Creda W810 Manuale utente

You can read the recommendations in the user guide, the technical guide or the installation guide for CREDA HBW810. You'll find

the answers to all your questions on the CREDA HBW810 in the user manual (information, specifications, safety advice, size,

accessories, etc.). Detailed instructions for use are in the User's Guide.

User manual CREDA HBW810

User guide CREDA HBW810

Operating instructions CREDA HBW810

Instructions for use CREDA HBW810

Instruction manual CREDA HBW810

You're reading an excerpt. Click here to read official CREDA

HBW810 user guide

http://somemanuals.com/dref/16895

Manual abstract:

To the Installer Before installation fill in the product details on the back cover of this booklet. The information can be found on the rating plate. To the User

You must read the instructions prior to using the appliance and then retain them for future reference. FP089-01 Creda Gas Hob (W810) 12/09/2001 5:02 pm

Page 2 CONTENTS Introduction For Your Safety Always For Your Safety Never Using The Hob Care & Cleaning Something Wrong? Installation Key

contacts 3 4 5 6 7 8 9 - 14 Back Cover Retention of this Instruction Book This Instruction Book must be kept handy for reference as it contains important

details on the safe and proper use of the appliance. If you sell or pass the appliance to someone else, or move house and leave it behind, make sure this Book

is also provided so the new owner can become familiar with the appliance and safety warnings. If the Book is lost or damaged a copy may be obtained from

GDA Ltd, Morley Way, Peterborough, PE2 9JB. 2 FP089-01 Creda Gas Hob (W810) 12/09/2001 5:02 pm Page 3 INTRODUCTION Your new hob is

guaranteed* and will give lasting service. This guarantee is only applicable if the appliance has been installed in accordance with the installation instructions

detailed in this booklet. To help make best use of your cooking equipment, please read this booklet carefully. The hob is designed specifically for domestic use

and responsibility will not be accepted for use in any other installation.

* The guarantee is subject to the provisions that the appliance: (a) (b) (c) (d) Has been used solely in accordance with the Users Instruction Book. Has been

properly connected to a suitable supply voltage and gas supply as stated on the rating plate attached to this equipment. Has not been subjected to misuse or

accident or been modified or repaired by any person other than the authorised employee or agent. Has been correctly installed. 3 FP089-01 Creda Gas Hob

(W810) 12/09/2001 5:02 pm Page 4 FOR YOUR SAFETY When used properly, your appliance is completely safe but as with any product there are certain

precautions that must be observed.

PLEASE READ THE PRECAUTIONS BELOW BEFORE USING YOUR APPLIANCE. ALWAYS q q q q q q q q q q q Always make sure you understand the

controls prior to using the appliance. Always keep children away from the appliance when in use as the surfaces will get extremely hot during and after

cooking. Always make sure all controls are turned off when you have finished cooking and when not in use. Always take care to avoid heat/steam burns when

operating the controls.

Always turn off the electricity supply at the wall switch and allow the appliance to cool before cleaning . Always keep the appliance clean as a build up of

grease or fat from cooking can cause a fire. Always follow the basic principles of food handling and hygiene to prevent the possibility of bacterial growth.

Always refer servicing to a qualified appliance service engineer. Always dry food thoroughly before frying, and lower it slowly into the hot oil or fat. Frozen

foods, in particular, will cause frothing and spitting, if added too quickly. Always keep the outside of the pan clean and free from streaks of oil or fat. Always

place pans centrally over the burner making sure handles are kept away from the edge of the hob and cannot become heated by other burners / pans. SAFETY

ADVICE IMPORTANT - As with any cooking appliance there could be some fire risk attached to the heating of oil, particularly for deep fat frying. Cooking

utensils containing oil must not be left unattended (e.

g. to answer the telephone) on or in close proximity to the cooking areas. IN THE EVENT OF A CHIP PAN OR ANY OTHER PAN FIRE: 1. 2. 3. TURN OFF

THE BURNERS. COVER THE PAN WITH A FIRE BLANKET OR DAMP CLOTH, this will smother the flames and extinguish the fire. LEAVE THE PAN TO

COOL FOR AT LEAST 60 MINUTES BEFORE MOVING IT. Injuries are often caused by picking up a hot pan and rushing outside with it. NEVER USE A

FIRE EXTINGUISHER TO PUT OUT A PAN FIRE as the force of the extinguisher is likely to tip the pan over.

