have been abused or

tampered with in any way, or not used for the purpose for which it was

intended.

Faulty goods should be returned to their place of purchase, no product can

be returned to us without prior permission.

This guarantee does not effect your statutory rights.

ENVIRONMENTAL PROTECTION

Do not dispose of this product with general household waste. All tools,

accessories and packaging should be sorted, taken to a recycling

centre and disposed of according to the laws governing Waste

Electrical and Electronic Equipment.

SPARES & SERVICE CONTACTS

For parts & servicing, please contact your nearest dealer, or

CLARKE International, on one of the following numbers.

PARTS & SERVICE TEL: 020 8988 7400

PARTS & SERVICE FAX: 020 8558 3622

or e-mail as follows:

PARTS: [email protected]

SERVICE: [email protected]

GENERAL SAFETY PRECAUTIONS

WORK ENVIRONMENT

1. ALWAYS keep the work area clean and tidy.

2. ALWAYS keep children and bystanders away from the work area.

3. Although the lamp may be used outdoors, DO NOT leave it exposed to

the elements. Avoid direct sunlight, direct heat, rain/moisture etc.

4.ALWAYS keep body and clothing dry. Never work in damp area without

adequate insulation against electric shock.

GENERAL USE

1. ALWAYS check for damage before using the lamp. Inspect the power

cable and plug for damage and ensure that no connections are loose.

Any damage should be properly repaired or the part replaced. Consult

your CLARKE dealer.

2. NEVER modify the plug in any way. Do not use adaptor plugs with earthed

(grounded) power tools. Correct plugs and outlets will reduce the risk of

electric shock.

3. ALWAYS disconnect from the mains supply before moving or performing

any maintenance.

4. NEVER move the lamp with wet hands or when standing on a wet or

damp surface.

5. ALWAYS use an external weatherproof socket when using the lamp

outdoors.

6. NEVER abuse the mains cable or wrench the cable to disconnect it from

the socket. Keep the cable away from sharp edges/hot surfaces.

7. NEVER cover the lamp.

8. ALWAYS disconnect from the power supply when not in use.

9NEVER immerse the lamp in water.

10. ALWAYS store this product in a dry, secure place out of reach of children.

11. NEVER carry out any alterations or modifications to this product.

12. NEVER use this product if it is defective/operating abnormally.

13. NEVER attempt any repairs yourself. If you have a problem with this

product contact your local CLARKE dealer.

Please keep these instructions in a safe place for future reference.

ELECTRICAL CONNECTIONS

Connect the mains lead to a standard, 230 Volt /50Hz electrical supply

through an approved 13 amp BS1363 plug, or a suitably fused isolator switch.

WARNING: THIS APPLIANCE MUST BE EARTHED

IMPORTANT: The wires in the mains lead should be wired up in accordance

with the following colour code:

Green & Yellow - Earth

Blue - Neutral

Brown - Live

•

Connect the GREEN & YELLOW coloured cord to the plug

terminal marked with a letter E or Earth “ “ symbol or

coloured GREEN or GREEN & YELLOW.

• Connect the BROWN coloured cord to the plug terminal

marked a letter “L” or coloured RED.

•

Connect the BLUE coloured cord to the plug terminal marked

a letter “N” or coloured BLACK

If this appliance is fitted with a plug which is moulded on to the electric cable

(i.e. non-rewireable) please note:

1. The plug must be thrown away if it is cut from the electric cable. There is a

danger of electric shock if it is subsequently inserted into a socket outlet.

2. Never use the plug without the fuse cover fitted.

3. Should you wish to replace a detachable fuse carrier, ensure that the

correct replacement is used (as indicated by marking or colour code).

4. Replacement fuse covers can be obtained from your local Clarke dealer

or most electrical stockists.

FUSE RATING

The fuse in the plug must be replaced with one of the same rating and this

replacement must be ASTA approved to BS1362.

We strongly recommend that this machine is connected to the mains supply

via a Residual Current Device (RCD).

If in any doubt, consult a qualified electrician. DO NOT attempt any electrical

repairs yourself.

TECHNICAL SPECIFICATION

Please note that the details and specifications contained herein, are correct

at the time of going to print. However, CLARKE International reserve the right

to change specifications at any time without prior notice.

USE OF THE WORK LAMP

The folding carrying handle can be used to support the lamp on the floor, or

as a hook to suspend the lamp.

Use the holes to facilitate fitting to a flat surface using suitable screws or bolts

(not supplied).

The pair of splashproof sockets fitted to the rear of the worklamp can be used

as extension sockets (max total 13 amps) for secondary applications in dry

conditions. *The IP54 (splash & dustproof) rating only applies when the sockets

are closed and the product is used with an external waterproof socket.

