D-Link DWL-3600AP Manuale utente

This document will guide you through the

basic installation process for your new

D-Link 802.11n Unied Access Point.

Building Networks for People

DWL-3600AP

Documentation also available

on CD and via the D-Link

Website

Quick Installation Guide

802.11n Unied Access Point

Quick Installation Guide

2  D-Link DWL-3600AP Quick Install Guide

ENGLISH

About This Guide

This installation guide provides basic

instructions for installing the DWL-3600AP

802.11n Unied Access Point on your network.

For additional information about how to use the

Access Point, please see the User Manual, which

is available on the CD included in this package or

from the D-Link support website.

2.4 GHz – When this LED is lit up, the access

point’s 2.4 GHz radio is enabled. It will

blink when there is wireless trafc.

LAN – When this LED is lit up, the device’s

Ethernet port is connected to an active

router or switch. The light will blink

when there is trafc going through

the port.

POWER – When the LED is lit up, the access

point is powered and ready for use.

Unpacking the Product

System Requirements

Open the shipping carton and carefully unpack its

contents. Please consult the packing list located

in following information to make sure all items are

present and undamaged. If any item is missing

or damaged, please contact your local D-Link

reseller for replacement.

- DWL-3600AP 802.11n Power over Ethernet

(PoE) Unied Access Point

- Mounting Ring

- Ethernet Cable

- Console Cable*

- CD-ROM

- Ceiling Bracket (3 sets, sizes are 9/16", 14/16",

and 1 1/2")

NOTE no PSU supplied. To power the units

use an D-Link PoE switch or the D-Link

DPE-101GI PoE injector.

*The console cable is an optional accessory and

not included in the package in Armenia, Azerbaijan,

Belarus, Georgia, Israel, Kaliningrad, Kazakhstan,

Kyrgyzstan, Latvia, Lithuania, Moldova, Mongolia,

Russia, Turkey, Turkmenistan, Ukraine, and

Uzbekistan. If a cable is required, please contact

your reseller to order it (Model: ACS-AP-CONSOLE).

- CD-ROM Drive

- Ethernet port or installed Ethernet adapter

- Internet Explorer 7.0, Safari 5.0, Firefox 4.0,

Chrome 20 or higher

Optional Accessories

- PoE Base Unit (Model: DPE-101GI)

Figure 2. DWL-3600AP Rear Panel

Hardware Overview

Figure 1. DWL-3600AP LEDs

RESET

2.5A

Power Receptor

(*Note no longer

used, replaced

by PoE)

LAN Port (PoE)

Reset Port

Console Port

LEDs

Interfaces

D-Link DWL-3600AP Quick Install Guide 3

ENGLISH

Power on the access point

To power on the DWL-3600AP, you can use ONE of

the following methods:

1. Plug one end of an Ethernet cable into the LAN

port of the DWL-3600AP and the other end into

a port on a PoE switch.

2. Purchase separately a DPE-101GI PoE injector

if you need to connect the Access Point without

a PoE Switch.

Congure the access point

To set up and manage the DWL-3600AP, please

follow the instructions below.

Mounting Options

You can mount a DWL-3600AP access point on any

of the following types of surfaces:

• Solid surface wall or ceiling

• Tabletop

Cable Requirement

Use a CAT 5 cable with an even sheath.

The Ethernet ports on the DWL-3600AP access

point cannot accept a CAT 5 cable that has an

uneven sheath; the RJ-45 connector on the cable

will not fit properly into the receptacle on the access

point.

Wall Installation Recommendations

If you plan to install the DWL-3600AP on a wall or

other vertical surfaces, orient the top of the access

point (the side with the LEDs) toward the intended

coverage area. The radio antennas transmit through

the top of the access point but not through the

bottom (where the bracket is).

• Power up the access point by connecting

it to any one of the POE switch’s Ethernet

ports. The default IP address of the access

point is 10.90.90.91. You will be prompted

for an ID and password when you try to

log into the web management interface.

Enter admin as the ID, and admin as the

password.

Installation

ComputerDWL-3600AP

PoE switch

Warning: The DWL-3600AP is designed to

receive PoE power only from an 802.3af compliant

source, or from a D-Link-approved power injector.

Connecting an access point to a Power over

Ethernet (PoE) device that is not approved by D-Link

can damage the equipment.

4  D-Link DWL-3600AP Quick Install Guide

ENGLISH

Solid Wall or Ceiling

Installation

1. Place the plastic wall mounting ring on a

wall or ceiling.