You're reading an excerpt. Click here to read official CREDA

HBW810 user guide

http://somemanuals.com/dref/16895

Never use water to extinguish oil or fat fires 4 FP089-01 Creda Gas Hob (W810) 12/09/2001 5:02 pm Page 5 FOR YOUR SAFETY NEVER q q q q q q q q q

q q q q Never leave children unsupervised where a cooking appliance is installed as all cooking surfaces will be hot during and after use. Never allow anyone

to sit or stand on any part of the appliance. Never store items above the appliance that children may attempt to reach. Never leave anything on the hob

surface when unattended and not in use. Never heat up unopened food containers as pressure can build up causing the container to burst.

Never store chemicals, food stuffs or pressurised containers in or on the appliance, or in cabinets immediately above or next to the appliance. Never place

aluminium or plastic foil or plastic containers directly on the hob surface. Never fill a deep fat frying pan more than 1/3 full of oil, or use a lid. DO NOT

LEAVE UNATTENDED WHILE COOKING. Never use the appliance as a room heater.

Never dry any items on the hob. Never use misshapen pans which may be unstable. Never use round base woks directly on the pan supports. Never use fish

kettles or large preserving pans across two burners. NOTE: The use of a gas cooking appliance results in the production of heat and moisture in the room in

which it is installed. Always ensure that the kitchen is well ventilated; keep natural ventilation holes open or install a mechanical ventilation device

(mechanical extractor hood). In particular, when using the grill or more than one hotplate burner, open a window if a mechanical ventilation device is not

operating. 5 FP089-01 Creda Gas Hob (W810) 12/09/2001 5:02 pm Page 6 USING THE GAS HOB - FEATURES In order to obtain maximum performance

from the burners, use pans with the following diameters: Rapid burner 22 - 28 cm Standard burner 14 - 22 cm Auxillary burner 10 - 14 cm All pans should be

positioned centrally over the burners. DO NOT allow young children near to the appliance when the hob is in use as the surfaces get extremely hot.

OPERATION WHEN USING THE GAS HOB Step 1 Step 2 Step 3 Step 4 Step 5 Check that the electricity is switched ON.

Press the ignition button and then push and turn the control knob of the chosen burner anticlockwise to the large flame symbol. The gas should then ignite.

Turn the control knob anticlockwise to the desired setting. Only turn the control knob between the large flame symbol and the small flame symbol when

adjusting the setting. Place the pan centrally on the required burner. To switch off, turn the control knob fully clockwise. 6 FP089-01 Creda Gas Hob (W810)

12/09/2001 5:02 pm Page 7 CARE AND CLEANING SWITCH OFF THE ELECTRICITY SUPPLY BEFORE CLEANING. BEFORE SWITCHING ON AGAIN,

ENSURE THAT ALL CONTROLS ARE IN THE OFF POSITION. NEVER USE BIOLOGICAL WASHING POWDER, HARSH ABRASIVES, SCOURING

PADS, AEROSOL CLEANERS OR OVEN CHEMICAL CLEANERS OF ANY KIND. Clean the hob regularly and wipe up spills soon after they occur to

prevent them from becoming burnt on.

CLEANING MATERIALS TO AVOID 1. Household abrasive powders, e.g. Vim. 2.

Oven chemical cleaners, aerosols and oven pads. Caustic cleaners such as these will etch the surface and attack the metal frame. 3. Bath and sink cleaners

may mark the surface. VITREOUS ENAMEL HOB, PAN SUPPORTS AND BURNER CAPS.

