Concept Pro CBP4304 Manuale utente

CBP4304

CBP4324

CVP9304

Colour Dome Camera

USER MANUAL

1. This installation should be made by a qualified service person and should abide to all local

codes.

2. Avoid installation on a surface subjected to frequent vibration or shocks.

3. Do not operate the camera beyond its temperature range or power source ratings.

4. Should any damage or suspected damage occur, shutdown the power source, unplug and

contact your service provider.

5. Do not install the camera under unstable lighting conditions. Severe lighting change or

flicker can cause the camera to work improperly.

6. Never use the camera close to a gas or oil leak.

7. Do not disassemble the camera.

8. Never keep the camera face to strong light directly, this can damage the CCD.

9. Ensure all removable covers are replaced to protect the inner components.

10. Do not install near devices which emit a strong electro-magnetic field.

11. Use a dry or damp cloth only for cleaning.

12. Internal dome only - Do not drop the camera or subject the unit to physical shocks.

PLEASE FOLLOW THE ABOVE CAUTIONS – FAILURE TO DO SO MAY

INVALIDATE THE WARRANTY OR CAUSE SERIOUS INJURY.

Remark: Changes or modifications not expressly approved by the manufacturer can

cause the camera to be damaged and become inoperable. This may invalidate the

user warranty.

CAUTION

1. This installation should be made by a qualified service person and should abide to all local

codes.

2. Avoid installation on a surface subjected to frequent vibration or shocks.

3. Do not operate the camera beyond its temperature range or power source ratings.

4. Should any damage or suspected damage occur, shutdown the power source, unplug and

contact your service provider.

5. Do not install the camera under unstable lighting conditions. Severe lighting change or

flicker can cause the camera to work improperly.

6. Never use the camera close to a gas or oil leak.

7. Do not disassemble the camera.

8. Never keep the camera face to strong light directly, this can damage the CCD.

9. Ensure all removable covers are replaced to protect the inner components.

10. Do not install near devices which emit a strong electro-magnetic field.

11. Use a dry or damp cloth only for cleaning.

12. Internal dome only - Do not drop the camera or subject the unit to physical shocks.

PLEASE FOLLOW THE ABOVE CAUTIONS – FAILURE TO DO SO MAY

INVALIDATE THE WARRANTY OR CAUSE SERIOUS INJURY.

Important: Ensure all cautionary procedures are

observed during installation.

It is recommended the camera is tested during the most

demanding environmental conditions such as low light

or bright sunlight to ensure continuity of effective CCTV

monitoring.

Using the supplied fitting screws, securely attach the

camera to the drilled surface

Adjust the tri-axis gimbal zoom/focus to give the

required image of the area to be monitored.

Replace the dome cover by pushing firmly in place

onto the base

Carefully clean the dome surface with a soft lint

free cloth

Remove the camera unit carefully from the box

reserving the accessory contents in a safe place

Use the supplied mounting template to mark the

space for drilling

Remove the dome cover using a suitable coin or

screwdriver

FIXING TO A WALL

CBP4304/4324

Ceiling

PACKING CONTENTS

CBP4304 / 4324

Wall Plugs

Mounting Template

Fitting Screws

INTERNAL DOME INSTALLATION

Important: Ensure all cautionary procedures are

observed during installation.

It is recommended the camera is tested during the most

demanding environmental conditions such as low light

or bright sunlight to ensure continuity of effective CCTV

monitoring.

Attach the weatherproof sealing pad to the base of

the dome with the sticky side against the camera

Using the supplied fitting screws, securely attach the

camera to the drilled surface

Please note: To ensure correct weatherproof you

must use the enclosed fitting screws and

weatherproof washers

Adjust the tri-axis gimbal zoom/focus to give the

required image of the area to be monitored.

Replace the dome cover and tighten the dome cover

screws using the supplied dome cover screw driver

Carefully clean the dome surface with a soft lint

free cloth

Remove the camera unit carefully from the box

reserving the accessory contents in a safe place

Use the supplied mounting template to mark the

space for drilling

Remove the dome cover using the supplied dome

cover screwdriver

FIXING TO A WALL

CVP9304

PACKING CONTENTS

Wall Plugs

Conduet hole cover

opener

Mounting Template

Fitting Screws

Dome cover

screwdriver

Weatherproof

sealing washers

Weatherproof

sealing pad

Ceiling

CVP9304

VANDAL RESISTANT DOME INSTALLATION

Using the supplied fitting screws, securely attach the

camera to the drilled surface

Adjust the tri-axis gimbal zoom/focus to give the

required image of the area to be monitored.

