Crystal Vision Flip HD Manuale utente
Crystal Vision Ltd., Lion Technology Park, Station Road East, Whittlesford, Cambridge, CB22 4WL, England.
E-mail: [email protected] Website: www.crystalvision.tv Tel: +44(0) 1223 497049 Fax: +44(0) 1223 497059
Flip HD
HD/SD scan reverser
Flip HD User Manual R1.1 Crystal Vision
Flip HD User Manual R1.1 116/04/2007
Contents
1 Introduction 3
2 Hardware installation 4
2.1 Rear modules and signal I/O 4
Rear module connections with RM34 4
Rear module connections with RM29 5
2.2 Module configuration 5
3 Card edge operation 6
3.1 Card edge controls 6
3.2 Reading card edge LEDs 6
3.3 Card edge switch settings 7
Return to default values 7
Engineering menu 7
4 Using the front control panel 8
4.1 Module selected 8
Updating the display 10
4.2 The Flip HD active panel menu structure 10
Flip HD Menu Structure 11
Reset (factory defaults) 11
Status 12
5 Statesman 13
5.1 Statesman operation 13
Input status 14
Flip 14
Flip HD User Manual R1.1 Crystal Vision
Flip HD User Manual R1.1 216/04/2007
Reset (factory defaults) 14
6 Trouble shooting 15
6.1 Card edge status LEDs 15
Basic fault finding guide 15
7 Specification 16
Revision 1 RM34 information added 16/04/07
Flip HD User Manual R1.1 Crystal Vision
Flip HD User Manual R1.1 316/04/2007
1Introduction
Flip HD is an HD/SD scan reverser, which produces a reverse image idea for studio floor
monitor applications. DA outputs are available for both the reclocked input and converted
programme.
Flip HD block diagram
The main features are as follows:
•Reversed output image with bypass
•One frame video delay in all modes
•Two scaled outputs and two input loop-throughs
•Fits in standard frames alongside HD, SD and audio products
Flip HD is a 100mm x 266mm module, which fits in the four standard frames and can be
integrated with any boards from the company’s full product range. It uses the RM34 rear
connector.
Flip HD User Manual R1.1 Crystal Vision
Flip HD User Manual R1.1 416/04/2007
2Hardware installation
The Flip HD single height module uses the RM34 rear connector that will fit into all
Crystal Vision rack frames. All modules can be plugged in and removed while the frame
is powered without damage.
2.1 Rear modules and signal I/O
The 4U Indigo 4 frame will house up to 24 single height modules with up to three power
supplies. The 2U Indigo 2 frame will house up to 12 single height modules and dual
power supplies. The 1U Indigo 1 frame will house six single height modules and a single
power supply. The Indigo DT desktop boxes have a built-in power supply and will house
up to two single height modules.
Note: For details of fitting rear connectors please refer to the appropriate frame manual.
Rear module connections with RM34
The RM34 being a single height module will allow maximum packing density with the
maximum number of outputs available.
RM34 rear module connector Description
RM34
•24 Flip HD modules per
Indigo 4 frame
•12 per Indigo 2
•Six per Indigo 1 frame
•2 per Indigo DT
•All frame slots can be
used
BNC I/O assignment
HD/SD OUT Processed Serial Digital Output
HD/SD OUT Processed Serial Digital Output
HD/SD IN LOOP OUT High Definition / Standard Definition Serial Digital Input reclocked loop-through
HD/SD IN LOOP OUT High Definition / Standard Definition Serial Digital Input reclocked loop-through
NC No user connection
HD/SD INPUT High Definition / Standard Definition Serial Digital Input
Flip HD User Manual R1.1 Crystal Vision
Flip HD User Manual R1.1 516/04/2007
Rear module connections with RM29
The RM29 can also be used with the Flip HD but is not available for new installations. It
is also a single height module allowing maximum packing density with the maximum
number of outputs available.
RM29 rear module connector Description
RM29
•24 Flip HD modules per
Indigo 4 frame
•12 per Indigo 2
•Six per Indigo 1 frame
•2 per Indigo DT
•All frame slots can be
used
BNC I/O assignment
HD/SD OUT Processed Serial Digital Output
HD/SD OUT Processed Serial Digital Output
HD/SD IN LOOP OUT High Definition / Standard Definition Serial Digital Input reclocked loop-through
HD/SD IN LOOP OUT High Definition / Standard Definition Serial Digital Input reclocked loop-through
HD/SD IN High Definition / Standard Definition Serial Digital Input
2.2 Module configuration
There are no user re-configurable jumper links on the Flip HD.
Flip HD User Manual R1.1 Crystal Vision
Flip HD User Manual R1.1 616/04/2007
3Card edge operation
3.1 Card edge controls
Once the start-up initialisation procedure is complete, the Flip HD card can be controlled
or configured from the card edge, the active control panel or the Statesman PC interface.
This chapter will concentrate on the card edge controls.
The front edge of the card provides power rail monitoring, menu selection, variables
adjustment and a ten-digit visual status display.
