Craftsman 315.235360 Manuale utente

Owner's Manual

CRIIFTSMFIW

AccESSORIES FOR THE

10 in. (254 mm) COMPOUND MITER SAW

Model No.

315.235360

Item No.

_923537

(accessories optional)

_923536

(accessories included)

Save this manual for

future reference.

CAUTION: Read and

followallSafety Rulesand

Operating Instructionsbefore

firstuseofthisproduct.

•SAFETY

•LOOSE PARTS

•INSTALLATION

•SERVICES

Sears, Roebuck and Co., Hoffman Estates, IL 60179 USA

972000-485

1-98

READ ALL INSTRUCTIONS •

...... L,"

•READ THESE INSTRUCTIONS AND THE

-INS_ 315;235360 COM-

._PQI.LNDMLT.EB.._.A.__TJ:!_ROUGHLY before •

using accessories._ .:_::!_ _,

•KNOW YOUR POWER TOQL Read the owner's

m_n_r f0Pthe (3ompo-u-h_'MiterSaw carefully.

•Lear_-tht_w_ and i'mitations as •

we.!! as.thesp._otential hazards related to

this tool.

KEEP THE WORK AREA CLEAN. Cluttered

work areas and work benches invite accidents.

DO NOT leave tools or pieces of wood on the

saw while it is in operation.

ALWAYS WEAR SAFETY GLASSES. Everyday

eyeglasses have only impact-resistant lenses;

they are NOT safety glasses.

ALWAYS DISCONNECT SAW FROM POWER

SUPPLY BEFORE MAKING ADJUSTMENTS

OR ADDING ACCESSORIES. Make sure the

switch is off when reconnecting to power supply.

SAVE THESE INSTRUCTIONS. Refer to them

frequently and use to instruct other users, if you

loan someone this tool, loan them these instruc-

tions also.

_k Look for this symbol to point out important safety precautions. It

means attention!!! Your safety is involved.

The following accessories are included with item no. _23536. They are optional and may also be purchased for

use with item no. 92.3537:

•Work Clamp (item no. _'23461)

•8 mm Work Clamp Screw (Included with

Work Clamp)

• Dust Bag (Item no. 9-23466)

• Owner's Manual

•Stop Block (Included with Table Extensions)

•Table Extensions (2) (Item no. _23464)

• Large Wing Screws(2) (Included with Table

Extensions)

• Small Wing Screw (Included with Table

Extensions)

WORKCLAMP

_8mm

WORKCLAMPSCREW

LARGEWINGSCREWS

SMALLWINGSCREW

_WARNING: The use of attachments or accessories not listed might be hazardous.

Fig, 1

AWARNING: To prevent accidental starting that

could cause possible serious personal injury,

assemble all parts to your saw completely before

connecting itto power supply• Saw should never

be connected to power supply when you are

assembling parts, making adjustments, installing

or removing blades or accessodas, or when not

in use.

WORK CLAMP

See Figure 2.

The work clamp (Item no. 92.3461) provides greater

control by clamping the workpiece to the fence. It

also prevents the workpiece from creeping toward the

saw blade. This is very helpful when cutting com-

pound miters. To install the work clamp, place the

shaft of the clamp in either hole in front of the miter

table base. Thread the 8 mm work clamp screw

provided into the side of the base and tighten itto

secure the clamp in position. Rotate the knob on the

clamp to move it in or out as needed.

_IL WARNING: Make sure the saw blade or blade

guard will not hit the work clamp assembly when

cutting 35° to 45° angles. Failure to heed this

warning can result in serious personal injury.

EXHAUSTPORT

Fig. 3

TABLE EXTENSIONS

See Figure 4.

To install the table extensions (Item no. _23464),

insert the ends of the extensions intothe holes in the

sides of the base. Adjust the extensions to the desired

length. To secure them in place, screw the two large

wing screws provided intothe holes in the front ofthe

base and tighten them securely.

8 mmWORK

CLAMP

SCREW

tVORK

CLAMP

°DUST BAG

See Figure 3. -:

Fig. 2

The dust bag (Item no. 923466) fits over the exhaust

port on the upper blade guard. To install it, remove

the dust guide from the exhaust port. Then, squeeze

the two metal clips to open the mouth of the bag and

slide it on the exhaust port. Release the clips. The

metal ring in the bag should lock in between the

grooves on the exhaust port. For more efficient

operation, empty dust bag when no more than half

•_ This will permit better air flow through the bag.