Replace the dome cover by pushing firmly in place

onto the base

Carefully clean the dome surface with a soft lint

free cloth

Remove the camera unit carefully from the box

reserving the accessory contents in a safe place

Use the supplied mounting template to mark the

space for drilling

Remove the dome cover using a suitable coin or

screwdriver

Attach the weatherproof sealing pad to the base of

the dome with the sticky side against the camera

Using the supplied fitting screws, securely attach the

camera to the drilled surface

Please note: To ensure correct weatherproof you

must use the enclosed fitting screws and

weatherproof washers

Adjust the tri-axis gimbal zoom/focus to give the

required image of the area to be monitored.

Replace the dome cover and tighten the dome cover

screws using the supplied dome cover screw driver

Carefully clean the dome surface with a soft lint

free cloth

Remove the camera unit carefully from the box

reserving the accessory contents in a safe place

Use the supplied mounting template to mark the

space for drilling

Remove the dome cover using the supplied dome

cover screwdriver

CONNECTION

Connect the video out port to your video cable

running to the monitor / recorder

Check the power supply is of the correct level

and connect your power supply into the power

port on the Camera.

View the picture on a monitoring device to

check the power and video connection is

working properly.

PSU

Troubleshooting

Ensure all power and cable connections are correct with the Camera and DVR.

If all power and cable connections are correct and the camera picture can not be

produced then contact your supplier for technical support.

Tri-Axis Gimbal

Example shows vandal resistant dome casing

360º

90º

360º

94.64

51.0135.48

148.39

46.00

82.50

105.00

86.00

94.64

53.18

15.00

147.97

106.10

CVP9304CBP4304 / 4324

SPECIFICATION

Design and specification are subject to change without notice.

MODEL

Image Sensor

Effective Pixels

Horizontal Resolution

Min. Illumination

Lens

Day & Night

S/N Ratio

White Balance

AGC

BLC

Sync System

BNC Video Output

Input Voltage

Power Consumption

Operating Temperature

Dimension

Weight

CBP4304 CBP4324

Sony Super HAD

PAL: 500(H) x 582(V) ; NTSC: 510(H) x 494(V)

420TVL

0.3Lux/F1.2

Colour Only

more than 48dB

AUTO

Internal

CVBS 1.0Vp-p / 75Ω

12v DC

120mA

-10ºC~ +50ºC RH90% MAX

Fixed Lens f=4mm Auto Iris Vari-focal

lens F=4-9mm

148x106 (DxH)

650g

SPECIFICATION

Design and specification are subject to change without notice.

MODEL

Image Sensor

Effective Pixels

Horizontal Resolution

Min. Illumination

Lens

Day & Night

S/N Ratio

White Balance

AGC

BLC

Sync System

BNC Video Output

Input Voltage

Power Consumption

Operating Temperature

Dimension

Weight

CVP9304

Sony Super HAD

PAL: 500(H) x 582(V) ; NTSC: 510(H) x 494(V)

420TVL

0.3Lux/F1.2

Fixed Lens f=4mm

Colour Only

more than 48dB

AUTO

Internal

CVBS 1.0Vp-p / 75Ω

12v DC

120mA

-10ºC~ +50ºC RH90% MAX

148.35x105 (DxH)

