Cognex In-Sight 7010 Manuale utente

In-Sight®7000 Series

Vision System

Installation Manual

02/21/2017

Version: 5.4.0.19

Legal Notices

The software described in this document is furnished under license, and may be used or copied only in accordance with

the terms of such license and with the inclusion of the copyright notice shown on this page. Neither the software, this

document, nor any copies thereof may be provided to, or otherwise made available to, anyone other than the licensee.

Title to, and ownership of, this software remains with Cognex Corporation or its licensor. Cognex Corporation assumes

no responsibility for the use or reliability of its software on equipment that is not supplied by Cognex Corporation.

Cognex Corporation makes no warranties, either express or implied, regarding the described software, its

merchantability, non-infringement or its fitness for any particular purpose.

The information in this document is subject to change without notice and should not be construed as a commitment by

Cognex Corporation. Cognex Corporation is not responsible for any errors that may be present in either this document or

the associated software.

Companies, names, and data used in examples herein are fictitious unless otherwise noted. No part of this document

may be reproduced or transmitted in any form or by any means, electronic or mechanical, for any purpose, nor

transferred to any other media or language without the written permission of Cognex Corporation.

Portions of the hardware and software provided by Cognex may be covered by one or more U.S. and foreign patents, as

well as pending U.S. and foreign patents listed on the Cognex web site at: http://www.cognex.com/patents.

The following are registered trademarks of Cognex Corporation:

Cognex, 2DMAX, Advantage, Alignplus, Assemblyplus, CheckitwithChecker, Checker, CognexVisionforIndustry,

CognexVSOC, CVL, DataMan, DisplayInspect, DVT, EasyBuilder, Hotbars, IDMax, In-Sight, LaserKiller, MVS-8000,

OmniView, PatFind, PatFlex, PatInspect, PatMax, PatQuick, SensorView, SmartView, SmartAdvisor, SmartLearn,

UltraLight, VisionSolutions, VisionPro, VisionView

The following are trademarks of Cognex Corporation:

The Cognex logo, 1DMax, 3D-Locate, 3DMax, BGAII, CheckPoint, CognexVSoC, CVC-1000, FFD, iLearn, In-Sight

(design insignia with cross-hairs), In-Sight2000, InspectEdge, Inspection Designer, MVS, NotchMax, OCRMax,

PatMaxRedLine, ProofRead, SmartSync, ProfilePlus, SmartDisplay, SmartSystem, SMD4, VisiFlex, Xpand

Other product and company trademarks identified herein are the trademarks of their respective owners.

Regulations/Conformity

Note: For the most up-to-date CE declaration and regulatory conformity information, please refer to the Cognex

online support site: http://www.cognex.com/Support.

Declaration of Conformity

Manufacturer Cognex Corporation

One Vision Drive

Natick, MA 01760 USA

In-Sight 7010/7010C/7020/7050: Regulatory Model 1AAA

In-Sight 7200/7200C/7210/7230: Regulatory Model 1AAA

In-Sight 7400/7400C/7410/7430: Regulatory Model 1AAA

In-Sight 7402/7402C/7412/7432: Regulatory Model 1AAA

FCC FCC Part 15, Class A

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two

conditions: (1) this device may not cause harmful interference; and (2) this device must accept any

interference received, including interference that may cause undesired operation. This equipment

generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance

with the instruction manual, may cause harmful interference to radio communications. Operation of this

equipment in a residential area is likely to cause harmful interference in which case the user will be

required to correct the interference at their own expense.

KCC In-Sight 7010/7010C/7020/7050: Regulatory Model 1AAA KCC-REM-CGX-1AAA

In-Sight 7200/7200C/7210/7230: Regulatory Model 1AAA KCC-REM-CGX-1AAA

In-Sight 7400/7400C/7410/7430: Regulatory Model 1AAA KCC-REM-CGX-1AAA

In-Sight 7402/7402C/7412/7432: Regulatory Model 1AAA KCC-REM-CGX-1AAA

NRTL TÜV SÜD AM SCC/NRTL OSHA Scheme for UL/CAN 60950-1. Regulatory Model 1AAA.

