Clear-Com FreeSpeak II Integra Manuale utente

User Guide

FreeSpeak II Integra

User Guide

Eclipse HX 10.0 and above

Part Number: 399G262 Rev A

Date: July 31, 2018

User Guide| FreeSpeak II Integra

Document reference

FreeSpeak II Integra User Guide

399G262 Rev A

Legal disclaimers

Clear-Com, the Clear-Com logo, and Clear-Com Concert are trademarks or

registered trademarks of HM Electronics, Inc.

The software described in this document is furnished under a license agreement

and may be used only in accordance with the terms of the agreement.

The product described in this document is distributed under licenses restricting its

use, copying, distribution, and decompilation / reverse engineering. No part of this

document may be reproduced in any form by any means without prior written

authorization of Clear-Com, an HME Company.

Clear-Com Offices are located in California, USA; Cambridge, UK; Dubai, UAE;

Montreal, Canada; and Beijing, China. Specific addresses and contact information

can be found on Clear-Com’s corporate website: www.clearcom.com

Clear-Com contacts:

Americas and Asia-Pacific Headquarters

California, United States

Tel: +1 510 337 6600

Email: CustomerServicesUS@clearcom.com

Europe, Middle East, and Africa Headquarters

Cambridge, United Kingdom

Tel: +44 1223 815000

Email: CustomerServicesEMEA@clearcom.com

China Office

Beijing Representative Office

Beijing, P.R. China

Tel: +8610 65811360/65815577

Page 2

User Guide| FreeSpeak II Integra

Table of contents

1 Important Safety instructions 5

1.1 Safety symbols 6

2 Introduction to FreeSpeak II® 7

2.1 An FS II communication system 7

2.2 FreeSpeak II with an FSII Transceiver (1.9 and 2.4) 11

2.3 FreeSpeak II with an FSII IP Transceiver 11

2.4 FSII 1.9 GHz/FSII 2.4 GHz 13

2.5 National Radio Carrier Frequencies 14

3 Installing a system 16

3.1 Installing and removing an E-IPA-HX card 16

3.2 Adding an E-IPA-HX card to the software 16

3.3 Adding the E-Que card for an FS II transceiver or splitter to the matrix 17

3.4 Connecting to transceivers 20

4 Operating the wireless beltpack 23

4.1 Overview of the wireless beltpack 23

4.2 Beltpack user controls 26

4.3 Using the beltpack 31

5 Programming on the beltpack 37

5.1 Introduction to programming on the beltpack 37

5.2 Configuring the beltpack volume settings 39

5.3 Configuring the beltpack headset 41

5.4 Configuring the beltpack microphone 42

5.5 Configuring the beltpack display and LEDs 43

5.6 Configuring the beltpack alarm options 44

5.7 Selecting the beltpack role default set 47

5.8 Selecting the beltpack administration 47

5.9 Setting the listen again option 48

5.10 Control audio on keys C & D (beltpack)(advanced menu option only) 49

5.11 Accessing beltpack information 50

5.12 Setting display mode 50

5.13 Setting system connect 50

5.14 Enabling over the air (OTA) registration mode from a beltpack 51

5.15 Performing a site survey 52

6 Operating the FS II IP Transceiver (IPT) 53

Page 3

User Guide| FreeSpeak II Integra

6.1 FS II IP Transceiver 53

7 Operating the FS II Transceiver 75

7.1 FS II Transceiver 75

8 Transceiver splitter (PD2203) 92

8.1 PD2203 Front connector panel 92

8.2 Matrix connection indicator light 92

8.3 Matrix connector 92

8.4 Splitter-to-transceiver signal indicator light 93

8.5 Transceiver connectors 93

8.6 PD2203 rear panel 93

8.7 Serial data connector 93

8.8 Power Indicator 94

8.9 DC IN power connector 94

8.10 EXP IN connector 94

8.11 EXP OUT connector 94

8.12 Connecting a transceiver splitter 94

9 Specifications 95

9.1 FreeSpeak II Beltpack 95

9.2 FreeSpeak II IP Transceiver 96

9.3 FreeSpeak II Transceiver 96

9.4 FreeSpeak II Transceiver Splitter 97

9.5 Transmission Method 97

9.6 Notice about specifications 98

10 Regulatory compliance 99

Page 4

User Guide| FreeSpeak II Integra

1 Important Safety instructions

lRead these instructions.

