D-Link DCS-1000 Manuale

Using the DCS-1000/DCS-1000W IP Camera

as a Security System

D-Link’s IP Camera System is one of the most cost

effect security solutions today. Both the DCS-1000

Wired model and DCS-1000W Wired/Wireless model

have input/output controls for interfacing with security

systems.

On the back of the Camera you will find an 8-position

connector. This connector has 2 input triggers for

security sensors and 2 output triggers for security

alarms.

Security sensors for input are available as Passive (low-

current/low voltage) sensors or Active (powered)

sensors.

Because of power limitations of the DCS cameras and

its compatibility with Power over Ethernet standards the

sensor power requirement must be obeyed for proper operation. We have listed Passive and

Active components that will interface with the DCS family of Cameras. Passive components must

not exceed 5V 100mA. Active components must be self-powered by an external power source.

For the demonstration below a D-Link DCS-1000 was purchased from www.dlinkshop.com , the

security equipment was purchased from www.smarthome.com, and some cable accessories from

a local hardware store.

Materials

•DCS-1000

•2 Ethernet Cables & Ethernet Switch/Internet Router

•An Ethernet based PC to configure system

•Internet Name Server and E-Mail Server to send capture information

•10FT. 24Gauge

•1 light current power distribution block for 12V power

•30W Weatherproof Siren

•High Sensitivity DPDT relay (allows 5V camera to turn on 12V siren)

•Mini-Magnetic Contact Switch (commonly used for doors or windows)

•PIR Motion Detector

You will need some simple tools like wire cutters/strippers and the appropriate screwdriver for

mounting and distribution block setup.

Everything less the camera cost about $97 US Dollars including shipping.

Basic Hardware Set-up Diagram

The diagram below shows the hardware configuration for 1 Active Sensor (PIR Motion Sensor), 1

Passive Sensor (Magnetic Switch), and 1 output (For Relay) for a siren.

Passive Component Notes!!!

Only simple magnetic or contact switches can be used for Passive components. This limitation is

by the camera only supplying 5V and less then 100mA current to those circuits. Distance for

passive components is limited by a viewable camera range of about 25 Ft using 26GA wire.

Active Component Notes!!!

A separate power supply is needed for these devices. In order to choose the proper PS. The total

current draw by all the components cannot exceed the Max supplied by the power supply.

Example

Our PIR Motion Detector = 17 mA = .017A

Our Relay = 60 mA = .06A

Siren = 200mA = .20A

Total : .277A

Purchased DC power adapter 12V DC 1.2A Max to cover all Active Sensors and Siren, with room

to grow.

Camera Configuration

Follow the instructions for setting up the camera either wired/wireless. If this is a home and the

camera is behind an Internet router additional set-up notes for you router can be found on

www.dlink.com.

Once logged into the camera on the main menu click/select trigger and the following screen will

appear.

These fields control Input Trigger 1 and Trigger 2. Each Input trigger can trigger either or both

Output triggers.

SMTP Server Address:Name or IP address of a Mail Server that camera can use to send.

Sender E-Mail: Name of the Camera who sent the mail

Receiver E-Mail: Name of person to receive pictures when sensors are activated

Sending Interval: The time between additional sequences ofpictures are taken when sensors activated

Sending Times: The number of times the camera takes additional sequences of pictures based on Sending Interval.

Trigger I/O: Enable Output trigger for the specified input trigger

Output # Time: How long the output trigger is activated if Sensor is activated. (ie. How long should siren ring?)

INPUT TRIGGER RESPONSE NOTES!!!

The camera will take a sequence of pictures and the output trigger is activated when there is a

change open or close of the sensor. Example: The magnetic switch is opened, a sequence is

sent and siren goes off. The switch is then closed, an additional sequence is sent and the alarm

goes off. The camera is designed this way so if there is an intrusion, the intrusion is detect if

intruder simply opens then closes the entrance.