2. Mark the points where you will insert the

screws. Take out the mounting ring.

3. Drill holes in the marked points and

insert the plastic wall anchors.

4. Use the supplied screws to attach the

mounting ring to the wall.

7. Plug the CAT 5 cable into the LAN port

on the access point.

5. To attach the access point to the

mounting ring, rst locate the right side

of the access point that has a small lock

symbol on it, and make sure to line up

this side with the side of the mounting

ring that has Open - Close written on it.

6. Twist counterclockwise to lock the access

point onto the ring. The lock symbol on

the access point must point directly to the

Close text on the mounting ring.

Figure 3. Insert screws through mounting ring

Figure 4. Insert access point into mounting ring

Figure 5. Plug cable into access point

D-Link DWL-3600AP Quick Install Guide  5

ENGLISH

Mounting With A Ceiling Bracket

4. Plug the CAT 5 cable into the LAN port on

the access point.

1. Clip two ceiling brackets onto the ceiling

panels. Make sure both brackets are in

line with each other.

2. Use the provided screws to attach the

mounting ring to the ceiling bracket.

3. Place the DWL-3600AP’s male

bracket in the mounting ring’s female

bracket. Rotate the DWL-3600AP

counterclockwise to lock it in position.

Installation

Ceiling bracket

Ceiling crossbar

6  D-Link DWL-3600AP Quick Install Guide

ENGLISH

Appendix A - Statements

FCC Statement:

Federal Communication Commission Interference Statement

This equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection

against harmful interference in a residential installation. This equipment generates, uses and can radiate

radio frequency energy and, if not installed and used in accordance with the instructions, may cause

harmful interference to radio communications. However, there is no guarantee that interference will not

occur in a particular installation. If this equipment does cause harmful interference to radio or television

reception, which can be determined by turning the equipment off and on, the user is encouraged to try

to correct the interference by one of the following measures:

● Reorient or relocate the receiving antenna.

● Increase the separation between the equipment and receiver.

● Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

● Consult the dealer or an experienced radio/TV technician for help.

FCC Caution: Any changes or modications not expressly approved by the party

responsible for compliance could void the user’s authority to operate this equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and (2) this device must accept any interference

received, including interference that may cause undesired operation.

For product available in the USA/Canada market, only channel 1~11 can be operated. Selection of other

channels is not possible.

This device and it's antennas(s) must not be co-located or operating in conjunction with any other

antenna or transmitter except in accordance with FCC multi-transmitter product procedures.

IMPORTANT NOTE:

FCC Radiation Exposure Statement:

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.

This equipment should be installed and operated with minimum distance 20cm between the radiator &

your body.

IC Statement:

This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the

following two conditions: (1) this device may not cause interference, and (2) this device must accept any

interference, including interference that may cause undesired operation of the device.

Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts

de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire

de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si

le brouillage est susceptible d'en compromettre le fonctionnement.

This device and it's antennas(s) must not be co-located or operating in conjunction with any other

antenna or transmitter except in accordance with IC multi-transmitter product procedures.

Cet appareil et son antenne (s) ne doit pas être co-localisés ou fonctionnement en association avec une

autre antenne ou transmetteur.

D-Link DWL-3600AP Quick Install Guide 7

ENGLISH

IMPORTANT NOTE:

IC Radiation Exposure Statement:

This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled

environment. This equipment should be installed and operated with minimum distance 20cm between

the radiator & your body.

Cet équipement est conforme aux limites d'exposition aux rayonnements IC établies pour un

environnement non contrôlé. Cet équipement doit être installé et utilisé avec un minimum de 20cm de

distance entre la source de rayonnement et votre corps.

For product available in the USA/Canada market, only channel 1~11 can be operated. Selection of other

channels is not possible.

Pour les produits disponibles aux États-Unis / Canada du marché, seul le canal 1 à 11 peuvent être

exploités. Sélection d'autres canaux n'est pas possible.

低功率電波輻射性電機管理辦法

第十二條經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得擅自變更頻率、

加大功率或變更原設計之特性及功能。

第十四條低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現有干擾現象時，應立即停

用，並改善至無干擾時方得繼續使用。前項合法通信，指依電信法規定作業之無線電通信。低功率射頻電

機須忍受合法通信或工業、科學及醫療用電波輻射性電機設備之干擾。

CE Mark Warning:

This is a Class B product. In a domestic environment, this product may cause radio interference, in

which case the user may be required to take adequate measures.

