Covita bedfont Micro+ basic Smokerlyzer Manuale utente
www.covita.net | 800-707-5751
Copyright 2018 coVita LLC All Rights Reserve v042618
Micro+™basic, baby, & pro
Smokerlyzer®
Calibration Gui e
Firmware ≤ V2.31
A. Calibraon Tips
Figure A
Figure B
1. coVita calibration instructional videos can be found
under the support section of www.covita.net .
2. You must calibrate every 6 months to correct for
sensor drift using 20 ppm Carbon Monoxi e (CO)
calibration gas. On occasion your Micro+™ may
prompt you for an intermittent calibration.
3. Your Micro+™ has built in calibration reminders to
prompt you to calibrate every 6 months.
4. Be sure to identify your flow meter-regulator for
correct instructions.
5. emove flow meter-regulator from can for proper
storage and replace dust cap. (You may hear a pop
and this is normal.)
6. Ensure that the cali-adaptor tubing has no kinks
while the gas is flowing.
7. Be sure you are using the compatible cali-adaptor
tubing and D-piece to avoid issues with calibrating.
8. Be sure you are inserting the D-piece into the monitor
correctly. The circle opening must be facing you.
(Figure A & B)
9. Never block the air/vent hole on the Micro+™ with
labels etc.
B. Required Parts
A. 20 ppm Carbon Monoxi e (CO) Calibration
Can
B. Fixed Flow 1 lpm meter-regulator
C. Cali-adaptor Tubing
D. D-Piece
E. Micro+™ Smokerlyzer®
C. Calibraon Kit Set Up
1. emove white or black dust cap from can of gas
2. Ensure the control valve on the flow meter-regulator
is in the off position.
3. Screw the regulator-flow meter onto the gas can
(some slight pressure may be required). This can be
done by screwing the gas can into the valve.
4. Attach the small end of the tubing onto the regulator-
flow meter.
5. Insert the larger end of the cali-adaptor tubing into
the D-piece. Ensure a tight fit.
6. Verify the gauge on the regulator-flow meter is
registering gas (arrow is not on zero)
www.covita.net | 800-707-5751
Copyright 2018 coVita LLC All Rights Reserve v042618
Firmware ≤ V2.31
D. Calibraon
IMPORTANT Do not connect the cali-a aptor or D-piece to the monitor
until after the monitor zeros (Step 5)
1. Press Gear Icon
2. Press Calibration
Icon to begin auto-
zero process
3. Monitor will
display hour glass
while zeroing
4. Assemble
calibration kit (already
done) then press the
arrow
5. Insert D-piece with
the cali-adaptor
|attached into monitor,
then press the arrow
6. Turn the gas on,
then press the arrow
7. Hour glass will
display as the moni-
tor is calibrating
8. Calibration is suc-
cessful when a check
mark is received.
**IMPORTANT**
Must press the
check mark to lock
in the calibration.
E. Addional Screens & Tips
Failed Calibration Screen
You must perform a
reset on the monitor.
Please see
section F.
Monitor temperature is
too hot. You must turn
off the monitor for a
minimum of 5 minutes
before calibrating
Monitor temperature
is too cold. You must
move your monitor to
a room temperature
environment before
calibrating
Calibration reminder to
prompt you to calibrate
every 6 months.
Press the arrow to start
calibrating.
Micro+™basic, baby, & pro
Smokerlyzer®
Calibration Gui e
www.covita.net | 800-707-5751
Copyright 2018 coVita LLC All Rights Reserve v050118
Firmware ≤ V2.31
IMPORTANT Do not connect the cali-adaptor or D-piece to the monitor unl a'er
the monitor zeros (Step 5)
1. Turn on your
monitor. Be sure
the D-piece is re-
moved from moni-
tor until
step 5.
2. Using an opened
paper clip, press/hold
the reset button located
in the battery compart-
ment in for 30 secon s
until the monitor beeps &
turns off and then
release.
3. Turn on your
monitor and the
hour glass will
appear while
automatically
zeroing
4. Assemble
calibration kit (already
done) then press the
arrow
5. Insert D-piece with
the cali-adaptor
|attached into monitor,
then press the arrow
6. Turn the gas on,
then press the arrow
7. An hour glass &
numbers will
display as the
monitor is
calibrating.
8. Calibration is suc-
cessful when a check
mark is received.
**IMPORTANT**
Must press the
check mark to lock
in the calibration.
G. Addional Screens & Tips
Failed Calibration Screen
Allow 5 minutes with
D-piece removed from
monitor and then try
calibrating again.
Monitor temperature is
too hot. You must turn
off the monitor for a
minimum of 5 minutes
before calibrating
Monitor temperature
is too cold. You must
move your monitor to
a room temperature
environment before
calibrating
Calibration reminder to
prompt you to calibrate
every 6 months.
Press the arrow to start
calibrating.
F. Reset & Calibraon
Micro+™basic, baby, & pro
Smokerlyzer®
Reset & Calibration Gui e
11
Questo manuale è adatto per i seguenti modelli
2
Altri manuali Covita Apparecchiature di prova
Covita
Covita Smokerlyzer Istruzioni per il montaggio
Covita
Covita COmpactUSB Manuale utente
Covita
Covita Gastro+ Gastrolyzer Manuale utente
Covita
Covita Smokerlyzer Micro+ Manuale utente
Covita
Covita Smokerlyzer Micro+ Manuale utente
Covita
Covita iCO Smokerlyzer Manuale utente
Covita
Covita Smokerlyzer Micro+ Manuale utente
Covita
Covita Gastro+ Gastrolyzer Manuale per l'uso e la cura
Covita
Covita piCO+ Smokerlyzer Manuale utente
Covita
Covita micro+ smokelyzer Manuale utente
Manuali Apparecchiature di prova popolari di altre marche
SMART
SMART KANAAD SBT XTREME 3G Series Manuale utente
Agilent Technologies
Agilent Technologies BERT Serial Manuale utente
Agilent Technologies
Agilent Technologies N3280A Manuale utente
Vernier
Vernier Go Direct Voltage Manuale utente
Lifeloc
Lifeloc R.A.D.A.R. Manuale utente
Fluke
Fluke T5-600 Istruzioni per l'uso e l'installazione