Wipe with a cloth wrung out in hot soapy water. Stubborn stains can be removed with a cream paste or liquid cleaner. STAINLESS STEEL. Wipe with a cloth

wrung out in hot soapy water followed by a wipe with a cloth wrung out in clear water and then dried with a soft clean cloth. ALUMINIUM BURNER

BODIES AND RINGS. Wipe with a cloth wrung out in hot soapy water only; do not use abrasives. Use a nylon brush to remove any cleaning materials, water

or dirt from the burner bodies. Re-assemble as in the diagram below. CONTROL KNOBS. Wipe over the knobs with a soft cloth wrung out in hot soapy water

or mild non-abrasive cleaner.

Then, after wiping with a cloth wrung out in clear water, dry with a soft clean cloth.

You're reading an excerpt. Click here to read official CREDA

HBW810 user guide

http://somemanuals.com/dref/16895

Never use scouring pads or abrasive cleaners/powders which may scratch the surface. BURNER ASSEMBLY 7 FP089-01 Creda Gas Hob (W810)

12/09/2001 5:02 pm Page 8 SOMETHING WRONG ? IF THE IGNITION DOES NOT WORK Is the electricity switched on? If the electricity supply has

failed, the burners can be lit with a match. If only a hotplate burner is failing to ignite, check that the burner body and cap are seated correctly and that the

slots in the burner body are not blocked (see care and cleaning). May we wish you many years of carefree successful cooking. Disposal of your product To

minimise the risk of injury to children please dispose of your product carefully and safely. Remove all doors and lids (where fitted). Remove the mains cable

(where fitted) by cutting off flush with the appliance and always ensure that no plug is left in a condition where it could be connected to the electricity supply.

To help the environment, Local Authority instructions should be followed for the disposal of you product. This appliance conforms to the following EEC

Directives: Low Voltage Equipment 73/23/EEC 93/68/EEC Electromagnetic Compatibility 89/336/EEC 92/31/EEC 93/68/EEC Gas Appliances 90/396/EEC

93/68/EEC 8 FP089-01 Creda Gas Hob (W810) 12/09/2001 5:02 pm Page 9 INSTALLATION - electrical requirements WARNING THIS APPLIANCE MUST

BE EARTHED.

CONNECT TO A 230-240V A.C. SUPPLY ONLY. Connection to the electricity supply should be made via a properly earthed, readily accessible wall socket

which is adjacent to but not directly above, and not more than 1.25m away from the appliance and capable of electrical isolation.

Should this plug not fit the socket outlet in your home it should be cut off and replaced with a suitable plug as outlined below. NOTE: The removed plug

cannot be used for any other appliance and should therefore be properly disposed of and not left where children might find it and plug it into a supply socket

with the obvious consequent danger. IF THE FITTED PLUG IS REMOVED The flexible mains lead must be correctly connected as below to a three pin plug

of not less than 13 amp capacity. If a B.S.

1363 fused plug is used, it must be fitted with a 3 amp fuse which is approved to B.S. 1362. IMPORTANT: The wires in the mains lead fitted to this appliance

are coloured in accordance with the following code: GREEN AND YELLOW EARTH BLUE NEUTRAL BROWN LIVE Blue to Neutral Cord Clamp Green

& Yellow to Earth Brown to Live 3 Amp Fuse As the colours of the wires in the mains lead of this appliance may not correspond with the coloured markings

identifying the terminals in your plug, proceed as follows: The wire which is coloured green and yellow must be connected to the terminal in the plug which is

marked with the letter E or by the earth symbol or coloured green or green and yellow. The wire which is coloured blue must be connected to the terminal

which is marked with the N or coloured black. The wire which is coloured brown must be connected to the terminal which is marked with the letter L or

coloured red. When wiring the plug, ensure that all strands of wire are securely retained in each terminal. Do not forget to tighten the mains lead clamp on

the plug. As the appliance must be earthed, do not use 2-pin sockets outlets, if you are in doubt, consult a qualified electrician. Should the mains lead ever

require replacement, it is essential that this operation be carried out by a qualified electrician and should only be replaced with a flexible cord of the same

size i.

e. 0.75mm2 cross sectional area and temperature rating of 850 C e.g. heat resisting PVC. IF A MOULDED PLUG IS FITTED In the event of replacing a fuse

in the plug supplied a 3 amp ASTA approved fuse to BS1362 must be fitted. NOTE: The fuse cover must be refitted when changing the fuse. In the event of

losing the fuse cover the plug must not be used until a replacement fuse cover has been obtained and fitted. A new fuse cover can be obtained from your local

Electricity Board.

