Crestron CWD6609 Manuale utente

Crestron CWD6609

Two-Way RF Transceiver Module

Operations Guide

This document was prepared and written by the Technical Documentation department at:

Crestron Electronics, Inc.

15 Volvo Drive

Rockleigh, NJ 07647

1-888-CRESTRON

All brand names, product names and trademarks are the property of their respective owners.

Crestron CWD6609 Two-Way RF Transceiver Module

Contents

Two-Way RF Transceiver Module: CWD6609..............................................1

Introduction ...............................................................................................................................1

Functions and Features................................................................................................1

Specifications ..............................................................................................................2

Physical Description....................................................................................................2

Industry Compliance ...................................................................................................4

Setup..........................................................................................................................................6

Hardware Hookup .......................................................................................................6

End Product Labeling..................................................................................................7

Documentation ............................................................................................................7

Operations Guide - DOC. 6838A Contents •i

Crestron CWD6609 Two-Way RF Transceiver Module

Two-Way RF Transceiver Module:

CWD6609

Introduction Functions and Features

The CWD6609 (hereafter referred to as “module”) is a two-way radio frequency

(RF) module that utilizes the 2.4 GHz frequency band to communicate with other

devices.

The module operates according to the IEEE 802.15.4 specification and can be

configured to minimize the possibility of interference with other devices.

The module receives RF signals from one or more Crestron devices and can transmit

these signals over the air or over a cable run for further processing (depending on the

application).

Functional Summary

•Two-way RF transceiver

−2.4 GHz frequency band, IEEE 802.15.4 specification

−Range from 3 feet to 50 ft.

−Operates on one of sixteen available channels to establish optimal

nal

ualit

The transceiver uses a 1.67 milliwatt signal that can travel up to approximately 50

feet indoors. The range is dependent on the construction of the building,

obstructions, and RF interference from other devices. The location of the module and

the orientation of its antenna are also important factors in determining RF

performance.

Operations Guide - DOC. 6838A Two-Way RF Transceiver Module: CWD6609 •1

Two-Way RF Transceiver Module Crestron CWD6609

Specifications

The table below is a summary of specifications for the CWD6609.

Specifications of the CWD6609

SPECIFICATION DETAILS

Power Requirements 0.58 Watts (5.0VDC @ 0.115A)

Operating Frequency 2400 MHz to 2483.5 MHz (802.15.4 compliant)

Operating Ranges¹

Minimum Distance

Maximum Distance Indoors

(without repeater device)

3 ft

50 ft

Available Channels 16 (numbered 11 through 26 per 802.15.4)

RF Output Power 1.67 mW

Dimensions Width: 1.64 in (4.15 cm)

Height: 2.35 in (5.98 cm)

Depth: 0.66 in (1.68 cm)

1. The location and the orientation of the module are important factors in the RF performance. The

range is dependent on its placement and the building in which it is used. The construction of the

building, obstructions, and RF interference from other devices are factors determining the effective

range of the unit. To prevent unit-to-unit RF interference, multiple modules operating at the same

frequencies should not be installed within 3-5 feet of each other.

Physical Description

The module, shown below, consists of various components attached to a printed

circuit board. A circuit-board mounted antenna is located at the top of the board

while a 10-pin connector for the application-specific installation is located at the

bottom of the board.

Physical View of CWD6609

2 •Two-Way RF Transceiver Module: CWD6609 Operations Guide - DOC. 6838A

Crestron CWD6609 Two-Way RF Transceiver Module

CWD6609 Detail Views

2.35 in

(5.98 cm)

1.64 in

(4.15 cm)

Ports

The module contains a 10-pin connector. Refer to the diagram and description that

follow.

Power/I-O

10 The 10-pin connector provides power to the module as well as communications

between the module and wired devices. Refer to the following table for pin

assignments of the module interface connector.

NOTE: Pin 1 provides power to the circuit card.

Power/I-O Pinout Signals

Pin # Signal Pin # Signal

1 +5V 6 REMOTE_B/CONFIG

2 TRIAC/RELAY 7 GND

3 ZERO_X 8 3.3v

4 REMOTE_A/RELAY 9 GND

5 GND 10 GND

Operations Guide - DOC. 6838A Two-Way RF Transceiver Module: CWD6609 •3

Two-Way RF Transceiver Module Crestron CWD6609

Industry Compliance

Labeling Requirements

If the FCC ID on the CWD6609 is not visible when the module is installed inside

another device, then the outside of the device into which the module is installed must

also display a label referring to the enclosed module. This exterior label can use

wording such as the following: “Contains Transmitter Module FCC ID:

EROCWD6609” or “Contains FCC ID: EROCWD6609.” Any similar wording that

expresses the same meaning may be used.

Compliance Statement (Part 15.19 )

This device complies with Part 15 of the FCC Rules. Operation is subject to the

following two conditions:

1. This device may not cause harmful interference, and

2. This device must accept any interference received, including interference

that may cause undesired operation.

Warning (Part 15.21 )

Changes or modifications not expressly approved by the party responsible for

compliance could void the user’s authority to operate the equipment.