Flip HD front edge view
The Menu piano switch is used to select any the main menus, whilst the [SEL] rotary hex
switch selects sub-menus. The [ADJ] shaft encoder is used to select an option within a
menu or sub menu.
3.2 Reading card edge LEDs
Card edge LEDs may be used in conjunction with status information from any connected
remote status panel display or from Statesman if available.
Refer also to the trouble shooting chapter for more help with solving problems and
monitoring status information.
The following table summarises the card edge LED functions and colours:
Name LED
Colour Function when ON Function when Off
HD Yellow Video input standard is HD
(High Definition)
SD Yellow Video input standard is SD
(Standard Definition)
Input not present
PSU Green Good power supply (PSU) rails One or more of the monitor
supplies is out of specification
Flip HD User Manual R1.1 Crystal Vision
Flip HD User Manual R1.1 716/04/2007
3.3 Card edge switch settings
The 8-way piano switch allows control options to be selected.
Lever Function Action
All UP Flip HD
1 Down Not used No function assigned.
2 Down Output Select Flip/Bypass select.
3 Down Reset Reset to defaults.
4 Down Not Used No function assigned.
5 Down Not used No function assigned.
6 Down Status Input standard and engineering information.
7 Down Not used No function assigned.
8 Down Not used No function assigned.
Return to default values
Menu piano lever 3 DOWN, all others in the UP position:-
SEL
No. Menu Function and card edge display examples
0 Reset Rotate [ADJ] to return all values to their default
1-F Not used No function assigned.
Parameter Default value
Flip/Bypass Bypass.
Engineering menu
Menu piano lever 6 DOWN, all others in the UP position:-
SEL
No. Menu Function and card edge display examples
0 Input
Standard Shows the auto detected input video standard.
Example: 525 i 59
1 Software Shows the version level of the currently fitted software.
2 Serial number Shows the electronically stored six-digit serial number.
Example 643231
Flip HD User Manual R1.1 Crystal Vision
Flip HD User Manual R1.1 816/04/2007
4Using the front control panel
4.1 Module selected
This operational guide assumes that the panel has been set up according to the Panel setup
procedure described in the Crystal Vision Control Panel manual.
Note: It is ESSENTIAL that the Panel setup procedure is followed and any old or unknown
passwords cleared prior to using the panel for the first time.
At power up, the two line 20-character screen will display ‘Crystal Vision’ followed by
the firmware version number for the control panel. All eight control panel keys LEDs will
illuminate.
The Crystal Vision control panel start up display
'Control Panel' then briefly replaces the version number display.
If the control panel firmware has been updated for Statesman control (version 1.5.0 or
higher), Statesman Mode will be entered and the message, ‘Press CAL to Exit’ will be
displayed and the CAL LED will light.
Statesman mode is entered by default
Flip HD User Manual R1.1 Crystal Vision
Flip HD User Manual R1.1 916/04/2007
To continue with control panel operation or configuration, press the CAL key once. A
second press of the CAL key will return to Statesman control.
The control panel will display the name of the card that first responds to the polling
request together with its location number.
The location number consists of the frame number plus the card position in the frame.
Navigating the display
The functions assigned to control panel keys are:
•DEVICE – enters Device menu to select a card or show cards available / enters Panel
setup when held down during power up / shows frame status when pressed from
Statesman mode
•CAL – enters or leaves Statesman mode / enters panel diagnostics mode when held down
during power up / updates the display
•Asterisk – enters board rename menu from the Device menu
•F1 to F4 – soft keys, function assigned within each menu
•HOME – moves the display to the home menu
•ENTER – accept current selection
•Upward arrow – used to move up the menu structure / enter lock panel menu from the
Device menu
•Rotary control – shaft encoder used to select options or variable data
Note: Please refer to the Crystal Vision Control Panel manual for details of the Panel Setup, Lock Panel and
Diagnostic menus.
Selecting Flip HD
To select a particular card in a frame, press the DEVICE key to go to the Device menu.
Note, there may be a delay whilst the frame is interrogated during which time the ‘No
cards Found’ could be displayed.
The top line of the display will show ‘Available Cards X’, where X is the number of cards
that have responded so far to the polling request.
The available cards menu
Rotate the shaft encoder and the bottom row will display the successfully polled cards by
name and location or slot number.
In the example above, the card displayed is located in the first frame in slot number 3.
When the desired card is selected press the ENTER key to access that card’s HOME
menu. The message shows that an Flip HD has been selected.
Indice
Altri manuali Crystal Vision Unità di controllo
Manuali Unità di controllo popolari di altre marche
Festo
Festo Compact Performance CP-FB6-E Manuale elenco delle parti
Elo TouchSystems
Elo TouchSystems DMS-SA19P-EXTME Manuale utente
JS Automation
JS Automation MPC3034A Manuale utente
JAUDT
JAUDT SW GII 6406 Series Guida rapida
Spektrum
Spektrum Air Module System Manuale utente
BOC Edwards
BOC Edwards Q Series Manuale utente
