Custom Audio Electronics PRT 80 Manuale utente

PRT 80

Thermal printer for information kiosks and

ATMs

PRT 80

UserManual

www.custom.it

PRT 80

means, is forbidden. While guaranteeing that the information contained in it has been carefully checked, CUSTOM

ENGINEERING SPA and other entities utilized in the realization of this manual bear no responsibility for how the

manual is used.

Information regarding any errors found in it or suggestions on how it could be improved are appreciated. Since

products are subject to continuous check and improvement, CUSTOM ENGINEERING SPA reserves the right to

make changes in information contained in this manual without prior notification.

COD. DOME-PRT80 REV. 1.00

CUSTOM ENGINEERING SPA

Str. Berettine 2 - 43010 Fontevivo (PARMA) - Italy

Tel.: +39 0521-680111 - Fax: +39 0521-610701

http: www.custom.it

Customer Service Department:

OEM AREA : Tel.: +39 059 88 69 587

Email: [email protected]

PRT 80

PRINTER COMPONENTS

A. TPL825-S Front external view

1- Rewinder

2- Printer frame

3- ”Near paper end” led

4- Status led

5- “Power on” led

6- “Form Feed” Key

7- “Line Feed” Key

8- Paper roll support

9- Printing mechanism

10- Near paper end sensor

11- Paper roll

PRT 80

B. Rear external view with RS232 serial interface

1-Paper insert

2-Power supply connector

3-RS232 serial connector

TABLE OF CONTENTS

PRT 80

INTRODUCTION

MANUAL CONTENTS ...................................................................................................................................... 1

EXPLANATORY NOTES USED IN THIS MANUAL ........................................................................................... 1

GENERAL SAFETY INFORMATION ................................................................................................................ 1

UNPAKING THE PRINTER .............................................................................................................................. 2

PRINTER FEATURES ..................................................................................................................................... 2

PRINTER DESCRIPTION ............................................................................................................................... 3

1. INSTALLATIONAND USE

1.1 CONNECTIONS ...................................................................................................................................... 1-1

1.1.1 Power Supply .................................................................................................................................. 1-1

1.2 SELF-TEST ............................................................................................................................................. 1-1

1.3 CONFIGURATION .................................................................................................................................. 1-2

1.4 HEXADECIMAL DUMP ............................................................................................................................ 1-3

1.5 MAINTENANCE ....................................................................................................................................... 1-3

1.5.1 Changing the paper roll ................................................................................................................... 1-3

2.INTERFACES

2.1 RS232 SERIAL ....................................................................................................................................... 2-1

3. PRINTER FUNCTIONS

3.1 PRINTER DIRECTION ........................................................................................................................... 3-1

3.2 COMMANDS DESCRIPTION ................................................................................................................. 3-2

3.2.1 Custom TPT emulation ................................................................................................................... 3-2

3.2.2 ESC/POS emulation ..................................................................................................................... 3-33

4. TECHNICAL SPECIFICATIONS

4.1 TECHNICAL SPECIFICATIONS .............................................................................................................. 4-1

4.2 DIMENSIONS ......................................................................................................................................... 4-3

5.CHARACTERSETS

5.1 CHARACTER SETS ............................................................................................................................... 5-1

A.APPENDIXA -ACCESSORIESAND SPARE PARTS

A.1 ACCESSORIES ..................................................................................................................................... A-1

A.1.1 Power supply .................................................................................................................................. A-1

A.2 SPARE PARTS ....................................................................................................................................... A-2

TABLE OF CONTENTS

PRT 80

Blank Page

INTRODUCTION

PRT 801

MANUALCONTENTS

In addition to the Introduction which includes a description of the explanatory notes used in the manual,

general safety information, how to unpack the printer and a brief description of the printer including its basic

features, this manual is organized as follows:

Chapter 1: Contains the information required for correct printer installation and its proper use

Chapter 2: Contains information on interface specifications

Chapter 3: Contains a description of the printer command set

Chapter 4: Contains Technical Specifications of the printer

Chapter 5: Contains the character sets (fonts) used by the printer

EXPLANATORYNOTES USED INTHIS MANUAL

N.B.

Gives important information or suggestions relative to the use of the printer.