Power Usage

This device is an Energy Related Product (ErP) with High Network Availability (HiNA), and automatically

switches to a power-saving Network Standby mode within 1 minute of no packets being transmitted. If it

is not needed during certain periods of time, it can be unplugged to save energy.

Network Standby: 6.4 watts

8  D-Link DWL-3600AP Quick Install Guide

ENGLISH

TECHNICAL SUPPORT

dlink.com/support

TECHNISCHE UNTERSTÜTZUNG

ASSISTANCE TECHNIQUE

ASISTENCIA TÉCNICA

SUPPORTO TECNICO

TECHNISCHE ONDERSTEUNING

POMOC TECHNICZNA

TECHNICKÁ PODPORA

TECHNIKAI TÁMOGATÁS

TEKNISK SUPPORT

TEKNISK STØTTE

TEKNINEN TUKI

ASSISTÊNCIA TÉCNICA

ΤΕΧΝΙΚΉ ΥΠΟΣΤΉΡΙΞΗ

TEHNIČKA PODRŠKA

TEHNIČNA PODPORA

SUPORT TEHNIC

ТЕХНИЧЕСКА ПОДДРЪЖКА

Ver 1.10(EU) 2015/11/09

Altri manuali per DWL-3600AP

Indice

Altri manuali D-Link Punto di accesso wireless

D-Link

D-Link DAP-3662 Manuale utente

D-Link

D-Link DAP-3662 Manuale utente

D-Link

D-Link AMPLIFI DAP-1525 Manuale utente

D-Link

D-Link xtreme n duo dap-1522 Manuale utente

D-Link

D-Link DAP-2590 - AirPremier N Dual Band PoE Access... Manuale utente

D-Link

D-Link AirPremier N DAP-2310 Manuale utente

D-Link

D-Link AirPremier N DAP-2310 Manuale utente

D-Link

D-Link DAP-3666 Manuale utente

D-Link

D-Link DAP-3220 Manuale utente

D-Link

D-Link DAP-3520 - AirPremier N Dual Band Exterior PoE Access... Manuale utente

D-Link

D-Link DWL-3600AP Manuale di servizio

D-Link

D-Link DWL-6620APS Manuale utente

D-Link

D-Link DWL-G700AP - AirPlus G Access Point Manuale utente

D-Link

D-Link AirXpert DWL-7000AP Manuale utente

D-Link

D-Link AirPremier N DAP-2360 Manuale utente

D-Link

D-Link DWL-2700AP - AirPremier Outdoor Wireless Access... Manuale utente

D-Link

D-Link Air Premier DAP-2695 Manuale utente

D-Link

D-Link AirPlus DWL-900AP+ Manuale utente

D-Link

D-Link DBA-1520P Manuale utente

D-Link

D-Link DWL-3200AP - AirPremier - Wireless Access... Manuale utente

D-Link

D-Link DAP-1360 Manuale utente

D-Link

D-Link AirPremier DWL-7700AP Manuale utente

D-Link

D-Link AirPlus DWL-900AP Manuale utente

D-Link

D-Link D DWL-8200AP DWL-8200AP Manuale utente

Manuali Punto di accesso wireless popolari di altre marche

Ubiquiti

Ubiquiti NanoStation NSM2 Manuale utente

Cisco

Cisco Aironet 1550 Series Manuale utente

Aruba

Aruba IAP-335 Manuale utente

Advantek Networks

Advantek Networks AWN-AP-54MR Manuale utente

IP-COM

IP-COM AP355 Manuale utente

Buffalo

Buffalo AirStation WLA-L11G Manuale utente

EnGenius

EnGenius EnStationACv2 Manuale utente

xG Technology

xG Technology xMax CN1300 Manuale utente

Widelink

Widelink ezWave WAP-1100 Series Manuale utente

Edimax

Edimax CAP1200 Manuale utente

Ubiquiti

Ubiquiti LBE-5AC-Gen2 Manuale utente

Aruba

Aruba AP-203R Manuale utente

LuXout Shades

LuXout Shades LUXSHADE MOTION Manuale utente

CreatComm

CreatComm TB5F Manuale utente

SineDigital

SineDigital MW-1500AP(H) Manuale utente

TP-Link

TP-Link AP9650 V1 Manuale utente

Draytek

Draytek VIGORAP 902 Manuale utente

EnGenius

EnGenius EAP350 Manuale utente