Contemporary Controls MOD HUB Series Manuale utente
MOD HUB series
A Line of Modular Active Hubs for ARCNET
®
Local Area Networks
Expansion Modules
Installation Instructions
#TD471100-0IJ
Trademarks
Contemporary Controls, ARC Control, ARC DETECT, BASautomation,
and EXTEND-A-BUS are trademarks or registered trademarks of
Contemporary Control Systems, Inc. ARCNET is a registered
trademark of Datapoint Corporation. Other product names may be
trademarks or registered trademarks of their respective companies.
TD471100-0IJRevised MAR 2011
Copyright
© Copyright 2011, by Contemporary Control Systems, Inc. All
rights reserved. No part of this publication may be reproduced,
transmitted, transcribed, stored in a retrieval system, or translated
into any language or computer language, in any form or by any
means, electronic, mechanical, magnetic, optical, chemical, manual,
or otherwise, without the prior written permission of:
Contemporary Control Systems, Inc.
2431 Curtiss Street
Downers Grove, Illinois 60515 USA
Tel: +1-630-963-7070
Fax: +1-630-963-0109
E-mail: [email protected]
WWW: http://www.ccontrols.com
Contemporary Controls Ltd
14 Bow Court
Sir William Lyons Road
Coventry CV4 7EZ UK
Tel: +44 (0)24 7641 3786
Fax: +44 (0)24 7641 3923
E-mail: [email protected]
Disclaimer
Contemporary Control Systems, Inc. reserves the right to make
changes in the specifications of the product described within this
manual at any time without notice and without obligation of
Contemporary Control Systems, Inc. to notify any person of such
revision or change.
TD471100-0IJ
2
INTRODUCTION
This document provides instructions for installing and removing
expansion modules to be used in the MOD HUB series of
modular ARCNET active hubs. More detailed information
regarding the MOD HUB Series can be obtained by referring to
Contemporary Controls’ MOD HUB Series User Manual.
CABLING CONSIDERATIONS
The MOD HUB Series is a line of modular active hubs for
ARCNET local area networks. These hubs support several
cabling types including coaxial, twisted-pair and glass fiber
optics.
As far as topology is concerned, each MOD HUB expansion
module is designed for use in star or distributed star
configurations. Expansion modules can be used to extend the
length of coaxial and twisted-pair bus segments by connecting
the expansion module at the end of bus segments.
The cabling types supported by the MOD HUB Series are listed
on the following page with their corresponding model numbers.
TD471100-0IJ
3
Model Number Description
EXP-CXS 4-port coaxial star expansion module
EXP-CXS/FG3-ST Coax/1300 nm fiber expansion module
EXP-CXS/FOG-SMA 2-port coax/fiber SMA expansion
module
EXP-CXS/FOG-ST 2-port coax/fiber ST expansion module
EXP-CXS/485 2-port coax/485 expansion module
EXP-CXS/485X 2-port coax/485X expansion module
EXP-FOG-SMA 4-port fiber SMA expansion module
EXP-FOG-ST 4-port fiber ST expansion module
EXP-TPS 4-port twisted-pair expansion module
EXP-TPS/CXS 2-port twisted-pair/coax expansion
module
EXP-TPS/FOG-SMA 2-port twisted-pair/fiber SMA expansion
module
EXP-TPS/FOG-ST 2-port twisted-pair/fiber ST expansion
module
EXP-485 4-port DC EIA-485 expansion module
EXP-485/FOG-SMA 2-port 485/fiber SMA expansion module
EXP-485/FOG-ST 2-port 485/fiber ST expansion module
EXP-485X 4-port AC EIA-485 expansion module
EXP-485X/FOG-SMA 2-port 485X/fiber SMA expansion
module
EXP-485X/FOG-ST 2-port 485X/fiber ST expansion module
TD471100-0IJ
4
REMOVING MODULES FROM THE MOD HUB
Before removing the modules from the MOD HUB, turn the unit off by
depressing the power switch located on the front panel of the MOD HUB.
Unplug the power cord from the wall outlet. Disconnect the cables from
the connectors on the module that is beingremoved.
