Cross Technologies 2016-1522 Manuale utente

Instruction Manual

Model 2016-1522#

Downconverter

June 2017, Rev A

EXECUTE

MODEL 2016

CROSS TECHNOLOGIES INC.

F=1544 G=25

ATTEN=10 REF=AUTO-I

REMOTEALARM POWER

DOWNCONVERTER

Data, drawings, and other material contained herein are proprietary to Cross Technologies, Inc.,

but may be reproduced or duplicated without the prior permission of Cross Technologies, Inc.

for purposes of operating the equipment.

When ordering parts from Cross Technologies, Inc., be sure to include the equipment model number,

equipment serial number, and a description of the part.

CROSS TECHNOLOGIES, INC.

6170 Shiloh Road

Alpharetta, Georgia 30005

(770) 886-8005

FAX (770) 886-7964

Toll Free 888-900-5588

WEB www.crosstechnologies.com

E-MAIL [email protected]

INSTRUCTION MANUAL

Model 2016-1522# Downconverter

TABLE OF CONTENTS PAGE

Warranty 2

1.0 General 3

1.1 Equipment Description 3

1.2 Technical Characteristics 4

1.3 Monitor & Control Interface 5

1.4 Environmental Use Information 8

2.0 Installation 9

2.1 Mechanical 9

2.2 Rear Panel Inputs & Outputs 10

2.3 Front Panel Controls & Indicators 11

2.4 Operation 12

2.5 Menu Settings 13

WARRANTY - The following warranty applies to all Cross Technologies, Inc. products.

All Cross Technologies, Inc. products are warranted against defective materials and

workmanship for a period of one year after shipment to customer. Cross Technologies,

Inc.’s obligation under this warranty is limited to repairing or, at Cross Technologies, Inc.’s

option, replacing parts, subassemblies, or entire assemblies. Cross Technologies, Inc. shall

not be liable for any special, indirect, or consequential damages. This warranty does not

cover parts or equipment which have been subject to misuse, negligence, or accident by the

customer during use. All shipping costs for warranty repairs will be prepaid by the

customer. There are not other warranties, express or implied, except as stated herein.

CROSS TECHNOLOGIES, INC.

6170 Shiloh Road

Alpharetta, Georgia 30005

WEB www.crosstechnologies.com

E-MAIL [email protected]

2016-1522# Manual, Rev. 0 Page 2 06/19/17

Model 2016-1522# Downconverter, 1.544 or 2.226 GHz to 70 ± 5 MHz

1.0 General

1.1 Equipment Description

The 2016-1522# Downconverter converts 1.544 or 2.226 GHz to 70 MHz. The gain is 0 to +50 dB, adjustable

in 1±1 dB steps. Push button switches select the input frequency, gain, and other parameters. Front panel LEDs

provide indication of DC power (green), PLL alarm (red), and Remote operation (yellow). Gain is adjustable

manually (MGC) over a 0 to 50 dB range. Remote operation allows selection of frequency and gain. Parameter

selection and frequency and gain settings appear on the LCD display. Connectors are Type N female for the IF

out and RF in and BNC female for the external 10 MHz reference input (Option E) which includes a 10 MHz

output connector which contains either the internal or external 10 MHz reference signal. The unit is powered by

a 100-240 ± 10% VAC power supply, and housed in a 1 3/4” X 19” X 16” rack mount chassis.

EXECUTE

MODEL 2016

CROSS TECHNOLOGIES INC.

F=1544 G=25

ATTEN=10 REF=AUTO-I

REMOTEALARM POWER

DOWNCONVERTER

FRONT PANEL

GND

J10

J18J2

RF IN 10 MHZ REF 10 MHZ

AND

MONITOR EXT REF

CONTROL

OUTPUT INPUT

J20

234 6

789

IF OUT

REAR PANEL (Optional Ethernet Shown)

FIGURE 1.1 Model 2016-1522# Front and Rear Panels

70 ±5

MHz

OUT

RF IN

1.544

and

2.226

GHz

1750 MHz

2870

MHz

3.294

3.976

GHz

1.5 to 2 .3

GHz HP/LP 70 ±5 MHz

CONTROLLER

2016-1522# Downconverter Block Diagram

VAR

ATT EXT

10 M

INT/EXT*

10 M

M&C

* OPTIONAL

FIGURE 1.2 Model 2016-1522# Downconverter Block Diagram

2016-1522# Manual, Rev. 0 Page 3 06/19/17

1.2 Technical Characteristics

TABLE 1.0 2016-1522# Downconverter Specifications*

Input Characteristics

Impedance/Return Loss 50 Ω/12 dB

Frequency 1.544 and 2.226 GHz

Noise Figure, Max. 15 dB at maximum gain

Input Level Range -50 to -20 dBm

Output Characteristics

Impedance/Return Loss 50 Ω/18 dB

Frequency 70 ± 5 MHz

Output Level/max. linear -20 to 0 dBm

Output 1 dB compression +10 dBm maximum gain

Channel Characteristics

Gain at Fc +50 ±3dB maxium, (+50 to 0 dB variable in 1 ±1 dB steps)