950g

CONCEPT PRO DOME CAMERA RANGE

INTERNAL DOME CAMERAS

CBP3212

CBP5112

CBP5212

CBP4304

CBP5314

CBP4324

CBP6324

CBP6324-B

CBP6324DN

CBP6324WDR

VANDAL RESISTANT DOME CAMERAS

CVP9304

CVP9314

CVP9324

CVP9324DN

CVP9324LL

CVP9324WDR

INFRARED DOME RANGE

CBP6314DNIR

CBP6324DNIR

CVP9314DNIR

CVP9324DNIR

VANDAL RESISTANT WALL BRACKET

CVP-BRK

480TVL, 0.3 Lux, 3.6mm Lens. 90(ø)x62mm

420TVL, 0.3 Lux, 3.6mm Lens, 128(ø)x93mm

480TVL, 0.3 Lux, 3.6mm Lens, 128(ø)x93mm

420TVL, 0.3 Lux, 4mm Lens, 148(ø)x106mm

650TVL, 0.03Lux, 4mm Lens, 148(ø)x106mm

420TVL, 0.3 Lux, 4-9mm Lens,148(ø)x106mm

650TVL, 0.03Lux 2.8-10mm Lens, 148(ø)x106mm

650TVL, 0.03 Lux, 2.8-10mm Lens, 148(ø)x106mm, Black casing

650TVL, 0.03 Lux, 2.8-10mm, Day Night, 148(ø)x106mm

690TVL, 0.01 Lux, 2.8-10mm Lens, Day Night, Wide Dynamic

Range,148(ø)x106mm

420TVL, 0.3 Lux, 4mm Lens, 148.35(ø)x105mm

650TVL, 0.03Lux, 4mm Lens, 148.35(ø)x105mm

650TVL, 0.03Lux 2.8-10mm Lens, 148.35(ø)x105mm

650TVL, 0.03 Lux, 2.8-10mm, Day Night, 148.35(ø)x105mm

600TVL, 0.0002 Lux (DSS/Sens Up on) 2.8-10mm Lens,

148.35(ø)x105mm

690TVL, 0.01 Lux, 2.8-10mm Lens, Day Night, Wide Dynamic Range,

148.35(ø)x105mm

600TVL, 4mm Lens, IR LED, 148(ø)x106mm

650TVL, 2.8-10mm Lens, IR LED, ICR, 148(ø)x106mm

600TVL, 4mm Lens, IR LED, 148.35(ø)x105mm

650TVL, 2.8-10mm Lens, IR LED, ICR, 148.35(ø)x105mm

Wall bracket for use with all CVP dome cameras

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Concept Pro Telecamera di sicurezza

Concept Pro

Concept Pro CVP9328DNIR-IP4M Manuale utente

Concept Pro

Concept Pro AIR8010-AHD-Z Manuale utente

Concept Pro

Concept Pro CVP9324-AHD Manuale utente

Concept Pro

Concept Pro VHSDIR-812EXT-IP3M Manuale utente

Concept Pro

Concept Pro CP-HSD10-IP Manuale utente

Concept Pro

Concept Pro CBP6314DNIR Manuale utente

Concept Pro

Concept Pro CVP9328DNIR-IP2M-Z Manuale utente

Concept Pro

Concept Pro AIR2024-IP2M/2.8 Manuale utente

Concept Pro

Concept Pro VCP7238-AHD Manuale utente

Concept Pro

Concept Pro CVP5325DNIR-IP2M/2.8 Manuale utente

Concept Pro

Concept Pro VCP553 Manuale utente

Concept Pro

Concept Pro CVP9324DN-IP Manuale utente

Concept Pro

Concept Pro VHSDIR-670EXT-IP Manuale utente

Concept Pro

Concept Pro CPL-MVIR-IP2M/2.8 Manuale utente

Concept Pro

Concept Pro VCP7236 Manuale utente

Concept Pro

Concept Pro CVP5325DNIR-AHD2M/2.8 Manuale utente

Concept Pro

Concept Pro VHSDIR-680EXT-IP Manuale utente

Concept Pro

Concept Pro AHD Series Manuale utente

Concept Pro

Concept Pro VHSD-810EXT Manuale utente

Concept Pro

Concept Pro AIR3526-AHD2M Manuale utente

Concept Pro

Concept Pro CBP360-HD Manuale utente

Concept Pro

Concept Pro AIR8012-IP3M-Z Manuale utente

Concept Pro

Concept Pro AIR3526-IP2M Manuale utente

Concept Pro

Concept Pro CVP9324DN-IP4M Manuale utente

Manuali Telecamera di sicurezza popolari di altre marche

Okina USA

Okina USA SIR36-870VF650LP Manuale utente

Divio

Divio NDR155PA Manuale utente

Canon

Canon VB-C500D Manuale utente

Easy Access

Easy Access EasyGuard Manuale utente

Vivotek

Vivotek FD9389-EHV-v2 Manuale utente

TUYA

TUYA COSMO W2 Manuale utente

Eusso

Eusso UNC7500-IR Guida all'installazione

urmet domus

urmet domus 1096/204 Manuale utente

VC VC20 series Manuale utente

Axis

Axis Q1614 Manuale utente

ieGeek

ieGeek DD201 Manuale utente

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Manuale utente

Vicon

Vicon V662-D-1 Istruzioni operative

Grundig

Grundig GCH-K0274P Manuale utente

Lorex

Lorex VANTAGE LBC7032 Manuale utente

4xem

4xem WPT Manuale utente

Samsung

Samsung SCV-3082 Manuale utente

Vitek

Vitek VTC-C544 Manuale utente