CB TÜV SÜD AM, IEC/EN 60950-1. CB report available upon request.

EU RoHS Compliant to the latest applicable Directive.

iii

China RoHS

Hazardous Substances 有害物质

Part Name

部件名称

Lead (Pb)

铅

Mercury (Hg)

汞

Cadmium

(Cd)

镉

Hexavalent

Chromium

(Cr (VI))

六价铬

Polybrominated

biphenyls (PBB)

多溴联苯

Polybrominated

diphenyl ethers (PBDE)

多溴二苯醚

Regulatory

Model 1AAA

X O O O O O

This table is prepared in accordance with the provisions of SJ/T 11364.

这个标签是根据SJ / T 11364 的规定准备的。

O: Indicates that said hazardous substance contained in all of the homogeneous materials for this part is below the

limit requirement of GB / T26572 - 2011.

表示本部件所有均质材料中含有的有害物质低于GB / T26572 - 2011 的限量要求。

X: Indicates that said hazardous substance contained in at least one of the homogeneous materials used for this part is

above the limit requirement of GB / T26572 - 2011.

表示用于本部件的至少一种均质材料中所含的危害物质超过GB / T26572 - 2011 的限制要求。

Precautions

Observe these precautions when installing the vision system to reduce the risk of injury or equipment damage:

lThe In-Sight vision system is intended to be supplied by a UL or NRTL listed power supply with a 24VDC output

rated for at least 2A continuous and a maximum short circuit current rating of less than 8A and a maximum power

rating of less than 100VA and marked Class 2 or Limited Power Source (LPS). Any other voltage creates a risk of

fire or shock and can damage the components. Applicable national and local wiring standards and rules must be

followed.

lAccording to IEC 62471, the white ring light is in Risk Group 1; it is not recommended to stare directly into the

illumination LEDs when the vision system is receiving power. According to IEC 62471, the blue ring light is in

Risk Group 2; CAUTION – Possibly hazardous optical radiation emitted from this product. Do not stare at

operating light. May be harmful to the eyes. The green ring light, the red ring light and the Infrared (IR) ring light

are Exempt Group products, therefore no precautions are required.

lDo not install In-Sight vision systems where they are directly exposed to environmental hazards such as

excessive heat, dust, moisture, humidity, impact, vibration, corrosive substances, flammable substances, or static

electricity.

lTo reduce the risk of damage or malfunction due to over-voltage, line noise, electrostatic discharge (ESD), power

surges, or other irregularities in the power supply, route all cables and wires away from high-voltage power

sources.

lDo not expose the image sensor to laser light; image sensors can be damaged by direct, or reflected, laser light.

If your application requires the use of laser light that may strike the image sensor, a lens filter at the

corresponding laser's wavelength is recommended. Contact your local integrator or application engineer for

suggestions.

lThe In-Sight vision system does not contain user-serviceable parts. Do not make electrical or mechanical

modifications to In-Sight vision system components. Unauthorized modifications may void your warranty.

lChanges or modifications not expressly approved by the party responsible for regulatory compliance could void

the user’s authority to operate the equipment.

lService loops should be included with all cable connections.

lCable shielding can be degraded or cables can be damaged or wear out more quickly if a service loop or bend

radius is tighter than 10X the cable diameter. The bend radius must be at least six inches from the connector.

lClass A Equipment (broadcasting and communication equipment for office work): Seller and user shall be

notified that this equipment is suitable for electromagnetic equipment for office work (Class A) and can be used

outside the home.

lThis device should be used in accordance with the instructions in this manual.

