Clevertronics ARGO-1200 EM Series Specifiche tecniche

1948865

V1.1

18 March 2022

Testing:

Once connected to the 240V mains supply, the unit must be allowed to charge the battery for at least 24

hours. Conduct the following tests:

•For the first test, the emergency lamp must remain illuminated for at least 2 hours after

disconnection from the mains supply.

•Subsequent tests require the unit to illuminate for at least 90 minutes. The results of all tests are

required to be recorded in a service logbook, which is to be kept on-site at all times. If the unit fails

to remain illuminated for the requisite time, remedial action must be taken to repair the situation

and once completed, the unit must pass a subsequent test. For more specific information, please

refer to the current edition of the AS 2293.3 Standard.

•Press and hold Test Button or switch Off Mains Supply, check that the emergency lamp is On.

•Release the Test Button or Switch On Mains Supply, check that the emergency lamp is Off (Non-

maintained operation).

Rated Emergency Lumen Output in accordance with AS2293.1 (refer to

spacing tables for installation positions):

Refer to the Technical Label for classification information.

Caution:

On many building sites, power circuits may be cut off in an uncontrolled and repetitive basis during

construction. As a result, any Exit & Emergency Units, on these circuits, will have their batteries

discharged or “cycled”. The battery in this fitting has been selected to give excellent long-life

performance in a controlled AS2293 testing environment. Excessive battery cycling will reduce through-

life performance and may lead to premature battery failure. Battery warranty claims, as a result of such

abuse, are specifically EXCLUDED from Clevertronics warranty terms.

Warranty:

For Product Warranty information and Terms and Conditions of Sales please refer to our website

http://clevertronics.com.au/terms-conditions-sale-australia-nz/

Trouble Shooting:

Below are a list of common problems and their possible causes.

Fault: The Green LED indicator is not illuminated.

Check: A.C. is connected and is turned on.

Battery is connected

Test Switch for damage.

Fault: Lamp does not illuminate in emergency mode.

Check: A.C. is connected.

Battery is connected

Fault: Lamp illuminates in emergency mode, but only stays on for a short period.

Check: Battery has been allowed to charge for at least 24 hours.

Battery for damage.

Fault: The main LED strip is not illuminated.

Check: A.C. is connected and is turned on.

Wiring connections between the LED driver and LED strip.

Fault: Green LED flashes once every 5 seconds-Battery in disconnected

Check: Battery is connected.

Fault: Green LED blinks off once every 5 seconds- Charging very flat battery

Allow 20min to recover battery then recheck

Fault: Green LED flashes at 2Hz (Fast flash)- Faulty battery

Replace battery

ARGO Weatherproof Emergency LED Batten

Switchable Colour & Output

Installation & Maintenance Instruction Leaflet

Victoria (Head Office & Manufacturing)

Website: www.clevertronics.com.au

Email: info@clevertronics.com.au

Phone: +61 3 9559 2700

Fax: +61 3 9559 2799

New South Wales

Phone: +61 2 8805 6400

Fax: +61 2 8805 6444

Queensland

Phone: +61 7 3442 9700

Fax: +61 7 3442 9777

South Australia/Northern Territory

Phone: +61 8 8301 8800

Fax: +61 8 8351 8286

Western Australia

Phone: +61 8 9207 0000

Fax: +61 8 9207 0088

New Zealand

Phone: +64 800 548 448

Designed in Australia to comply with the

requirements of AS2293.3: 2018, AS CISPR15:

2017, IEC EN 60598-2-22:2014, AS/NZS 60598.2.22:

2019, IEC EN 62471:2006 and IEC EN 62031: 2008 +

A2: 2015.

Models:

ARGO-1200-xxx-EM

Options:

Microwave Sensor (HI/LO)

xxx = SEN

Spare Parts:

AUM03570030001

Replacement Emergency Driver

1560050

Replacement Battery

1330098

Replacement 240V Driver

1330089

Replacement 240V Driver

Important:

It is illegal for anyone, except for a licensed electrician to install or maintain this product. Before installation,

ensure that the electricity supply has been switched off and isolated. Installation must be carried out in

accordance with the relevant Australian and International Standards.

1948865

V1.1

18 March 2022

Installation:

The ARGO-1200-EM-xxx can be mounted to or suspended from any solid surface. Please follow the

below installation steps:

•Determine the installation method (surface/surface with clips) and the power entry method.

•Undo the diffuser clips, remove the diffuser and gear tray. Position the batten base in the desired

location. Mark out the fixing points on the mounting surface.

•If the cable entry is to be via the rear of the body –Drill out a suitable entry-hole in the rear of the

batten body (must be suitably sealed after cable entry using a sealant). If the cable entry is via the

end of the batten - Install the provided cable gland, or bring in conduit, to the base as required for

the intended power access. Note: Only round cables are to be used with the cable gland for an

IP65 seal. Keep cable entry straight and tension free. Ensure all seals are tight.

min. wire diameter 6mm, max. 12mm.

•For surface mounting -, there are 2 extrusions/posts at each end of the base. Drill out the desired

number of fixing points at each end. Fixings must only be through the extrusions/mounting

posts.

oPosition the fitting to the mounting surface and mark the mounting holes.

oDrill the mounting holes.

oFix the base to the surface with appropriate fixings.

oSeal mounting area with appropriate sealant.

•For Surface Mount Clip mounting, measure/mark spacing (see dimensions below), install

stainless steel clips to surface (use appropriate fixings), then snap batten into clips.

