ConMed 3DHD Manuale utente
INSTALLATION GUIDE
11/13/12
3DHD VISION SYSTEM
@2012 by ConMed Corporation- All rights reserved. MCM2012221
This publication is protected by copyright. Copying, disclosure to others, or sue of this publication is prohibited without
express written consent of ConMed Corporation. ConMed Corporation reserves the right to make changes show herein
without notice or obligation. Contact ConMed Corporation or your representative for the latest information.
MARKETING COMMUNICATIONS
INSTALLATION GUIDE
11/9/12
3DHD VISION SYSTEM
2
MARKETING COMMUNICATIONS
This installation guide is for use by ConMed Distributors to ensure proper set up of the
ConMed 3DHD Vision System. For more detailed information and for trouble shooting by
product please refer to the product User Manuals which can be found with each of the
individual 3DHD Vision System components.
Tools Required:
Utility Knife
Phillips Screw Driver
Country specific Power Cord for Cart (outside the US, Canada, Mexico, and
Puerto Rico)
6MM Hex Bit Socket Wrench
Alignment Target Part #T05713-001
Tools Supplied:
4MM Allen Wrench
Inspect all shipping packages for any signs of mishandling or damage! In the event of
damage please contact Customer Service:
CART:
To unpack cart cut strapping, remove top cover and slide side packaging up and
over cart.
Lift cart out of packaging base and place on floor.
Inspect for any damages, including cosmetic damages.
Phillips Screw Driver is a registered trademark of Phillips Screw Company
Allen in a registered trademark of Allen Manufacturing Company
Note: If any discrepancies cannot be resolved please report immediately to Viking
Systems Technical Support!
Note: Cart may or may not be shipped on its side, if so, cut strapping to release
cart from pallet and tip cart box to the upright position.
Note: Carts sent outside of the U.S. with the exclusion of Canada, Mexico and
Puerto Rico are shipped without an AC Power Cord. It is the responsibility of the
installer to provide the proper AC Cord.
INSTALLATION GUIDE
11/9/12
3DHD VISION SYSTEM
3
MARKETING COMMUNICATIONS
WARNING: Do not connect AC mains of cart to power.
AC CORD INSTALLATION FOR CART
Figure 1 Figure 2 Figure 3
Tip the Video Cart onto its front end, as shown in Figure 1.
a. Un-package the Video Cart and carefully tip the Video Cart onto its front
end.
Insert the Hospital Grade Power Cord into the Base of the Video Cart as shown in
Figure 2.
a. Insert the Hospital Grade power under the Base of the Video Cart and feed
the plug end of the power cord through the space under the Power Strip and
out the front of the Video Cart.
b. Plug the Hospital Grade Power Cord into the outlet under the green pilot
light of Power Strip.
Secure the Hospital Grade Power cord using the clip provided with the Video Cart,
as shown in Figure 3.
a. Remove the Cap Screw and Washer holding the power cord clip using a
6mm hex bit, and place the loose clip onto the Hospital Grade Power Cord.
b. Secure the clip and power cord back onto the Video Cart using the existing
Cap Screw and Washer.
MOUNTING INSTRUCTIONS FOR VIDEO DISPLAY: (SONY)
Open 8272-14 Sony* 3DHD video display monitor box and remove power
supply
Inspect for any damage including cosmetic damages.
Attach monitor Sony* video display AC power supply to mounting bracket
underneath middle shelf of Cart. (Sony* monitor only)
Sony is a registered trademark of Sony Corporation of America.
INSTALLATION GUIDE
11/9/12
3DHD VISION SYSTEM
4
MARKETING COMMUNICATIONS
Figure 4 Figure 5 Figure 6
Attach the Mounting Bracket to the Sony Monitor Power Supply as shown in Figure 4.
a. Remove backing from the double sided tape on the Mounting Bracket.
b. Position the Mounting Bracket so the slotted hole is to the left and the double
sided tape is facing up.
c. Position the Power Supply feet facing up with the cord to the Sony* Monitor
facing you.
d. Attach the Mounting Bracket to the Power Supply approximately on center and
press firmly together.
Place the Mounting Bracket & Power Supply under the middle shelf of the Video Cart
as shown in Figure 5.
a. Standing in front of the Video Cart, place the right side of the Mounting Bracket
& Power Supply under the right side of the 2nd shelf with the cord to the Sony*
Monitor facing you.
b. Fold the Mounting Bracket & Power Supply up so it is flat up against the bottom
of the Video Cart shelf. The Mounting Bracket & Power Supply should be
loosely in position, Do no force into place.
Secure the Mounting Bracket & Power Supply to the middle shelf of the Video Cart as
shown in Figure 6.
a. Slide the Mounting Bracket & Power Supply forward until the slotted hole in the
Mounting Bracket is aligned with the mounting hole in the shelf of the Video
Cart.
b. Insert the mounting hardware included with the Mounting Bracket and slide the
Mounting Bracket & Power Supply to the front of the Video Cart until it is snug,
and secure the mounting hardware hand tight.
Sony is a registered trademark of the Sony Corporation of America.