Image Rejection > 50 dB, minimum

Frequency Response 1544 or 2226, 10 MHz BW, ± 0.75 dB

Spurious Response <-50 dBc, in band, 70 ± 5 MHz

Group Delay, maximum 0.015 ns/MHz2 parabolic; 0.05 ns/MHz linear; 1 ns ripple

Frequency Sense Non-inverting

Lo Characteristics

LO Step Size NONE, Fixed tuned to 1544 or 2226 MHz In

Frequency Accuracy ±0.01 ppm maximum over temperature internal reference

-110-100-90-80-75

1MHz100kHz10kHz1kHz100Hz

Standard dBC/

(

)

Phase Noise @ F

(

)

Controls, Indicators

Frequency/Gain Selection Direct readout LCD; manual or remote selection

Power; Alarm; Remote Green LED, Red LED, Yellow LED

Remote RS232C, 9600 baud (RS485, Ethernet Optional)

Other RF, IF Connectors N (female), N (female)

10 MHz Connectors BNC (female), 75Ω, works with 50 or 75 ohms (option E)

Alarm, Remote Connector DB9 (female), - NO or NC contact closure on Alarm

Size 19 inch standard chassis 1.75” high X 16.0” deep

Power 100-240 ±10% VAC, 47-63 Hz, 25 watts maximum

*Custom Specifications and/or Standard Options (shown below) included with Model 2016-1522#

Option H - ±0.01 10MHz Internal Reference

Option NN - Connector N-Type (RF), N-Type (IF)

Available Options

E - External 10 MHz Reference

Comm. Interface/Standard RS232

Q - RS485 Remote Interface

W8 - Ethernet; with Web Browser

W18 - Ethernet; with Web Browser & SNMP

W28 - Ethernet; with TCP/IP, Telnet®

Connectors / Impedance

STD - 50ΩType N (RF), 50ΩType N (IF)

SS - 50ΩSMA (RF), 50ΩSMA (IF)

+10˚C to +40˚C; Specifications subject to change without notice.

2016-1522# Manual, Rev. 0 Page 4 06/19/17

1.3 Monitor and Control Interface

A) Remote serial interface

Protocol: RS-232C, 9600 baud rate, no parity, 8 data bits, 1 start bit, and 1 stop bit.

(RS-232C, RS-422, or RS-485 - Option-Q)

Female DB-9

PC Com Port Male DB-9

2015/16/17 M&C Port

M&C Cable Diagram - Cross Technologies Frequency Converters

RX RX

TX TX

DTR

DSR

RTS

CTS

Connector: Rear panel, DB-9 male

J10 Pinouts

(RS-232C/422/485)

Pinouts (RS-232C/422/485)

Pin Function

1 Rx-

2 Rx+ (RS-232C)

3 Tx+ (RS-232C)

4Tx-

5GND

6 Alarm Relay: Common

7 Alarm Relay: Normally Open

8 Not Used

9 Alarm Relay: Normally Closed

2016-1522# Manual, Rev. 0 Page 5 06/19/17

B) Status Requests

Table 1.1 lists the status requests for the 2016-1522# and briefly describes them.

*PLEASE NOTE: The two character {aa}(00-31) prefix, in the table below,

should be used ONLY when RS-485, (OPTION-Q), is selected.

TABLE 1.1 2016-1522# Status

2016-1522# Status Reqquests

TABLE 1.1 2016-1522# Status Requests

Command Syntax* Description

Get Frequency {aaSF} returns {aaSFxxxx}

where: xxxx = frequency in MHz (either 1544 or 2226)

Get Gain {aaSGxx} returns {aaSGxx}

where: xx = gain in dB (00 to 50)

Get reference status {aaSE} returns {aaSExy}

(option E only) where: x = setting:1 for internal 10 MHz; 2 for external 10MHz; 3 for auto detect

y = currently selected in hardware: 1 for internal 10 MHz; 2 for external 10 MHz

Get Reference Insertion Status {aaSL} returns {aaSLx}

(option E only) where: x = 0 for non-insertion; 1 for insertion

Get Output Attenuation {aaSN} returns {aaSNxx}

(option Z20 only) where: xx = output attenuation in dB (00 to 20)

xxx = LNB current in amps to 2 decimal places (e.g., 065 = 0.65 amps)