SPARE PARTS

erutaeF noitacificepS

thgieWgk0.4

)hxwxd(snoisnemiD mm524x582x511

htgnelelbacylppuSmm0564

egatlovtupnI zH05/V032

sebut

tnecseroulF )11G2(W42x3

tuptuothgiL mm003@xul0865

ssalCnoitalusnI*45PI

noitpircseD oNtraP noitpircseD oNtraP

retratS10082LTCKNKtsallaB40082LTCKNK

ebuTtnecseroulF20082LTCKNKrevoCtnerapsnarT50082LTCKNK

elbaCsniaM300

82LTCKNKdnuorruSrebbuR60082LTCKNK

MAINTENANCE

• Keep the work lamp clean by wiping with a dry cloth. DO NOT use

solvents as a cleaning agent.

• Check the power cable to ensure it is sound & free from cuts/

cracks etc.

TO REPLACE A FLUORESCENT TUBE OR LAMP STARTER:

Before attempting to replace a fluorescent tube, ensure the work lamp is

switched off and isolated from the electrical supply by unplugging from the

socket. Allow the work lamp to cool down for a few minutes after switching

off, before performing any maintenance tasks. Handle the lamp tubes using

either a glove or a

piece of cloth.

1. Pull off the rubber

surround from

around the lamp

and lift away the

clear front cover.

2. Remove the upper

retaining clip (1)

from the top of the

lamp by sliding

upwards.

3. Remove the lower

retaining clip (2) by

sliding upwards.

4. Release the

fluorescent tube

from the upper

spring clip (3) and

pull the tube

upwards from the

connecting socket.

5. Replacing the tube

is a reverse of the above process, taking care that the four pins of the

lamp line up with the corresponding four holes inside the connecting

socket.

6. To remove a defective starter (4), simply twist it gently anti-clockwise and

pull it from the socket. Gently twist clockwise to replace.

DECLARATION OF CONFORMITY

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Clarke Luce da lavoro

Clarke

Clarke HLC400T Manuale del proprietario

Clarke

Clarke COB10C Manuale del proprietario

Clarke

Clarke COB10CR Manuale utente

Clarke

Clarke UBL1600R Manuale utente

Clarke

Clarke MFL800R Manuale utente

Clarke

Clarke RWL36LI Manuale utente

Clarke

Clarke SMD4500 Manuale utente

Clarke

Clarke SMD84T/110 Manuale del proprietario

Clarke

Clarke CL6FS Manuale utente

Clarke

Clarke GWL700R Manuale utente

Clarke

Clarke LED1000R Manuale utente

Clarke

Clarke SMD84T Manuale del proprietario

Clarke

Clarke COB10T Manuale del proprietario

Clarke

Clarke RWL30 Manuale utente

Clarke

Clarke SMD42C Manuale del proprietario

Clarke

Clarke HLC400/110 Manuale del proprietario

Clarke

Clarke SMD2700L Manuale utente

Clarke

Clarke COB10C/110 Manuale del proprietario

Clarke

Clarke CFL20Li Manuale di istruzioni

Clarke

Clarke SMD42T/110 Manuale del proprietario

Clarke

Clarke LED700SR Manuale utente

Clarke

Clarke HLC400 Manuale del proprietario

Clarke

Clarke HLC400T/110 Manuale del proprietario

Clarke

Clarke SMD42T Manuale del proprietario

Manuali Luce da lavoro popolari di altre marche

ANSMANN

ANSMANN POWERLIGHT 5.1 Manuale utente

RTRMAX

RTRMAX RTX1868 Manuale utente

FeinTech

FeinTech LAL00220 Manuale utente

Bunker Hill Security

Bunker Hill Security 64735 Manuale utente

Goobay

Goobay 30450 Manuale utente

REV Ritter

REV Ritter SPOT Manuale utente

Ignition

Ignition Stagepix Line 100 IP Manuale utente

SCANGRIP

SCANGRIP DUO CONNECT Manuale utente

Bosch

Bosch GLI 18 V Manuale utente

Bayco

Bayco SL-1514 Manuale utente

EUFAB

EUFAB SMD LED 8+1 Manuale utente

DeWalt

DeWalt DCL510 Manuale utente

PowerSmith

PowerSmith PWLD080T Manuale utente

MaxLite

MaxLite 73683 Manuale utente

Heitronic

Heitronic Trend 27867 Manuale utente

Monzana

Monzana Gore MZCL10 Manuale utente

EINHELL

EINHELL TE-CL 18/2000 LiAC Manuale utente

Bayco

Bayco NIGHTSTICK Dual-Light Xtreme Lumens... Manuale utente