Creality CR-10 Series Manuale
This guide is for the CR-10 Series of 3D printers. It is also
applicable for the CR-10S/CR-10 S4/CR-10 S5.
Among them, CR-10 mini without T-Bracket (Right) &
Decoration Strip.
Due to the different types of device in the hardware and
software upgrade industry. the products are slightly
different and it is a noemal phenomenon. Subject to actual
product received.
Detailed instructions for use are available on the TF card.
V4.1
CR-10 Series 3D Printer
Guide Book
To be the Chief Evangelist
【To make Top-quality 3D printer】
Notes
1. Do not use the Printer in any other way not described herein in order to avoid personal injury or
property damage.
2. Do not place the Printer near flammables, explosives or heat sources. It is best to place it in a well-
ventilated, low-dust environment.
3. Do not expose the Printer to violent vibration or any unstable environment, because this will cause
poor print quality.
4. The Filaments recommended by the manufacturer are preferred as to avoid clogging in the extrusion
head or Printer damage.
5. Do not use any other power cable except the one supplied. Use a grounded three-prong power
outlet.
6. Do not touch the nozzle or hot bed during printing. Keep hands away from machine while in use to
avoid burns or personal injury.
7. Do not wear gloves or loose clothing when operating the Printer. Preventing the movable parts from
being involved in the squeeze or cutting injury to hunman boday or printer damage.
8. Clean off filament from the nozzle tip with the provided pliers before the nozzle cools. Do not touch
the nozzle directly. This can cause personal injury.
9. Clean the Printer frequently. Usually clean it while power-off, clean the body of the machine with a
dry cloth to remove dust, adhered printing materials and other material of the guide rails. Use glass
cleaner or isopropyl Alcohol to clean the print surface before every print for consistent results.
10. Children under 10 years of age should not use the Printer without supervision.
Preface
Contents
Dear consumers,
Thank you for choosing our products. For the best experience, please read the instructions before
operating the Printer. Our 3D team is always ready to provide you with assistance. Please contact us via
the phone number or e-mail address provided at the end when you encounter any problem with the Printer.
For a better experience in using our product, you may learn how to use the Printer in the following ways:
1. View the accompanied instructions and videos on the SD card.
2. Visit our official website at www.creality3d.cnYou will find relevant software/hardware information,
contact details and operation and maintenance instructions on the website.
1. Introduction....................................1
2. General List ....................................2
3. Device Installion ............................3
4. Cable Connection...........................5
5. Screen Information………………….6
6. Loading Filament ….………………7
7. Bed Leveling ..……...…………………8
8. Software Installation ..………………9
9. For the first Printing…………………....10
10. T r o u b l e s h o o t i n g . . . . . . . . . . . . . . . . . . 1 1
11. After-Sales Services …………………12
1
1. Display Screen
2. Control Knob
3. Voltage Selection
4. TF Slot and USB Port
5. Nozzle Kit
6. Platform
7. Base Frame
8. Z Gantry Frame
9. Y Stepper
10. Y Limit Switch
11. Z Stepper
12. Z Limit Switch
13. X Stepper
14. Spool Holder
15. Control Box
16. Nozzle Assembly Connection
17. Hot Bed Connection
18. Power Cable Connection
19. Extruder (E) Stepper
20. X Limit Switch
1. Introduction
1
2
14
17
19
20
15
16
18
9 10 11 12 134
35678
Tool List
*CR-10 mini without T-Bracket (Right) &
Decoration Strip.
2.General List
Base Frame Gantry Frame Control Box Tool Kit
No.
Image
Name
Qty
No.
Image
Name
Qty
No.
Image
Name
Qty
1
Spool Holder & Nuts
1
6
M5X25 Bolt
& Lock Washer
4
sets
12
Scraper
1
2
Spool Holder Bracket
1
7
Power Cable
1
13
Diagonal Pliers
1
3
Sample Filament
(200g)
1
8
USB Cable
1
14
Hex keys, Wrench
& Screwdriver
1
9
TF Card
& Card Reader
1
15
Cable Ties
1
4
T-Bracket (Right)
1
10
PTFE Tubing
(spare part)
1
16
Spare Parts
1
5
T-Bracket
& Z Limit Switch (Left)
1
11
Nozzle Cleaner
1
17
Decorative Trim
1
2
3
Install the Gantry Frame
Insert the Teflon pipe into
the quick connector
*CR-10 mini without T-Bracket (right).
M5X25
4pcs
Note: Make sure that the nut
for profile has been turned by
90° before fastening the
T-shaped fixing block.
3.Device Installtion 01
Install the T-shaped fixing block.
4
◆ Install the Spool Holder and Bracket
◆ Installation decoration
belt
Attach the Bracket with
two thumb screws. Attach Spool Holder
with included Nuts
Finished
Installation decoration belt into
the notch, starting from one end.
Cut off the excess material with
the diagonal pliers
Attach the Decorative Trim to all
parts needing to be decorated.
*Installation decoration belt is available in various colors. The pictures above are for reference only.
*CR-10 mini without Decoration Strip.
3.Device Installtion 02
Extruder (E) Stepper
X Stepper and Limit Switch
Y Stepper and Limit Switch
Z Stepper and Limit Switch
Connect the Stepper Motors according to
the yellow labels on the 6pin (4-wire) side.
Connect the Limit Switches according to
the yellow labels on the 3pin (2-wire) side.
•Select the correct input voltage to match your local
mains (220V or 110V)
•Damage can occur if voltage is set incorrectly.
•Make sure the power cable is connected.
5
Connect the aviation connectors
to the ports with corresponding
pins
Now your 3D printer is assembled!
4.Cable Connection
6
Set Temperature of
the Nozzle
Current Temperature
of the Nozzle
Set Temperature of
the Hot Bed
Current Temperature
of the Hot Bed
Part Cooling Fan
Speed
Current Location of
the nozzle
Print Time
Print Progress
Prompt Message
Print Speed
Device Model
Push：OK/Enter Sub Menu
Turn：Change Option/Value
5.Screen Information
7
1. Preheat
Method 1
Method 2
2.Feeding
Tip：How to Replace the Filament？
1、Cutting filament near the Extruder and slowly feed
new filament until they are fed into the new filament.
2、Preheating the nozzle and withdraw the filament
quickly and feed the new filament.
Press and hold the extruder lever then insert
the1.75mm filament through the small hole of the
extruder. Continue feeding until you see filament
come out the nozzle.
6.Loading Filament
Altri manuali per CR-10 Series
5
Indice
Altri manuali Creality Stampante 3D
Creality
Creality CR-Laser Falcon Manuale utente
Creality
Creality CR-10S Pro Manuale
Creality
Creality Ender 3 Pro Manuale utente
Creality
Creality CR-10S Pro Manuale utente
Creality
Creality CR-10 Smart Manuale utente
Creality
Creality CR-Laser Falcon Manuale utente
Creality
Creality HALOT-ONE PLUS Manuale utente
Creality
Creality K1 Manuale utente
Creality
Creality CR-5 Manuale utente
Creality
Creality Ender-3 Manuale utente
Creality
Creality CR-10 Smart Manuale utente
Creality
Creality CR-6 SE Manuale utente
Creality
Creality K1 Max Manuale utente
Creality
Creality CREALITY BOX Manuale utente
Creality
Creality Spider Manuale utente
Creality
Creality Ender-5 Manuale
Creality
Creality HALOT-LITE Manuale utente
Creality
Creality AL-BMG Manuale utente
Creality
Creality HALOT-LITE CL-89L Manuale utente
Creality
Creality Dual Z Manuale utente