WARNING

Information marked with this symbol must be carefully followed to guard against damaging the

printer.

DANGER

Information marked with this symbol must be carefully followed to guard against operator injury or

damage.

GENERALSAFETYINFORMATION

•Read and keep the instructions which follow.

•Follow all warnings and instructions indicated on the printer.

•Before cleaning the printer, disconnect the power supply.

•Clean the printer with a damp cloth. Do not use liquid or spray products.

•Do not operate the printer near water.

•Do not use the printer on unstable surfaces that might cause it to fall and be seriously damaged.

•Only use the printer on hard surfaces and in environments that guarantee proper ventilation.

•Make sure the printer is placed in such a way as to avoid damage to its wiring.

•Use the type of electrical power supply indicated on the printer label. If in doubt, contact your retailer.

•Do not block the ventilation openings.

•Do not introduce foreign objects of any kind into the printer as this could cause a short circuit or damage

parts that could jeopardize printer functioning.

•Do not spill liquids onto the printer.

•Do not carry out technical operations on the printer, with the exception of the scheduled maintenance

procedures specifically indicated in the user manual.

•Disconnect the printer from the electricity supply and have it repaired by a specialized technician when:

A. The feed connector has been damaged.

B. Liquid has seeped inside the printer.

C. The printer has been exposed to rain or water.

D. The printer is not functioning normally despite the fact that all instructions in the users manual

have been followed.

E. The printer has been dropped and its outer casing damaged.

F. Printer performance is poor.

G. The printer is not functioning.UNPACKING THE PRINTER

INTRODUCTION

PRT 80 2

UNPACKING THE PRINTER

Remove the printer from its carton being careful not to damage the packing material so that it may be re-used

if the printer is to be transported in the future.

Make sure that all the components listed below are present and that there are no signs of damage. If there

are, contact Customer Service.

1. Upper foam packing shell

2. Paper roll

3. Manual (or CD-Rom)

4. Paper adaptation stirrup for 80mm.

5. Printer

6. Lower foam packing shell

7. Box

PRINTER FEATURES

The printer is comprised of printers designed to emit high-resolution thermal-printed tickets ideal for use in

information and multimedia kiosks, self-service machines, no-queue systems, parking areas, gaming

machines and toll receipt machines.

The printer offers a wide range of options in addition to normal print features:

•Ticket width : 80 mm.

•High speed printing: 130mm/sec.

•Interfaces : RS232

•ESC/POSand CUSTOM TPT emulation.

•Bar code UPC-A. UPC-E, EAN13, EAN8, CODE39, ITF, CODABAR, CODE93, CODE128 and

CODE32.

•6 standard and international character set fonts.

INTRODUCTION

PRT 803

•Completely- or partially-programmable fonts.

•Double width/height, quadruple width/height, expanded, italic, rotated 90°, 180° and 270°.

•Receive buffer: 16Kbytes.

•Definition of function macros for automatic operation repetition.

•Internal programmable counter.

•Graphic print mode.

•Print density.

•ESC/POSEmulation :6 programmable logos 640 x 215 each dots

CUSTOM TPT Emulation :3 programmable logos: 640 x 431 each dots

•Near paper end sensors.

PRINTER DESCRIPTION

The printer (fig.1) is comprised of a metal frame (7), paper roll holder (9), printing mechanism (8) and

rewinder (1).

The following keys are located on the control panel: FORM FEED (5), LINE FEED (6), “Power On” LED (4),

Near paper end LED (3) and “Status” LED (2).

•When the LINE FEED (6) key is pressed, the printer advances the paper so that it may be inserted

manually in the printing mechanism. During power-up, if the LINE FEED key is held down, the printer will

perform the FONT TEST routine.

•If the FORM FEED (5) key is enabled, when it is pressed the printer advances the paper the number of

increments programmed in the Eeprom. If the FORM FEED key is not enabled and the printer is in Custom

Emulation mode, when the key is pressed, the code 12 (HEX 0C) is transmitted on the RS232 serial line. This

function may be modified by the ESC = software command (see section on software commands).

