D-Link 1000BASE-TX Manuale utente

1000BASE-TX to

1000BASE-SX/LX

Media Converter

User’s Guide

RECYCLABLE

19071001TSC6002

Rev.1.01

TABLE OF CONTENTS

TABLE OF CONTENTS ..........2

INTRODUCTION.................3

ABOUT MEDIA CONVERTER ......................... 3

PRODUCT FEATURES ......4

INSTALLATION ..................5

SELECTING A SITE FOR THE EQUIPMENT..... 5

CONNECTING TO POWER ............................. 5

INSTALLING IN A CHASSIS ............................ 5

MONITORING THE CONVERTER THROUGH

MANAGEMENT MODULE ............................... 6

LED INDICATOR ........................................... 7

LINK PASS THROUGH FUNCTION ................. 7

SWITCH......................................................... 9

SPECIFICATIONS ............ 10

INTRODUCTION

Thank you for choosing the 1000Base Gigabit Ethernet

Media Converter, The Converter introduced here provides

one channel media conversion between 1000BASE-TX and

1000BASE-FX.

About Media Converter

Media Converter is a network technology specified by IEEE

802.3ab and IEEE 802.3z 1000BASE-TX/FX standards.

PRODUCT FEATURES

yHot-swappable when used with a chassis

yOne-channel media conversion between 1000BASE-TX

and 1000BASE-FX

yFiber media allows: multi-mode fiber and single-mode

fiber using SC connector

yLink Pass Through function

yAuto negotiation of duplex mode on TX port

yAuto MDI/MDI-X for TX port

yFull wire-speed forwarding rate

yFront panel status LEDs

yUsed as a stand-alone device or with a chassis

yHot-swappable when used with a chassis

INSTALLATION

This chapter gives step-by-step installation instructions for

the Converter.

Selecting a Site for the Equipment

As with any electric device, you should place the equipment

where it will not be subjected to extreme temperatures,

humidity, or electromagnetic interference. Specifically, the

site you select should meet the following requirements:

1. The ambient temperature should be between 32 and

104 degrees Fahrenheit (0 to 40 degrees Celsius).

2. The relative humidity should be less than 90 percent,

non-condensing.

3. Surrounding electrical devices should not exceed the

electromagnetic field (RFC) standards for IEC 801-3,

Level 2 (3V/M) field strength.

4. Make sure that the equipment receives adequate

ventilation. Do not block the ventilation holes on each

side of the switch or the fan exhaust port on the side or

rear of the equipment.

5. The power outlet should be within 1.8 meters of the

switch.

Connecting to Power

1. This Converter is a plug-and-play device.

2. Connect the supplied AC to DC power adaptor with a

power voltage of 7.5Vdc/1.5Amp to the DC-Jack on

the converter, and then attach the plug into a standard

AC outlet.

Installing in a Chassis

The Converter can be fit into any of the expansion slots on a

special designed chassis.

yFirst, install the converter onto a carrier supplied with

the chassis:

Step 1- Unscrew and pull out the media converter board.

Step 2- Plug in the media board to any of the vacant slot.

Step 3- Fit the converter onto the carrier and use the screw

to secure it.

Monitoring the Converter through

Management Module

There is a management module that can control this media

converter through the chassis system, this media converter

can be controlled through Web Browser, SNMP and terminal

emulation program.

The management module will detect the default reset on the

DIP switches and display out the status, also the

management module can control the function through the

chassis system.

NOTE: To control the function in a working station, need to collocate together with optional Chassis

System and Management Module.

LED Indicator

The LED indicators give you instant feedback on status of the

converter:

LEDs State Indication

Lights on Power on

Power

(PWR) Lights off Power off

Lights on Linking

Lights Blinking Data transmitting and receiving

Link and

Activity

(LINK/ACT) Lights off Not Linking

Link Pass Through Function

LLCF (Link Loss Carry Forward)

When a device connected to the converter and the TP line loss

the link, the converter’s fiber will disconnect the link of

transmit, so that the other ends will know that there is a

linkage error on this end. And when the Fiber line loss the

link, the converter’s TP will disconnected, and the other end

will know that there is linkage problem exist.

There is a default LLCF setting on this converter.

The table below shows how LLCF function is working:

Fiber

Copper

TX R X

Fiber

Copper

TX R X

RXTX RX TX

Gigabit Switch Gigabit Switch

LIN K 1

LINK 2 LINK 3

LIN K 4

Cable 1

Cab le 2 Cab le 3 Cab le 4

Cab le 5

Med ia

Converter A

Med ia

Converter B

Link Status

Disconnect

Link 1 Link 2 Link 3 Link 4

Cable 1 Off On On On

Cable 2 Off Off Off Off

Cable 3 On On On Off

Cable 4 Off Off Off Off

Cable 5 Off Off Off Off

LLR (Link Loss Return)

When a device connected to the converter and the fiber line

loss the link, the converter’s fiber will disconnect the link of

transmit.

There is a switch to enable or disable the function of the

media converter.