lKeep these instructions.

lHeed all warnings.

lFollow all instructions.

lDo not use this apparatus near water.

lClean only with dry cloth.

lDo not block any ventilation openings. Install in accordance with the

manufacturer’s instructions.

lDo not install near any heat sources such as radiators, heat registers, stoves,

or other apparatus (including amplifiers) that produce heat.

lDo not defeat the safety purpose of the polarized or grounding-type plug. A

polarized plug has two blades and a third grounding prong. The wide blade or

the third prong is provided for your safety. If the provided plug does not fit

into your outlet, consult an electrician for replacement of the obsolete outlet.

lProtect the power cord from being walked on or pinched particularly at plugs,

convenience receptacles, and the point where they exit from the apparatus.

lOnly use attachments/accessories specified by the manufacturer.

lUse only with the cart, stand, tripod, bracket, or table specified by the

manufacturer, or sold with the apparatus. When a cart is used, use caution

when moving the cart/apparatus combination to avoid injury from tip-over.

lUnplug this apparatus during lightning storms or when unused for long periods

of time.

lRefer all servicing to qualified service personnel. Servicing is required when

the apparatus has been damaged in any way, such as power-cord supply or

plug is damaged, liquid has been spilled or objects have fallen into the

apparatus, the apparatus has been exposed to rain or moisture, does not

operate normally, or has been dropped.

lUse only chargers provided by HME/Clear-Com to charge the battery packs or

beltpacks. These include:

lBAT60 Battery pack and beltpack charger manufactured by HME/Clear-

Com

Page 5

User Guide| FreeSpeak II Integra

lUSB Charger model PA1015-050SIB200/PA1015-1SI/ PA1015-

1SI050200 provided by HME/Clear-Com with your beltpack.

lThis product uses Lithium Ion Batteries which can be a fire hazard, if used

improperly. Use only HME/Clear-Com supplied BAT60 or equivalent battery

packs to ensure safe operation of the beltpack.

lWhen using AA Batteries follow all safety instructions from manufacturer. Do

not mix different battery chemistries. When depleted, replace all batteries.

lThe in-beltpack USB charging feature has only been tested utilizing USB2.0

port.

Warning: To reduce the risk of fire or electric shock, do not expose this product to

rain or moisture.

1.1 Safety symbols

Familiarize yourself with the safety symbols. These symbols are displayed on the

apparatus and warn you of the potential danger of electric shock if the system is

used improperly.

Note: For compliance notices, see Regulatory compliance on page 99.

Page 6

User Guide| FreeSpeak II Integra

2 Introduction to FreeSpeak II®

With a FreeSpeak II (FS II) wireless beltpack you can roam freely around a site or

facility while talking and listening to all, or selected, members of the production

team. With its four communication routes, the beltpack gives you the flexibility to

communicate quickly and seamlessly with individuals or groups, and to change

communication routes as often as needed.

With FS II you can set up a wireless system specifically tailored to local needs by

locating transceivers and beltpacks in areas where they are needed most. And

because the beltpacks operate in the unlicensed 1.90 and 2.4 GHz frequency

spectrum, there is no interference with existing wireless systems, even those

located in the same area.

FreeSpeak II offers a choice of two transceivers:

lFS II transceiver that operates using E1 digital transmission

lFS II IP transceiver (IPT) that leverages your existing IP infrastructure for

convenience and ease of installation.

With FreeSpeak II Integra, wireless beltpack users can communicate with any

Eclipse HX panel users on a one-to-one or group basis.

Note: This User Guide covers the use of FS II with a matrix only (FS II Integra). For more

information on running an FS II system with a Base station, please see FreeSpeak II

User Guide, Base Station Version.

To use FreeSpeak II with a matrix, the matrix must be equipped with

lE-IPA-HX cards for connection to FS II IP transceivers

lE-Que cards in transceiver or splitter mode for connection to FS II

transceivers.

The system must be configured using the Eclipse HX Configuration Software. For

more detail, please refer to the Eclipse HX Configuration Software User Guide.

Note: You cannot configure FreeSpeak and FreeSpeak II on the same Eclipse matrix. If

you attempt to do so, the Eclipse HX Configuration Software displays a warning.

2.1 An FS II communication system

An FS II system consists of three main elements:

lThe wireless beltpacks.