•During power-up, if both keys are held down, the printer enters the print setup routine. Following the print-

out of the setup report, the printer remains in standby until a key is pressed or signals arrive from the serial

port; each 10 characters it prints out hexadecimal and ASCII codes (if the characters are underlined, the

receive buffer is full); see Receive buffer hexidecimal print-out.

(Fig.1)

INTRODUCTION

PRT 80 4

(Tab.1)

sutatsDELnoitpircseD

ydaetSNOretnirP- noitcnuflamon

gniknilbdipaRgnitaehrevO

gniknilbwolS( doirepdednetxeroftil) egassem"repaPoN"

gniknilbwolS( )doireptrohsroftilsdrawpudenrutdaeH

ffosniameRnoitcnuflamretnirP

•The “Power On” LED (green) indicates that the printer is on.

•The “Near paper end” LED (red) indicates that the paper is about to run out.

•The “Status” LED (yellow) indicates printer status; the check is made on-line. Given in the table below are

the various LED signals and the corresponding printer status.

Indice

Altri manuali Custom Audio Electronics Stampante

Custom Audio Electronics

Custom Audio Electronics KPM216HIII Manuale utente

Custom Audio Electronics

Custom Audio Electronics CMxxx Manuale utente

Custom Audio Electronics

Custom Audio Electronics TM-U925 Manuale utente

Custom Audio Electronics

Custom Audio Electronics MY3 X Istruzioni per l'installazione

Custom Audio Electronics

Custom Audio Electronics KPM216HII-ETH Manuale utente

Custom Audio Electronics

Custom Audio Electronics TPT60H Manuale utente

Custom Audio Electronics

Custom Audio Electronics TK180 Supplemento

Custom Audio Electronics

Custom Audio Electronics VK80 Manuale utente

Custom Audio Electronics

Custom Audio Electronics SILVER Manuale utente

Custom Audio Electronics

Custom Audio Electronics DP24-40 H Manuale utente

Custom Audio Electronics

Custom Audio Electronics Kube Scanner 120 Manuale utente

Custom Audio Electronics

Custom Audio Electronics MODUS3 Manuale utente

Custom Audio Electronics

Custom Audio Electronics STIMARE STIMA-SML Manuale utente

Custom Audio Electronics

Custom Audio Electronics Custom Manuale utente

Custom Audio Electronics

Custom Audio Electronics KPM302III Manuale utente

Custom Audio Electronics

Custom Audio Electronics KPM 216 H Manuale utente

Custom Audio Electronics

Custom Audio Electronics KPM180H Manuale utente

Custom Audio Electronics

Custom Audio Electronics MT2460 Manuale utente

Custom Audio Electronics

Custom Audio Electronics VKP80II-SX Manuale utente

Custom Audio Electronics

Custom Audio Electronics SMICE-PS Manuale utente

Custom Audio Electronics

Custom Audio Electronics Kube II Manuale utente

Custom Audio Electronics

Custom Audio Electronics Plus II Manuale utente

Custom Audio Electronics

Custom Audio Electronics K-80 Istruzioni per l'installazione

Custom Audio Electronics

Custom Audio Electronics B202HIII Supplemento

Manuali Stampante popolari di altre marche

Lexmark

Lexmark 1400 Series Manuale

Canon

Canon i70 Series Manuale utente

Evolis

Evolis Elypso Manuale utente

Kyocera

Kyocera FS-9530DN Manuale utente

Canon

Canon LASER SHOT LBP-1210 Manuale utente

Samsung

Samsung BIXOLON SRP-350plusF Manuale utente

Canon

Canon PIXMA PRO-1 Series Manuale utente

Canon

Canon PIXMA G3560 Guida all'installazione

Dell

Dell Color Laser Printer 2130cn Manuale utente

Tektronix

Tektronix Phaser 840 Manuale utente

Epson

Epson ET-7750 Istruzioni operative

Canon

Canon CLBR 460ps Manuale utente

Eltron

Eltron P210 Guide Manuale utente

Ricoh

Ricoh MD-P1 Manuale utente

Epson

Epson SC-F7100 series Manuale utente

Epson

Epson Stylus C40UX Manuale utente

Canon

Canon imagePASS-A2 Manuale utente

Canon

Canon S820D Manuale utente