Additional Component Listing for use with DCS-1000/DCS-1000W

All components listed below can be found and www.smarthome.com

Passive Components

Glass Break Sensor PN: 5150w –Sentrol Inc.

Any contact switch or pressure switch not exceeding 100mW current draw

Examples @ http://www.smarthome.com/seccontacts.html

Active Components

Coral Plus Temperature Compensated PIR Detector –Visonic Ltd.

Duet Dual Microwave/IR Motion Detector –Visonic Ltd.

Bravo 6 Dual PIR Detector –DSC Security Products

Any active security sensor that uses external power and a separate normally closed N/C circuit

for detection: examples on http://www.smarthome.com/secpirmotion.html

Power and Relay Components

ELK Products Inc. ELK-924 Single 12V to 120V relay switch

DVE Power Supply 12V 1.2A

More can be found on http://www.smarthome.com/powersupply.html

Alarm Components

Universal SS30 30W 8Ohm Siren

More visual and audible alarms can be found at examples @ http://www.smarthome.com

Altri manuali per DCS-1000

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali D-Link Telecamera IP

D-Link

D-Link DCS-2800LH-EU Manuale utente

D-Link

D-Link SECURICAM NETWORK DCS-5300 Manuale utente

D-Link

D-Link DCS?6010L Manuale utente

D-Link

D-Link SECURICAM DCS-910 Manuale utente

D-Link

D-Link SECURICAM DCS-910 Manuale utente

D-Link

D-Link DCS-942L Guida all'installazione

D-Link

D-Link DCS-1000 Manuale utente

D-Link

D-Link DCS-2630L Manuale utente

D-Link

D-Link SECURICAM Network DCS-900 Manuale utente

D-Link

D-Link DCS-5222L Manuale utente

D-Link

D-Link DCS-2330L Manuale utente

D-Link

D-Link DCS-2132L Manuale utente

D-Link

D-Link DCS-930-A2 Manuale utente

D-Link

D-Link SECURICAM Network DCS-6620 Manuale utente

D-Link

D-Link DCS-930L Manuale

D-Link

D-Link DCS-2332L Manuale utente

D-Link

D-Link SECURICAM Network DCS-2100G Manuale utente

D-Link

D-Link SECURICAM Network DCS-5300G Manuale utente

D-Link

D-Link DCS-5020L Manuale

D-Link

D-Link DCS-1110 - Network Camera Manuale utente

D-Link

D-Link DCS-2330L Manuale utente

D-Link

D-Link SECURICAM Network DCS-2100+ Manuale utente

D-Link

D-Link SECURICAM Network DCS-2100 Manuale utente

D-Link

D-Link SECURICAM Network DCS-6620 Manuale utente

Manuali Telecamera IP popolari di altre marche

FLIR

FLIR Exx series Manuale utente

Avigilon

Avigilon H4A-BO1-IR Manuale utente

Digital Watchdog

Digital Watchdog DWCA-C128-64 Manuale utente

ShareTech

ShareTech AV1 Manuale utente

Ezviz

Ezviz C6C Manuale utente

Melchioni

Melchioni UCAM 2015 Manuale utente

Geutebruck

Geutebruck G-Cam/ESD-4630 Manuale utente

Arecont Vision

Arecont Vision MegaBall AV3146DN-3310-D-LG Manuale utente

Mitel

Mitel 6800i Series Manuale di servizio

Vitek

Vitek VTC-IR403-212NP Manuale utente

THOMSON

THOMSON DSC - 323W Manuale utente

AVer

AVer FB2027 Manuale utente

ENFORCER

ENFORCER EV-T5105-N2SQ Manuale utente

Wansview

Wansview NC543 Manuale utente

Eneo

Eneo MCB-64A0003M0A Manuale utente

deView electronics

deView electronics CBDNI36F Manuale utente

Swann

Swann SwannEye Manuale utente

LevelOne

LevelOne IP CamSecure Manuale utente