STOPBLOCK

SMALL

WIN4

TABLEEXTENSION

; SCREW

Fig. 4

STOP BLOCK

See Figures 4 and 5.

The stop block is useful as a stop for cutting multiple

pieces to the same length. It can be installed on either

table extension on either side of the saw base:

•Slide the stop block on the back arm of either

table extension, then insert the table extension

into the saw base. See Figure 4.

•Use the large wing screws to secure the table

extensions to the saw base and the small wing

screw to secure the stop block to the table exten-

sion. See Figure 4.

•Loosen the small wing screw and adjust the stop

block the desired distance from the blade for the

cut to be made.

•Tighten small wing_screw securely.

•Make a test cut in scrap material and measure the

length of the workpiece.

•Make any necessary adjustments.

_1= WARNING: When using the work clamp with

the stop block, install the clamp on the stop block

side of the blade. This will eliminate the

possibility of the saw catching the loose end and

kicking up. Failure to heed this warning can

result in serious personal injury.

STOP

BLOCK

Fig. 5

Fortherepair orreplacementparts

youneeddelivereddirectlyto yourhome

Call7 am - 7 pm, 7daysaweek

1-8OO-366-PART

(1-800-366-7278)

Forrepairservice

Call24 hoursa day,7 daysaweek

1-800-4-REPAIR

_(!-800-473-7247)

SEARS

America's Repair Specialists

Forthe location of a

SearsPads andRepairCenter

inyourarea

Call24 hoursaday,7 daysaweek

1-8OO-488-1222

Whenrequestingserviceororderingparts,

alwaysprovidethe followinginformation:

•ProductName

10 inchCompound

Miter Saw

• ModelNumber

315.235360

•PartName •Part Number

Altri manuali per 315.235360

Questo manuale è adatto per i seguenti modelli

Altri manuali Craftsman Accessori

Craftsman

Craftsman 358.792443 Manuale utente

Craftsman

Craftsman 486.24586 Manuale utente

Craftsman

Craftsman BACKWALL WITH METAL PEGBOARD Manuale utente

Craftsman

Craftsman 358.792401 Manuale utente

Craftsman

Craftsman 183.287660 Guida rapida alla configurazione

Craftsman

Craftsman 486.246211 Manuale utente

Craftsman

Craftsman 486.24100 Manuale utente

Craftsman

Craftsman 944.511591 Manuale utente

Craftsman

Craftsman 486.24611 Manuale utente

Craftsman

Craftsman 358.792421 Manuale utente

Craftsman

Craftsman 315.212400 Manuale utente

Craftsman

Craftsman 486.24635 Manuale utente

Craftsman

Craftsman 152.298890 Manuale utente

Craftsman

Craftsman ASF 486.246213 Manuale utente

Craftsman

Craftsman 315.25790 Manuale utente

Craftsman

Craftsman 320.16494 Manuale utente

Craftsman

Craftsman CMHT77636 Manuale utente

Craftsman

Craftsman Trimmer Products Manuale utente

Craftsman

Craftsman 486.24545 Manuale utente

Craftsman

Craftsman 486.24599 Manuale utente

Craftsman

Craftsman 320.16495 Manuale utente

Craftsman

Craftsman 22252 Manuale utente

Craftsman

Craftsman 509344 Manuale utente

Craftsman

Craftsman 572.530331 Manuale utente

Manuali Accessori popolari di altre marche

Hillco

Hillco 2810 Manuale utente

Siemens

Siemens QSA2700D Manuale dell'operatore

Contours

Contours ZY024 Manuale utente

Saivod

Saivod VS621 Manuale utente

Virtuox

Virtuox VirtuCLEAN 2.0 Manuale utente

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Manuale utente

Z-Wave

Z-Wave HSD-200Z Manuale utente

turck

turck FMX-IM-2UPLI63FX Manuale utente

Decagon Devices

Decagon Devices 10HS Manuale utente

UPPAbaby

UPPAbaby Cup Holder Manuale utente

Elko

Elko SmartSensor Leakage Wireless Manuale utente

Grizzly

Grizzly H8371 Manuale utente

Panasonic

Panasonic HG-T Series Manuale utente

IFM Electronic

IFM Electronic Efector 250 Series Guida di riferimento

DigiDesign

DigiDesign 888/24 I/O Manuale utente

PROZIS

PROZIS QUAY Manuale utente

patagonia

patagonia PSI Vest Manuale utente

SFC Energy

SFC Energy EFOY GO! Manuale utente