Get IP address {aaSi} returns {aaSixxx.xxx.xxx.xxx}

(ethernet options only) where xxx.xxx.xxx.xxx = IP address

Get subnet mask {aaSs} returns {aaSsxxx.xxx.xxx.xxx}

(ethernnet options only) where xxx.xxx.xxx.xxx = subnet mask

Get alarm status {aaSA} returns {aaSAa}

where a = alarm state (0 for alarm off; 1 for alarm on)

Get product/model info {aaSV} returns {aaSV2016-1522#xxxxver5.00}

where 2016-1522# = product model

xxx = list of options, if any

"ver" = separates model & options from firmware version

5.00 = firmware version

2016-1522# Manual, Rev. 0 Page 6 06/19/17

C) Commands

Table 1.2 lists the commands for the 2016-1522# and briefly describes them. After a command is sent the

2016-1522# sends a return “>” indicating the command has been received and executed.

General Command Format - The general command format is {aaCND...}, where:

{ = start byte

aa = address (RS-485 only - option -Q)

C = 1 character, either C (command) or S (status)

N = 1 character command or status request

D = 1 character or more of data (depends on command)

} = stop byte

*PLEASE NOTE: The two character {aa}(00-31) prefix, in the table below,

should be used ONLY when RS-485, (OPTION-Q), is selected.

Table 1.2 2016-1522# Commaands

Commands

Table 1.2 2016-1522# Commands

Command Syntax* Description

Set Frequency {aaCFx} where: x = 0 for 1544 MHz: x = 1 for 2226 MHz

Set Gain {aaCGxx} where: xx = gain (Range: 00 to 50) in 1 dB steps

10 MHz reference mode {aaCEx} where: x = 0 for internal 10 MHz;1 for external 10 MHz;

(option E only) 2 for auto detect

Reference insertion on output {aaCLx} where: x = 0 for non-insertion; 1 for insertion

(option E only)

Set Output Attenuation {aaCNxx} where: xx = attenuation (Range 00 to 20) in 1 dB steps

(option Z20 only)

2016-1522# Manual, Rev. 0 Page 7 06/19/17

1.4 Use Information

A.Rack-Mounting - To mount this equipment in a rack, please refer to the installation instructions

located in the user manual furnished by the manufacturer of your equipment rack.

B. Mechanical loading - Mounting of equipment in a rack should be such that a hazardous condition

does not exist due to uneven weight distribution.

C.Elevated operating ambient temperature - If installed in a closed or multi-unit rack assembly,

the operating ambient temperature of the rack may be greater than room ambient temperature.

Therefore, consideration should be given to Tmra (Maximum Recommended Ambient Temperature).

D. Reduced air flow - Installation of the equipment in a rack should be such that the amount of air flow

required for safe operation of the equipment is not compromised. Additional space between unit

may be required.

E. Circuit Overloading - Consideration should be given to the connection of the equipment to the supply

circuit and the effect that overloading of circuits could have on over current protection and supply wiring.

Appropriate consideration of equipment name plate rating should be used, when addressing this concern.

F. Reliable Earthing - Reliable earthing of rack-mounted equipment should be maintained. Particular

attention should be given to supply connections other than direct connection to the Branch

(use of power strips).

G. Top Cover - There are no serviceable parts inside the product so, the Top Cover should not be removed.

If the Top Cover is removed the ground strap and associated screw MUST BE REINSTALLED

prior to Top Cover screw replacement. FAILURE TO DO this may cause INGRESS and/or EGRESS

emission problems.

2016-1522# Manual, Rev. 0 Page 8 06/19/17

2.0 Installation

2.1 Mechanical

The 2016-1522# consists of one RF/Controller PCB housed in a 1 RU (1 3/4 inch high) by 16 inch deep chassis.

A switching, ±12, +24, +5 VDC power supply provides power for the assemblies. The 2016-1522# can be

secured to a rack using the 4 holes on the front panel. Figure 2.1 shows how the 2016-1522# is assembled.

POWER

SUPPLY

FIGURE 2.1 2016-1522# Mechanical Assembly

2016-1522# Manual, Rev. 0 Page 9 06/19/17

2.2 Rear Panel Input/Output Signals

Figure 2.2 shows the input and output connectors on the rear panel.

GND

J10

J18J1

IF OUT 10 MHZ REF 10 MHZ

AND

MONITOR EXT REF

CONTROL

OUTPUT INPUT

J20

234 6

789

AC1 - POWER IN

AC input for switching power

supply. 100-240 ±10% VAC,

47-60 Hz.

J2 - RF IN

-50 to -20 dBm input

1.544 & 2.226 GHz

see Table 2.2.

J10 - MONITOR AND CONTROL

DB9 female connector

see Table 2.1

J20 - Ethernet Connection

RJ45 Ethernet Connector

J18 - 10 MHz REF OUTPUT (option -E)

10 MHz external reference output

3 ± 3 dBm, 75Ω, BNC female connector.