Dislodging Modules From The MOD HUB
Loosen the module from the MOD HUB unit by unscrewing both of the
captive screws with your fingers. The captive screws are located on each
end of the module. Loosen the captive screws until they are unthreaded to
the point where they hang freely fromthemodule.
With your fingers, grasp each of the module's captive screws and pull the
module out of the MOD HUB unit until it is free from the unit. (If you are
removing a blank panel, simply unscrew thetwo fasteners.)
INSTALLING MODULES INTO THE MOD HUB
Before installing modules into the MOD HUB, turn the unit off by
depressing the power switch located on the front panel of the MOD HUB.
Unplug the power cord from the wall outlet.
Loading Modules into the MOD HUB
Remove any blank panels or modules being replaced from the MOD HUB.
Unpackage the module to be installed, taking care not to harm the module.
Grasp the module by the faceplate (with its circuitry facing left) and gently
place the module into the empty slot on the MOD HUB. Push the module
into the MOD HUB (some force may be needed to seat the module into
position) until the module's face plate is seated against the unit.
TD471100-0IJ
5
Tighten the captive screws on the module with your fingers and fasten
them inthe locking position. Attach the cables running from each device
in the ARCNET LAN to the appropriate module connectors on the newly-
installed expansion module. Refer to the MOD HUB Series User Manual,
Chapter 2, to test the module for proper working operation.
TD471100-0IJ
6
NEED MORE HELP INSTALLING THIS PRODUCT?
More information can be found on our web site at www.ccontrols.com. Browse
the Technical Support section of our site for a look at our on-line technical
manuals, downloadable software drivers and utility programs that can test
the product. When contacting us, just ask for technical support.
Warranty
Returning Products for Repair
Return the product to the location from which it was purchased by following
the instructions at the URL below:
Contemporary Controls (CC) warrants its new product to the original purch-
aser for two years from the product shipping date. Product returned to CC
for repair is warranted for one year from the date that the repaired product is
shipped back to the purchaser or for the remainder of the original warranty
period, whichever is longer.
If a CC product fails to operate in compliance with its specification during the
warranty period, CC will, at its option, repair or replace the product at no
charge. The customer is, however, responsible for shipping the product; CC
assumes no responsibility for the product until it is received.
CC’s limited warranty covers products only as delivered and does not cover
repair of products that have been damaged by abuse, accident, disaster, mis-
use, or incorrect installation. User modification may void the warranty if the
product is damaged by the modification, in which case this warranty does not
cover repair or replacement.
This warranty in no way warrants suitability of the product for any specific
application. IN NO EVENT WILL CC BE LIABLE FOR ANY DAMAGES
INCLUDING LOST PROFITS, LOST SAVINGS, OR OTHER INCIDENTAL
OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR
INABILITY TO USE THE PRODUCT EVEN IF CC HAS BEEN ADVISED
OF THE POSSIBILITY OF SUCH DAMAGES, OR FOR ANY CLAIM BY
ANY PARTY OTHER THAN THE PURCHASER.
THE ABOVE WARRANTY IS IN LIEU OF ANY AND ALL OTHER
WARRANTIES, EXPRESSED OR IMPLIED OR STATUTORY, INCLUD-
ING THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR
PARTICULAR PURPOSE OR USE, TITLE AND NONINFRINGEMENT.
www.ccontrols.com/rma.htm
DECLARATION OF CONFORMITY
Additional compliance documentation can be found on our website.
www.ccontrols.com
Questo manuale è adatto per i seguenti modelli
18
Indice
Altri manuali Contemporary Controls Unità di controllo
Manuali Unità di controllo popolari di altre marche
Festo
Festo Compact Performance CP-FB6-E Manuale elenco delle parti
Elo TouchSystems
Elo TouchSystems DMS-SA19P-EXTME Manuale utente
JS Automation
JS Automation MPC3034A Manuale utente
JAUDT
JAUDT SW GII 6406 Series Guida rapida
Spektrum
Spektrum Air Module System Manuale utente
BOC Edwards
BOC Edwards Q Series Manuale utente