Page 7

User Guide| FreeSpeak II Integra

lAn Eclipse HX matrix (Omega, Median or Delta) with an E-IPA-HX card or E-

Que card.

lThe transceiver network that provide custom coverage zones in which

beltpacks can operate. Beltpacks can roam freely between coverage zones.

FS II also includes a drop-in battery charger for the beltpack Li-Ion batteries. You

can conveniently charge the battery by placing the whole beltpack into the charger,

or by placing individual batteries into the charger.

FS II operates using a cellular network of transceivers located around a working

environment. The transceivers connect to the matrix via an E-IPA-HX or E-Que card

installed on the matrix. Each transceiver provides an area or cell in which up to ten

full-duplex beltpacks can operate.

Beltpacks can roam among and between cells without disconnecting because each

beltpack continually detects which transceiver has the strongest available signal.

When the signal from a transceiver starts to diminish due to the distance from a

beltpack, the beltpack automatically “hands off” its signal to the nearest

transceiver, ensuring smooth transfer.

Page 8

User Guide| FreeSpeak II Integra

Page 9

User Guide| FreeSpeak II Integra

Note: The E-IPA-HX card with IP Transceiver offers twice the beltpack density compared

to the E-Que card .

Page 10

Altri manuali per FreeSpeak II Integra

Indice

Altri manuali Clear-Com Sistema di interfono

Clear-Com

Clear-Com SB-440 Manuale utente

Clear-Com

Clear-Com WBS-670 Manuale utente

Clear-Com

Clear-Com FreeSpeak II FSII-TCVR-24 Manuale utente

Clear-Com

Clear-Com KB-111A Guida alla risoluzione dei problemi

Clear-Com

Clear-Com HBP-2X Guida rapida

Clear-Com

Clear-Com CS-100 Guida alla risoluzione dei problemi

Clear-Com

Clear-Com RS-602 Manuale utente

Clear-Com

Clear-Com ICS-102 Manuale utente

Clear-Com

Clear-Com RS-201 Guida alla risoluzione dei problemi

Clear-Com

Clear-Com RM-702-IM Manuale utente

Clear-Com

Clear-Com Encore Manuale utente

Clear-Com

Clear-Com Eclipse HX-PiCo Manuale utente

Clear-Com

Clear-Com FreeSpeak II Manuale utente

Clear-Com

Clear-Com ICS-2003 Manuale utente

Clear-Com

Clear-Com Tempest 2400 MasterBelt Manuale utente

Clear-Com

Clear-Com ECLIPSE-32 MATRIX Manuale utente

Clear-Com

Clear-Com TEMPEST 2400 Manuale utente

Clear-Com

Clear-Com EclipseHX Manuale di installazione e funzionamento

Clear-Com

Clear-Com ENCORE EF-701M Manuale utente

Clear-Com

Clear-Com TEMPEST 2400 Manuale utente

Clear-Com

Clear-Com Eclipse HX-Median Manuale utente

Clear-Com

Clear-Com MS-222 Manuale utente

Clear-Com

Clear-Com Eclipse ICS 1016E Manuale utente

Clear-Com

Clear-Com HME DX210 Manuale utente

Manuali Sistema di interfono popolari di altre marche

Bticino

Bticino LINEA 3000 Manuale utente

MSI

MSI MSI-140 Manuale utente

golmar

golmar Stadio Plus Manuale utente

CyberData

CyberData 011211 series Manuale

Vidos

Vidos duo M1021 Manuale utente

Vimar

Vimar ELVOX 7539/E Manuale utente

SSS Siedle

SSS Siedle BTSV 850-03 Manuale utente

Dahua

Dahua VTO Series Manuale utente

Elvox

Elvox 5651 Manuale utente

Videx

Videx VIDEOKIT Series Manuale utente

Rocom

Rocom Doortello Business FW T2.05W2.04 Manuale utente

Viking

Viking E-35-EWP Manuale utente

Safeguard Supply

Safeguard Supply LRA-EX1000 Manuale utente

SSS Siedle

SSS Siedle BFCV 850 Series Manuale utente

GRD

GRD MAX V2 Manuale utente

Alecto

Alecto ADI-250 Manuale utente

Aiphone

Aiphone IE-8MD Manuale utente

Perel

Perel EDB4 Manuale utente