You're reading an excerpt. Click here to read official CREDA

HBW810 user guide

http://somemanuals.com/dref/16895

The colour of the correct replacement fuse cover is that of the coloured marks or inserts in the base of the plug.

Make sure that the cable does not become trapped. 9 FP089-01 Creda Gas Hob (W810) 12/09/2001 5:02 pm Page 10 INSTALLATION INSTRUCTIONS Gas

Category II2H3+ (GB,IE) Model Numbers W810, BG05 These models are set to burn NATURAL GAS (G20) at 20mbar. They can also be converted to burn

BUTANE GAS (G30) at 28mbar or PROPANE GAS (G31) at 37mbar using the conversion kit included. Technical Data Gas Connection Pressure test point

Rp 1/4 (1/4" BSP female) Burner injector Gas rate adjustment None Aeration adjustment None Electrical Connection 230-240V ac. 50Hz Heat resistant PVC

85oC 0.

75mm2 Flexible cord. Natural Gas BURNER Front Left Rear Right and Rear Left Front Right HEAT INPUT 3.0 kW 2.0 kW 1.15kW INJECTOR 130 105 80

LPG HEAT INPUT 3.

0 kW 2.0 kW 1.15kW INJECTOR 92 72 55 10 FP089-01 Creda Gas Hob (W810) 12/09/2001 5:02 pm Page 11 INSTALLATION INSTRUCTIONS Prior to

installation, ensure that the local distributions (nature of the gas and gas pressure) and the adjustment conditions are compatible. The adjustment conditions

for this appliance are stated on the rating plate which is fitted on the underside of the base panel. This appliance is not designed to be connected to a

combustion products evacuation device. It must be installed and connected in accordance with current installation regulations. Particular attention should be

given to the relevant requirements regarding ventilation. GAS SAFETY (INSTALLATION & USE) REGULATIONS It is the law that all gas appliances are

installed by competent persons in accordance with the current edition of the above regulations. It is in your interest and that of safety to ensure compliance

with the law. In the UK, CORGI registered installers work to safe standards of practice.

The cooker must also be installed in accordance with BS 6172: Failure to install the cooker correctly could invalidate the warranty liability claims and could

lead to prosecution. LOCATION The cooker may be located in a kitchen, kitchen/diner or a bed-sitting room, but not in a room containing a bath or shower.

The cooker must not be installed in a bedsitting room of less than 20m3. PROVISION FOR VENTILATION The room containing the cooker should have an

air supply in accordance with BS 5440: Part 2. The room must have an opening window or equivalent; some rooms may also require a permanent vent. If the

room has a volume between 5 and 10m3, it will require an air vent of 50cm2 effective area unless it has a door which opens directly to outside. If the room

has a volume of less than 5m3, it will require an air vent of 100cm2 effective area. If there are other fuel burning appliances in the same room, BS 5440: Part

2 should be consulted to determine air vent requirements. 11 FP089-01 Creda Gas Hob (W810) 12/09/2001 5:02 pm Page 12 INSTALLATION SITING THE

HOB The hob is designed to fit into worktop and base unit(s) with a cutout as shown in Fig.1.

Any obstruction such as supports or side panels must be removed to allow 30mm minimum depth below the worktop cutout. Any overhead surface of

combustible material must not be closer than 600mm. When installing next to a tall cupboard, partition or wall, for a minimum distance of 400mm above the

hotplate a side clearance of at least 40mm should be allowed from the edge of the cutout. This is a type X appliance regarding installation requirements, it is

recommended that a shelf is fitted to the cabinet under the hob, but no closer than 10mm to prevent access to the underside of the hob which will become hot

when in use. If a cooker hood is to be installed refer to the manufacturer's instructions regarding fixing heights.