Table of Contents

Legal Notices i

Regulations/Conformity iii

China RoHS iv

Precautions v

Introduction 1

Support 1

Standard Components 1

Accessories 2

Cables 2

Installation 5

Connectors and Indicators 5

Install the Lens (C-Mount Lens Configuration) 7

Mount the Vision System 9

Working Distance and Field of View 10

Connect the Light Cable (Optional) 12

Connect the Ethernet Cable 12

Connect the Breakout Cable 13

Specifications 15

Vision System Specifications 15

I/O Specifications 17

Acquisition Trigger Input 17

General-Purpose Inputs 18

High-Speed Outputs 20

RS-232 Receive and Transmit 22

RS-232 Connector Configuration 22

Ethernet Cable Specifications 23

Light Cable Specifications 24

Breakout Cable Specifications 25

Vision System Dimensions 26

Appendix A - Cleaning/Maintenance 31

Clean the Vision System Housing 31

Clean the Vision System Image Sensor Window (C-Mount Lens Configuration) 31

Clean the Vision System Lens Cover 31

vii

viii

Altri manuali per In-Sight 7010

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Cognex Sistema di visione artificiale

Cognex

Cognex In-Sight EZ-700 Series Manuale utente

Cognex

Cognex In-Sight 3D-L4000 Series Manuale utente

Cognex

Cognex In-Sight 8000 Series Manuale utente

Cognex

Cognex In-Sight 5000 Series Istruzioni per l'installazione e il funzionamento

Cognex

Cognex In-Sight 2801 Manuale utente

Cognex

Cognex In-Sight 5100 Manuale utente

Cognex

Cognex In-Sight 9902L Manuale utente

Cognex

Cognex In-Sight 7000 Gen2 Series Manuale utente

Cognex

Cognex In-Sight 7000 Gen2 Series Manuale utente

Cognex

Cognex DataMan 360 Series Manuale utente

Cognex

Cognex In-Sight 7000 Series Manuale utente

Cognex

Cognex In-Sight Micro 1050 Manuale utente

Cognex

Cognex In-Sight D900 Series Manuale utente

Cognex

Cognex In-Sight D900 Series Manuale utente

Cognex

Cognex In-Sight 2800 Series Manuale utente

Cognex

Cognex In-Sight 2000 Manuale utente

Cognex

Cognex In-Sight 7000 Series Guida rapida

Cognex

Cognex In-Sight 9000 Series Manuale utente

Cognex

Cognex In-Sight 8000 Series Manuale utente

Cognex

Cognex DataMan 370 Series Manuale utente

Cognex

Cognex In-Sight 8405 Manuale utente

Cognex

Cognex 9000 SerieIn-Sights Manuale utente

Cognex

Cognex In-Sight 5110 Manuale utente

Cognex

Cognex In-Sight 8200 Manuale utente

Manuali Sistema di visione artificiale popolari di altre marche

Festo

Festo SBOC-M-R1B-H Manuale utente

Banner

Banner VE200G1B Manuale utente

SVS-Vistek

SVS-Vistek CoaxPress EoSens Creation 1.1CXP2 Manuale utente

Sony

Sony Vision Exchange PEQ-C100 Manuale utente

Datalogic

Datalogic MX-U81 Istruzioni per l'installazione

Spektrum

Spektrum SPMVR2520 Manuale utente

Huaray

Huaray Movidius Series Manuale utente

Daheng Imaging

Daheng Imaging MERCURY2 USB3 Manuale utente

SVS-Vistek

SVS-Vistek exo174 U3 Series Manuale utente

Teledyne

Teledyne e2v Eliixa+ Series Manuale utente

Photron

Photron FASTCAM Mini CX Series Manuale utente

National Instruments

National Instruments Vision CVS-1455 Manuale utente

Omron

Omron FH-L550 Manuale utente

iGen

iGen NV20/20 Manuale utente

JAI

JAI GO-5100MP-USB Manuale utente

Ark Vision Systems

Ark Vision Systems AVS-Monitor 7 FHD Manuale utente

Feniex

Feniex C-5500 Manuale utente

SVS-Vistek

SVS-Vistek CoaXPress fxo540 Manuale utente