RF Exposure (OET Bulletin 65 )

To comply with FCC RF exposure requirements for mobile transmitting devices, this

transmitter should only be used or installed at locations where there is at least 20cm

separation distance between the antenna and all persons.

Industry Canada Statement

The term "IC" before the certification/registration number only signifies that the

Industry Canada technical specifications were met.

IC: 5683C-CWD6609

Section 7.1.5 of RSS-GEN

Operation is subject to the following two conditions:

1) this device may not cause interference, and

2) this device must accept any interference, including interference that may cause

undesired operation of the device.

FCC Radiation Exposure Statement:

This equipment complies with FCC radiation exposure limits set forth for an

uncontrolled environment. This equipment should be installed and operated with

minimum distance 20cm between the radiator & your body. This transmitter must

not be co-located or operating in conjunction with any other antenna or transmitter.

This device is intended only for OEM integrators under the following

conditions:

1. The antenna must be installed such that 20 cm is maintained between the

antenna and users, and

2. The transmitter module may not be co-located with any other transmitter or

antenna.

As long as the two conditions above are met, further transmitter test will not be

required. However, the OEM integrator is still responsible for testing their end-

product for any additional compliance requirements required with this module

installed (for example, digital device emissions, PC peripheral requirements, etc.).

4 •Two-Way RF Transceiver Module: CWD6609 Operations Guide - DOC. 6838A

Crestron CWD6609 Two-Way RF Transceiver Module

IMPORTANT NOTE: In the event that these conditions cannot be met (for

example certain laptop configurations or co-location with another transmitter), then

the FCC authorization is no longer considered valid and the FCC ID cannot be used

on the final product. In these circumstances, the OEM integrator will be responsible

for reevaluating the end product (including the transmitter) and obtaining a separate

FCC authorization.

Operations Guide - DOC. 6838A Two-Way RF Transceiver Module: CWD6609 •5

Two-Way RF Transceiver Module Crestron CWD6609

Setup

Hardware Hookup

Refer to the hookup diagram below, which shows the connections made to the

module. Complete the connections in any order.

NOTE: To prevent unit-to-unit RF interference, multiple modules operating at the

same frequencies should not be installed within three to five feet of each other.

Hookup Connections for CWD6609

ANTENNA:

TRANSMITS AND RECEIVES

RF SIGNALS

(LOCATED ON OTHER SIDE)

HOST PCB

+5V

CONTROL

For more information on these connectors, refer to “Ports” on page 3.

6 •Two-Way RF Transceiver Module: CWD6609 Operations Guide - DOC. 6838A

Indice

Altri manuali Crestron Unità di controllo

Crestron

Crestron CWD6671 Manuale utente

Crestron

Crestron APAD Istruzioni utente

Crestron

Crestron C2N-VEQ4 Manuale utente

Crestron

Crestron GLS-SIM Istruzioni operative

Crestron

Crestron CEN-IO-COM-102 Manuale utente

Crestron

Crestron PYNG-HUB Disegno dimensionale

Crestron

Crestron FT2A-PWR US Series Manuale utente

Crestron

Crestron TS-1542-IMCW Manuale utente

Crestron

Crestron CNTV Manuale utente

Crestron

Crestron CLTI-2DIMU8 Manuale utente

Crestron

Crestron BiAmp AudiaFlex Manuale utente

Crestron

Crestron INET-IOEX-IRCOM Manuale utente

Crestron

Crestron DIN-AO8 Istruzioni operative originali

Crestron

Crestron FT2A-PWR-UN-1-C14 Manuale utente

Crestron

Crestron SFP-10G-S-U Disegno dimensionale

Crestron

Crestron FT2A-PWR 1-C14 Series Manuale utente

Crestron

Crestron FlipTop FT2 Series Manuale utente

Crestron

Crestron C2N-VEQ4 Manuale utente

Crestron

Crestron CWD6790R1 Manuale utente

Crestron

Crestron C2N-FTB Come usare

Crestron

Crestron FT2A-PWR-UK-1-C14 Manuale utente

Crestron

Crestron CP3 Manuale utente

Crestron

Crestron C2N-FT-TPS4 Come usare

Crestron

Crestron DMPS3-4K-250-C Disegno dimensionale

Manuali Unità di controllo popolari di altre marche

Festo

Festo Compact Performance CP-FB6-E Manuale elenco delle parti

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuale utente

JS Automation

JS Automation MPC3034A Manuale utente

JAUDT

JAUDT SW GII 6406 Series Guida rapida

Spektrum

Spektrum Air Module System Manuale utente

BOC Edwards

BOC Edwards Q Series Manuale utente

KHADAS

KHADAS BT Magic Manuale utente

Etherma

Etherma eNEXHO-IL Manuale utente

PMFoundations

PMFoundations Attenuverter Manuale utente

GEA

GEA VARIVENT Manuale utente

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuale utente

Altronix

Altronix LINQ8PD Istruzioni per il montaggio

Eaton

Eaton Powerware Series Manuale utente

WAGO

WAGO 750-407/040-000 Manuale utente

Sony

Sony CCU-590 Manuale utente

Graco

Graco 25D614 Manuale utente

Task Force Tips

Task Force Tips YE-RF-900 Manuale di programmazione

Shini

Shini SPV-U Series Manuale utente