CTA AUT-VDMC Manuale utente
Vehicle Dash Mount w/ Custom Flex Arms
AUT-VDMC
INSTALLATION - MANUAL
INSTALLATION:
1.Installing the Mount to Vehicle :
1A. Drill holes on the surface as shown above
with power drill tool (not provided).
1B. Place vehicle dash mount (B) aligning the holes
drilled on surface and then screw in the provided x4
screws (C) through the base with a screw driver (not
provided) until securely tightened.
A
A
CONTENTS:
x4 Screws
C
x3
Foam
Pads
B
1mm
5mm
10mm
x1
Vehicle
Dash Mount
A
Drilling into the dash, wall, or roof will be a permanent installation and may cause damage if not
installed properly. Use caution and consult a mobile install professional to avoid drilling into the gas
tank,electrical system or other highly sensitive vehicle components.
2.Attaching Foam Pad to Tablet Holder :
3. Inserting Tablet to Holder :
4. Adjustability
A
B
3A. Press quick release button on side of tablet
holder (A) to release the adjustable end.
3B. Insert tablet corner against the spring arm. Push adjustable arm
down against opposite corner (A). Be sure it is as snug as possible.
1.Twist the screw knobs
counter clock-wise to loosen
joints
2. Adjust the arm to desired position
then twist the screw knob clock-wise
until securely tightened.
2A. Select the appropiate foam pad (B) according to the thickness of your tablet (or tablet in its case), then
press adhesive side into center of the tablet holder.
1mm
5mm
10mm
Please be sure to fasten all the screws were
tightened securely while using the stand.
Not for use while driving.
Max loading :1KG
Do not install CTA’s products over an air bag
cover or within the air bag deployment zone.
CTA Digital, Inc. assumes no respons of liability
for injury or death as a result of car crashes and
/ or air bag deployment. CTA is not responsible
for any damages caused to your vehicle, your
device, or yourself due to the installation or use
of this product.
Caution
Safety Precautions
- Use this table to determine the appropiate
foam pad (B) to use with your tablet.
Note: sizes refer to total tablet size with or
without a case
Tablet Thickness:
Foam Pad
Thickness:
1mm 0.67-1.06in / 17-27mm
0.51- 0.91in / 13-23mm
0.31- 0.71in / 8-18mm
5mm
10mm
A
**Tablet for illustration
only and not included
A
A
Indice
Altri manuali CTA Rack e supporto
CTA
CTA PAD-CHKBM10 Manuale utente
CTA
CTA PAD-FTSU Manuale utente
CTA
CTA PAD-TAM Manuale utente
CTA
CTA PAD-KMS Manuale utente
CTA
CTA PAD-ASK13B Manuale utente
CTA
CTA PAD-ADMA Manuale utente
CTA
CTA ADD-FS2VDMB Manuale utente
CTA
CTA PAD-MSPC10 Series Manuale utente
CTA
CTA PAD-PARAF1 Manuale utente
CTA
CTA PAD-CHKWDC Manuale utente
CTA
CTA PAD-PF1ICC Manuale utente
CTA
CTA PAD-PARAPOSW Manuale utente
CTA
CTA PAD-UGT Manuale utente
CTA
CTA PAD-CHKWM10 Manuale utente
CTA
CTA PAD-VPOS1W Manuale utente
CTA
CTA PAD-HSKSBAE Manuale utente
CTA
CTA PAD-UAM Manuale utente
CTA
CTA ADD-PARAFS Manuale utente
CTA
CTA PAD-WDM Manuale utente
CTA
CTA PAD-ASKP Manuale utente