The table below shows how LLR function is working:

Media Converter LLR Auto-Negotiation

A ON OFF

B OFF OFF

Fib e r

Copper

TX R X

Gigabit Switch

LINK 4

LINK 1

Cab le 1

Cab le 2

Media

Converter B

Fib e r

Copper

TX R X

Gigabit Switch

LINK 2

LINK 3

Cab le 3 Cab le 4

Media

Converter A

CopperCopper

Link Status

Disconnect

Link 1 Link 2 Link 3 Link 4

Cable 1 Off Off Off Off

Cable 2 Off On On Off

Cable 3 Off Off Off Off

Cable 4 Off Off Off Off

NOTE: If connecting two converters with LLR function in both end, it is recommended that the monitor

end converter had to turn off the LLR function, and turn on the LLR function of the remote end

converter.

Switch 1 : On -> Forced Mode

Off -> Auto Neg otiation m ode

Switch 2 : On -> LLR enable

Off -> LLR disable

Switch

There is a two pin DIP switch on the module which define as

switch 1 and switch 2:

Switch 1: Fiber mode switch

When the switch was turned to “On”, it means that the

fiber was turned to forced mode, and “Off” for

auto-negotiation mode.

Note: Be sure the opposite end is using the same setting (forced or Auto-negotiation).

And when using two converters at the same time, the two converters MUST set to

forced mode.

Switch 2: LLR

When the switch was turned to “On”, it means that the

LLR was enabled and “Off” for disabled.

Note: When using two converters, don’t enable the both device’s LLR function at the

same time.

SPECIFICATIONS

Standards: IEEE802.3ab 1000BASE-TX

IEEE802.3z 1000BASE-SX/LX

Data Transfer

Rate: 1488000pps for 1000Mbps

Duplex Mode: Full Duplex Mode

LED indicators: PWR, LNK/ACT

Cable 1000BASE-T --

4 pair Cat. 5, EIA/TIA-568 100-ohm

screened twisted-pair (STP), up to 100m

1000BASE-SX --

62.5/125μm multi-mode fiber optic cable,

up to 220m

50/125μm multi-mode fiber optic cable, up

to 550m

1000BASE-LX --

9/125 μm single-mode fiber optic cable,

DMC-810SC up to 10km

DMC-880SC up to 80km

Dimensions L120 × W88 × H25 mm

Weight 305 g

Power External power adaptor 7.5V 1.5A

Media Interface: RJ-45, SC

EMI Compatiblity: FCC Class B

CE Certification, Class B

VCCI Class B

Temperture: Storage: -10°C ~ 70°C

Operating: 0°C ~ 40°C

Humidity: 10% ~90% non-condensing

Power

Consumption:

5.5 Watts (maximum)

Altri manuali per 1000BASE-TX

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali D-Link Convertitore multimediale

D-Link

D-Link DUB-AV200 Manuale utente

D-Link

D-Link DE-856SC Manuale utente

D-Link

D-Link DUB-AV300 Istruzioni per il montaggio

D-Link

D-Link DMC-805G Manuale utente

D-Link

D-Link DSB-V100 Manuale utente

D-Link

D-Link DMC-920 Manuale utente

D-Link

D-Link DMC-810SC Manuale utente

D-Link

D-Link DMC-515SC Manuale utente

D-Link

D-Link DIS-M100G-SW Manuale utente

D-Link

D-Link 100Base-FX Manuale utente

D-Link

D-Link DMC-300SC - Media Converter - External Manuale utente

D-Link

D-Link 10/100BASE-TX to 100BASE-FX Media Converter Manuale utente

D-Link

D-Link DMC-515SC Manuale utente

D-Link

D-Link DMC-530SC Manuale utente

D-Link

D-Link DMC-G01LC Manuale utente

D-Link

D-Link DMC-300SC - Media Converter - External Manuale utente

D-Link

D-Link DMC-G01LC Manuale utente

D-Link

D-Link DFE-855 Manuale utente

D-Link

D-Link DMC 1000 - Modular Expansion Base Manuale utente

D-Link

D-Link 1000BASE-TX Manuale utente

D-Link

D-Link 1000BASE-SX Manuale utente

D-Link

D-Link DMC-G01LC Manuale utente

D-Link

D-Link DVS-210-1 Manuale utente

D-Link

D-Link DMC-1530SC Manuale utente

Manuali Convertitore multimediale popolari di altre marche

SoundTraxx

SoundTraxx Blunami BLU-2200 Manuale utente

SPROLINK

SPROLINK VA1 Manuale utente

Acclaim Lighting

Acclaim Lighting DDC-1-AC Manuale utente

Nikon

Nikon AF-S TC-20E III Manuale utente

Axis

Axis AXIS Q7406 Manuale utente

Omega

Omega TAC80B-J Manuale utente

Zoom

Zoom Thunderbolt TAC-2R Manuale utente

OST

OST iConverter 10/100M Manuale utente

Vertiv

Vertiv Netsure Manuale utente

birddog

birddog MINI Manuale utente

Roland

Roland GI-10 Manuale utente

Wallenstein

Wallenstein WX310 Manuale utente

Pace

Pace MSS 200-1 Manuale utente

Solar Converters

Solar Converters EQ 12/24-50 Manuale utente

CYP

CYP EL-7400V Manuale utente

TIE

TIE MIDI 1i1o Manuale utente

DCS

DCS Vivaldi Upsampler Manuale utente

Westermo

Westermo MCW-211 SERIES Manuale utente