FITTING THE HOB Unpack the hob from the carton. Remove the bag containing the sealing tape, fixing brackets, screws and gas inlet elbow. Fit the sealing

tape around the edge of the cut-out in the worktop. Connect the gas inlet elbow supplied to the end of the hob gas pipe.

You're reading an excerpt. Click here to read official CREDA

HBW810 user guide

http://somemanuals.com/dref/16895

During installation, it is important not to twist the hob gas pipe when connecting to or adjusting the position of the gas inlet elbow to avoid the possibility of

disturbing gas tight joints inside the hob.

Ensure that the inlet is held securely: * When loosening or tightening the hob gas pipe securing nut. * When connecting fittings to it. Also, ensure that

connecting pipe work does not twist the inlet elbow away from its free position. Lower the hob into the worktop ensuring the mains lead is fed into the base

unit and is not trapped under the flanges. Fix the hob to the worktop using the fixing brackets and screws. NB Do not over tighten the hob clamps as distortion

of the hob may occur. Connect the hob to the gas supply and check for gas soundness. If a flexible hose is used for connection, it should be fitted such that it

cannot come into contact with moveable parts of the housing (e.g. a drawer), does not pass through a space where it is likely to become trapped or damaged

and hangs freely downwards.

The temperature rise of the area of the base panel likely to come into contact with a flexible hose does not exceed 70ºC Connection must be by rigid pipework

when the hob is installed above an oven. Put the burner rings and caps into position. Connect the hob to the electrical supply (see INSTALLATION -

Electrical Requirements). Ensure that the hob is functioning correctly prior to use. Instruct the user in the operation of the hob. 12 FP089-01 Creda Gas Hob

(W810) 12/09/2001 5:02 pm Page 13 INSTALLATION Fig. 1 IMPORTANT Minimum unobstructed depth 30mm 558 mm Front edge of worktop 50mm mm

489 Worktop thickness Preferred 30-40mm 19mm minimum recommended Fig. 2 FIXING CLAMP Note: Do not over tighten the hob clamps as distortion of

the hob may occur. 13 FP089-01 Creda Gas Hob (W810) 12/09/2001 5:02 pm Page 14 INSTALLATION INSTRUCTIONS LPG Conversion Instructions for

Model W810, BG05 Read the Gas Hob instructions before conversion, installation and using the Gas Hob. Contents of kit: 1 2 3 Rapid burner injector

marked 92 - 1 off Semi-rapid burner injector marked 72 - 2 off Auxillary burner injector marked 55 - 1 off Hotplate Burner Injector Change and Bypass

Screw Adjustment Ensure that the Gas Hob is disconnected from the gas and electricity supply (Fig.

1) 1. 2. 3. Remove pan supports, burner caps,burner bodies and control knobs (Fig.2) Remove each injector and replace with LPG injector using 7mm A/F

hexagonal socket (Fig.

3). Turn each gas tap bypass screw fully clockwise using a small flat bladed screwdriver through the holes in the control panel. The bypass screw is located to

the side of the tap spindle (Fig.4). 14 FP089-01 Creda Gas Hob (W810) 12/09/2001 5:02 pm Page 15 15 FP089-01 Creda Gas Hob (W810) 12/09/2001 5:02

pm Page 16 Key Contacts Service Creda has the largest appliance manufacturer's service team in Europe, trained specialists directly employed by us to

ensure your complete confidence.

Repair Service UK: 08709 066 066 Republic of Ireland: 1850 302 200 You will be asked for the following information:Name, address and postcode.

Telephone number Model / Serial number of the appliance Clear and concise details of the query or fault Place and Date of purchase (Please keep the receipt

as evidence will be required when the engineer calls). Extended Warranty To join: UK 08709 088 088 Republic of Ireland: 1850 502 200 Genuine Parts &

Accessories Mail Order Hotline UK: 08709 077 077 Republic of Ireland: (01) 842 6836 For further product information 08701 546575 All Creda Services

are offered as an extra benefit and do not affect your statutory rights..

You're reading an excerpt. Click here to read official CREDA

HBW810 user guide

http://somemanuals.com/dref/16895

Altri manuali per W810

Indice