•Re-attach battery into Emergency Driver & remove Warning Label from Terminal Block.

•Wire mains power cable, 240V 50Hz, to terminals marked Lsw (Switched Active), Lem

(Emergency/Unswitched Active), N &

•Set LED Driver Power Output to either Low (2000Lm) or High(4000Lm) (non-MS-HL version only)

•Set Colour Switch to the desired colour (3000K, 4000K, 5700K)

•Attach gear tray to lanyards.

•Reinstall the gear tray, diffuser and latch the diffuser clips.

Wiring:

Sensor Version:

Dimensions:

Driver Setting:

(non-SEN version only)

Colour Setting:

Gear Tray Clip:

Battery Replacement

1. Prior to any work, isolate power to any Batten that requires battery replacement

2. Open the Diffuser by releasing the Batten Diffuser Clips (remove any screws that may have been

installed into clips)

3. Unlock the Gear Tray by rotating the Gear Tray Clips 90° in an anti-clockwise direction (ensure the

Gear Tray is supported while unlocking clips)

4. Remove Battery connector from the Emergency Driver

5. Remove Battery and Battery Clips from the Gear Tray (release one side of clips to remove battery

and clips together as one)

6. Install replacement Battery & Clips and connect into Emergency Driver

7. Re-Install the Gear Tray and ensure Clips are locked (rotate clips by 90° clockwise)

8. Re-Install the Diffuser and close all clips (re-install any screws that may have been inserted into the

Diffuser Clips)

Note:

This luminaire (with reinforced insulation between control/LED terminal and AC Supply) contains non-

user replaceable light source and battery –to be replaced (if required, refer installation instructions for

battery replacement) by the manufacturer or his service agent or a similar qualified person.

Altri manuali Clevertronics Attrezzatura di illuminazione

Clevertronics

Clevertronics L10 ARGOPRO-1200-L10POD Series Manuale utente

Clevertronics

Clevertronics LED CIRCLITE Istruzioni per l'installazione e il funzionamento

Clevertronics

Clevertronics Argonaut PLUS Guida alla manutenzione e all'assistenza

Clevertronics

Clevertronics l10 LBULKy Series Istruzioni per l'installazione e il funzionamento

Clevertronics

Clevertronics LIFELIGHT-2PRO-SMS-600 Istruzioni per l'installazione e il funzionamento

Clevertronics

Clevertronics L10 LIFELIGHT PRO LLIFE PRO Series Manuale utente

Clevertronics

Clevertronics L10 LIFELIGHT LLIFE-SM Series Istruzioni per l'installazione e il funzionamento

Clevertronics

Clevertronics L10 LIFELIGHT PRO Manuale utente

Clevertronics

Clevertronics LP Argonaut Manuale di istruzioni

Clevertronics

Clevertronics FVP2LED-P Series Guida alla manutenzione e all'assistenza

Clevertronics

Clevertronics EL EUBPRO-SM-LI Istruzioni per l'installazione e il funzionamento

Clevertronics

Clevertronics L10 LWFLED 2IPREM Series Manuale di istruzioni

Clevertronics

Clevertronics L10 LIFELIGHT LLIFE Series Istruzioni per l'installazione e il funzionamento

Clevertronics

Clevertronics LP LIFELIGHT PRO CLIFE PRO-SMC Series Istruzioni per l'installazione e il funzionamento

Clevertronics

Clevertronics Glider Istruzioni per l'installazione e il funzionamento

Clevertronics

Clevertronics LP Cleverfit Pro CCFPRO Series Istruzioni per l'installazione e il funzionamento

Clevertronics

Clevertronics LP LIFELIGHT-2PRO-SMS-600 Manuale utente

Clevertronics

Clevertronics CleverEVAC LP Cleverfit Pro DYRC CP Series Istruzioni per l'installazione e il funzionamento

Clevertronics

Clevertronics Trade Series Manuale

Clevertronics

Clevertronics LP Cleverfit CCFLED Series Istruzioni per l'installazione e il funzionamento

Clevertronics

Clevertronics L10 LIFELIGHT PRO LLIFE-PRO SPOT Series Istruzioni per l'installazione e il funzionamento

Clevertronics

Clevertronics L10 Cleverfit LCFLED Series Istruzioni per l'installazione e il funzionamento

Clevertronics

Clevertronics LP CFLLED Series Istruzioni per l'installazione e il funzionamento

Clevertronics

Clevertronics L10 LJELED-40 Series Manuale utente

Manuali Attrezzatura di illuminazione popolari di altre marche

Brizo

Brizo 8SP-MU-4 Manuale utente

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Manuale utente

IKEA

IKEA BJÖRKSPIREA Manuale utente

Laserworld

Laserworld Evolution Series ES-400RGB Manuale utente

Alien

Alien RG STAR Manuale utente

EuroLite

EuroLite LED B-40 Manuale utente

Qazqa

Qazqa Suplux SL 3 Black 103062 Manuale utente

Commercial Electric

Commercial Electric 54568141 Manuale utente

CREE LIGHTING

CREE LIGHTING 304 Series Manuale utente

Goobay

Goobay 49867 Manuale utente

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Manuale utente

Alkalite

Alkalite Krypton KT-81 Manuale utente

Clas Ohlson

Clas Ohlson GU10 Manuale utente

DTS

DTS DELTA 10 F Manuale utente

ring

ring Solar Steplight Manuale utente

One Stop Gardens

One Stop Gardens 57696 Istruzioni per il montaggio

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Manuale utente

SIREM

SIREM Swimeo A2 Manuale utente