Compex LinkPort ENET-B Manuale utente
Compex
LinkPort
PCMCIA Ethernet
Card
ENET-B
User’s Manual
Version 1.7C
i
Compex LinkPort
PCMCIA Ethernet Card
ENET-B
User’s Manual
Version 1.7C
Manual Number: M-0011-V1.7C
Manual Release Date: October 1999
Printed in the Republic of Singapore
ii
Disclaimer
Compex, Inc. provides this guide without warranty of any kind, either
expressed or implied, including but not limited to the implied warranties of
merchantability and fitness for a particular purpose. Compex, Inc. may make
improvements and/or changes to the product and/or specifications of the product
described in this guide, without prior notice.
Compex, Inc. will not be liable for any technical inaccuracies or typographical
errors found in this guide. Changes are periodically made to the information
contained herein and will be incorporated into later versions of the guide. The
information contained is subject to change without prior notice.
Trademark Information
Compex®,LinkPort®and ReadyLINK®are registered trademarks of Compex,
Inc. All brand and product names are trademarks or registered trademarks of
their respective owners.
Notice
Copyright ©1997 by Compex, Inc.. All rights reserved. Reproduction,
adaptation, or translation without prior permission of Compex, Inc. is
prohibited, except as allowed under the copyright laws.
Manual Revision by Leon Enriquez
Important Information
The latest updates and changes after the release of this manual can be found in
the RELEASE.TXT file in the latest Compex LinkPort release diskette.
iii
DECLARATION OF CONFORMITY
Manufacturer’s Name: Compex, Inc.
Manufacturer’s Address: 4051 E. La Palma, Unit A
Anaheim, CA 92807 U S A
Compex, Inc. declares that the product:
Product Name: Compex LinkPort,
PCMCIA Ethernet Card
Model Number: ENET-A
conforms to the following Product Standards:
Radiated Emission
Standards: EN55022B
FCC Part 15 Class B
Conducted Emission
Standards: EN60555PT2 conducted emission
EN55022B conducted emission
FCC Part 15 Class B
Immunity Standards: IEC 801-2
IEC 801-3
IEC 801-4
Therefore, this product is in conformity with the following
regional standards:
FCC Class B — following the provisions of FCC Part
15 directive.
CE Mark — following the provisions of the EC
directive.
Singapore, October 1999
_______________________
Dr Jackson Lam,
R & D Manager
European Contact:
ReadyLINK Networktechnology Gmbh, Technical Support,
Albert Einstein Straβe 42,
63322 Rödermark, Germany.
[FAX: +49 (60) 749-0668]
iv
FCC Notice
This device has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This device generates, uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this device does cause harmful
interference to radio or television reception, the user is encouraged to try
to correct the interference by one or more of the following measures:
p
p
p
p
Reorient or relocate the receiving antenna.
Increase the separation between the computer and receiver.
Connect the computer into an outlet on a circuit different
from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for
help.
Caution: Any changes or modifications not expressly approved by the
grantee of this device could void the user's authority to operate the
equipment.
FCC Compliance Statement
This device complies with Part 15 of the FCC Rules. Operation is subject
to the following two conditions:
(1)
(2)
This device may not cause harmful interference, and
This device must accept any interference received, including
interference that may cause undesired operation.
v
Contents
Chapter 1: Introduction 1-1
Chapter 2: Installing the Adapter 2-1
Chapter 3: Software Installation 3-1
Appendix A: Technical Information A-1
Appendix B: Technical Support B-1
vi
NOTES
Compex LinkPort PCMCIA Ethernet Card
Chapter 1
Introduction
The
Compex LinkPort PCMCIA
(Personal Computer
Memory Card International Association) Ethernet card
[ENET-B] is a credit card sized network adapter that
can be used for PCMCIA compliant personal computers.
The Compex LinkPort PCMCIA Ethernet card plugs
into a Type II PCMCIA slot, providing a 16-bit bus
interface. The card is switchless, software configurable,
and provides full support for the PCMCIA Card
Information Structure (CIS).
The card is supplied with a media coupler that provides
a BNC coaxial 10Base-2 connector, and a UTP
(Unshielded Twisted-Pair) 10Base-T connector.
Also included is an intelligent Enabler program that
automatically detects your PC’s controller type and
recognises previously installed card and socket services.
1-2Chapter 1: Introduction
Features
≥≥ Conforms to IEEE 802.3, PCMCIA Release 2.1,
JEIDA 4.1 Standard.
≥≥ Fits into Type II PCMCIA slot.
≥≥ Provides 68-pin connector for attachment to PC
and 15-pin flat connector for attachment to media
coupler.
≥≥ Media coupler incorporates RJ-45 10Base-T UTP
connector and BNC 10Base-2 coaxial connector.
≥≥ Switchless design; hardware settings are software
configurable.
≥≥ Low power consumption.
≥≥ Extensive software driver support which includes
drivers for Novell NetWare; NDIS driver for
Microsoft LAN Manager; drivers for Microsoft
Windows for Workgroups, Windows 95,
Windows NT v3.51, Windows NT v4.0; Packet
Driver applications; LANtastic v6.0; and IBM
OS/2 Warp.
(Refer to the driver diskette for the latest updated
list.)
Chapter 1: Introduction 1-3
Hardware Description
≥≥ PCMCIA card
The Compex LinkPort PCMCIA Ethernet card’s main
PCB board is encased in a stainless compact frame. It has
a 68-pin connector that fits into a PCMCIA socket,. and a
15-pin flat connector that connects to the media coupler.
≥≥ Media Coupler
Media coupler incorporates RJ-45 10Base-T UTP
connector and BNC 10Base-2 coaxial connector.
≥≥ LED Indicators
↵
ACT LED
(Colour: orange) Function: Monitors
signals transmitted to and received from the
network.
The orange LED, labelled
ACT
, lights up to
indicate that the PCMCIA Card is transmitting
signals to and/or receiving signals from the
network. This LED is normally OFF. It will flash
when the card transmits signals to the network.
The speed at which the LED flashes increases with
the level of network traffic.
↵LINK LED (Colour:green) Function: Monitors
link status of twisted-pair connection. The
PCMCIA Card supports the link integrity test
function. This function is automatically enabled
when the card is configured for RJ-45 UTP cabling.
The green LED, labelled
LINK
, lights up to
indicate that a valid 10Base-T link has been
established. It is ON under normal operating
conditions. If the LED is OFF, check the RJ-45
port’s cable connection.
Note: The LINK LED only monitors the 10Base-T
(R J-45) connection. To check the condition of the
BNC link, run the diagnostics program.
Indice
Altri manuali Compex Scheda di rete
Manuali Scheda di rete popolari di altre marche
Buffalo
Buffalo AirStation WLI-PCM-L11GP Manuale utente
National Instruments
National Instruments NI 9234 Manuale utente
Hama
Hama 49276 Manuale utente
Linksys
Linksys WCF54G - Wireless-G Compact Flash Card Manuale operativo
Compaq
Compaq Wireless LAN 100 Manuale utente
Bose
Bose PowerMatch Dante Manuale utente