INSTALLATION GUIDE
11/9/12
3DHD VISION SYSTEM
5
MARKETING COMMUNICATIONS
Run 4 prong power cable for monitor video display, through cart channel as shown
in Figures 7-10:
Figure 7 Figure 8 Figure 9 Figure 10
Attach one of the 1 m IEC 320 power cords to power supply as shown in
Figure 11.
Figure 11
Open 3DHD controller packaging and remove HD-SDI cables. Figure 12
indicates Left and Right Cables.
Left = All Black Cable Right = Black cable with white
ring
Figure 12
INSTALLATION GUIDE
11/9/12
3DHD VISION SYSTEM
6
MARKETING COMMUNICATIONS
Loosen
Run the HD-SDI video cables through cart extension channel as shown in
Figures 13 and 14:
Figure 13 Figure 14
Right angle end goes to the CCU (middle shelf).
Reinstall plastic cart column covers.
Unpack Sony 3D monitor.
Inspect for any damages including cosmetic damages.
Vesa Mounting pattern on back of the Sony* monitor, once unpacked should
look like picture shown in Figure 15:
Figure 15
Where Shown:
Loosen the top 2 middle screws
Remove the bottom 2 screws where shown in in Figure 16.
Figure 16
Sony is a registered trademark of Sony Corporation of America.
Vesa Mounting is a trademark of Video Electronic Standards Association.
Remove
INSTALLATION GUIDE
11/9/12
3DHD VISION SYSTEM
7
MARKETING COMMUNICATIONS
Attach monitor video display to cart’s Vesa mounting bracket.
Attach the remaining two bottom screws to remaining holes in the Vesa*
mounting bracket, tighten all screws, Vesa* bracket should like pictures shown
in Figures 17 and 18:
Figure 17 Figure 18
Connect power cord to Sony monitor video display as shown in Figure 19:
Figure 19
Connect left (black) HD-SDI video cable to Sony* 3G Card input 1
Connect right (white) HD-SDI video cable to Sony* 3G Card input2
MONITOR AT THIS POINT WILL LOOK LIKE FOLLOWING PICTURE IN FIGURE 20
Figure 20
MOUNTING INSTRUCTIONS FOR VIDEO DISPLAY: (PANASONIC)
Unpack 8272-19 Panasonic* 3D monitor video display.
Inspect for any damages including cosmetic damages.
Vesa is a trademark of Video Electronic Standards Association.
Sony is a registered trademark of Sony Corporation of America.
Panasonic is a registered trademark of Panasonic Corporation Japan.
INSTALLATION GUIDE
11/9/12
3DHD VISION SYSTEM
8
MARKETING COMMUNICATIONS
Remove existing vesa mounting plate from the cart and install 200/200 Vesa
Plate as shown below in Figures 21 and 22.
Figure 21 Figure 22
200/200 VESA MOUNTING* PLATE INSTALLATION
1. Remove the four (4) existing screws from the front of the existing tilt / swivel VESA
mount* plate, and remove the existing VESA mounting* plate. See Figure 21.
2. Using the four (4) existing screws, install the 200/200 VESA mounting* plate to the
existing mounting holes provided on the cart. See Figure 22.
Once the 200/200 Vesa Plate* as been installed, place Panasonic monitor video
display on bracket as shown in Figures 23 and 24.
Figure 23 Figure 24
Vesa Mounting is a trademark of Video Electronic Standards Association.
Panasconic is a registered trademark of Panasonic Corporation Japan.
INSTALLATION GUIDE
11/9/12
3DHD VISION SYSTEM
9
MARKETING COMMUNICATIONS
Connect power cord for Panasonic Monitor (There are 3 power cords on the
middle shelf, ensure you use the longest cord (1 1/2MM) ). Ensure the metal clip
on the monitor is engaged to secure the power cord. See Figure 26.
Connect left (black) HD-SDI video cable to the SDI-1 input as shown in Figure 25.
Connect right (white) HD-SDI video cable to the SDI-2 input as shown in Figure 25.
Figure 25
THE MONITOR AT THIS POINT WILL LOOK LIKE THE FOLLOWING PICTURE IN FIGURE 26
Figure 26
3DHD CONTROLLER:
Unpack the 8170-6 3DHD controller.
Inspect for any damages, including cosmetic damages.
Place the controller on the middle shelf as shown below.
Connect video cables to proper left (black) and right ( white banded) HD-SDI
outputs on controller.
Attach power cord to controller.
Place controller feet in the shelves detents to stabilize unit as shown in
Figure 27.
Panasonic is a registered trademark of Panasonic Corporation Japan.
Engage Clip
INSTALLATION GUIDE
11/9/12
3DHD VISION SYSTEM
10
MARKETING COMMUNICATIONS
Figure 27
3DHD LIGHT SOURCE:
Unpack the 8050-2 3DHD light source. Inspect for any damage, including
cosmetic damages.
Place the light source on top of the 3DHD controller (position feet in detents on
controller cover). As shown in Figure 28.
Figure 28
Attach power cord to light source.
FINISHED CART ASSEMBLY WILL LOOK LIKE FOLLOWING PICTURES IN
FIGURES 29 and 30
Figures 29 Figure 30
Indice