J3 - 10 MHz EXT REF INPUT (Option -E)

10 MHz external reference input

3 ± 3 dBm, 75Ω, BNC female connector.

J1 - IF OUT

-20 to 0 MHz output

70 ±5 MHz dBm

see Table 2.2.

RF IN

FIGURE 2.2 2016-1522# Rear Panel I/Os

TABLE 2.1 J110

2.1 J10 Pinouts (RS-232C*)

Pin Function

1 Not Used

2 Rx+ (RS-232C)

3 Tx+ (RS-232C)

4 Not Used

5GND

6 Alarm Relay: Common

7 Alarm Relay: Normally Closed

8 Not Used

9 Alarm Relay: Normally Open

*Remote Serial Interface

Interface: DB-9 Male

Protocol: RS-232C, 9600 baud rate, no parity, 8 data bits, 1 start bit, 1 stop bit

TABLE 2.2 IFF/RF

2.2 IF/RF Connector Options

Options

Option IF RF

STD BNC, 75ΩType F, 75Ω

B BNC, 75ΩBNC, 75Ω

C BNC, 75ΩBNC, 50Ω

D BNC, 50ΩBNC, 50Ω

F Type F, 75 ΩType F, 75 Ω

FN Type F, 75 ΩType N, 50 Ω

J BNC, 50ΩType F, 75 Ω

K BNC, 50ΩBNC, 75 Ω

M BNC, 50ΩType N, 50Ω

N BNC, 75ΩType N, 50Ω

S BNC, 50ΩSMA, 50Ω

2016-1522# Manual, Rev. 0 Page 10 06/19/17

Indice

Altri manuali Cross Technologies Convertitore multimediale

Cross Technologies

Cross Technologies 2016-95 Manuale utente

Cross Technologies

Cross Technologies 2016-75-213 Manuale utente

Cross Technologies

Cross Technologies 2016-02-1200 Manuale utente

Cross Technologies

Cross Technologies 2015-123 Manuale utente

Cross Technologies

Cross Technologies 2117-7172 Manuale utente

Cross Technologies

Cross Technologies 2016-25 Manuale utente

Cross Technologies

Cross Technologies 3116-7786-2150 Manuale utente

Cross Technologies

Cross Technologies 2016-8085 Manuale utente

Cross Technologies

Cross Technologies 2416 02I Series Manuale utente

Cross Technologies

Cross Technologies 3115-21-109 Manuale utente

Cross Technologies

Cross Technologies 2415 0925 Series Manuale utente

Cross Technologies

Cross Technologies 4115-41-212 Manuale utente

Cross Technologies

Cross Technologies 2005-10 Manuale utente

Cross Technologies

Cross Technologies 4116-31-2831 Manuale utente

Cross Technologies

Cross Technologies 2117-8485 Manuale utente

Cross Technologies

Cross Technologies 2016-03A Manuale utente

Cross Technologies

Cross Technologies 2015-7075 Manuale utente

Cross Technologies

Cross Technologies 2415-02 Series Manuale utente

Cross Technologies

Cross Technologies 2017-0923 370 Series Manuale utente

Cross Technologies

Cross Technologies 2099-2424 Manuale utente

Cross Technologies

Cross Technologies 2015-58T Manuale utente

Cross Technologies

Cross Technologies 2017-14 Manuale utente

Cross Technologies

Cross Technologies 2416-x02 Manuale utente

Cross Technologies

Cross Technologies 2416 25 Series Manuale utente

Manuali Convertitore multimediale popolari di altre marche

SoundTraxx

SoundTraxx Blunami BLU-2200 Manuale utente

SPROLINK

SPROLINK VA1 Manuale utente

Acclaim Lighting

Acclaim Lighting DDC-1-AC Manuale utente

Nikon

Nikon AF-S TC-20E III Manuale utente

Axis

Axis AXIS Q7406 Manuale utente

Omega

Omega TAC80B-J Manuale utente

Zoom

Zoom Thunderbolt TAC-2R Manuale utente

OST

OST iConverter 10/100M Manuale utente

Vertiv

Vertiv Netsure Manuale utente

birddog

birddog MINI Manuale utente

Roland

Roland GI-10 Manuale utente

Wallenstein

Wallenstein WX310 Manuale utente

Pace

Pace MSS 200-1 Manuale utente

Solar Converters

Solar Converters EQ 12/24-50 Manuale utente

CYP

CYP EL-7400V Manuale utente

TIE

TIE MIDI 1i1o Manuale utente

DCS

DCS Vivaldi Upsampler Manuale utente

Westermo

Westermo MCW-211 SERIES Manuale utente