Dakota Digital BIM-04 Manuale utente

MAN#650327:A

BIM-04

Bus Interface Module for fluid temperature

(Sensors are sold separately)

BLUE or RED

BROWN or BLACK

Connect to main

chassis ground

+12V

KEY ON POWER

(fused 5 - 20 AMP max)

setup/status switch

To gauge control box

or another BIM

Channel 3 temperature sensor

Channel 2 temperature sensor

Channel 1 temperature sensor

TEMP #1

TEMP -

PWR

GND

BIM-04-1

TEMPERATURE

TEMP #2

TEMP -

TEMP #3

TEMP -

I/O

www.dakotadigital.com

techsupport@dakotadigital.com

605-332-6513

BLUE or RED

BROWN or BLACK

BLUE or RED

BROWN or BLACK

This Bus Interface Module has inputs for up to three temperature sensors, Dakota Digital part number SEN-04-5.

Each input can be configured individually. There are two interface (I/O) ports on the module. Either one can be

connected to the gauge system or to another module, allowing several units to be daisy chained together. Do not

connect the I/O port to anything other than a Dakota Digital gauge or BIM. Do not mount the module in the engine

compartment; it should be mounted in interior of the vehicle.

Each sensor connected to the bus needs a unique ID number assigned to it. This module has three inputs so it can

use one, two, or three ID numbers. Each of the three inputs can be assigned an ID from 1 – 16, or turned off. The

factory default ID numbers are 1, 2, and OFF for the three inputs respectively. The factory default labels are TEMP for

all inputs.

Labels available for each input are:

TEMP - generic temperature input. This will display TEMP x, Tx, or TEMPERATURE CHx where x is a

number from 1 – 8 corresponding to the module ID number. ID’s over 8 will start over at 1.

WATER - dual water temperature input for right hand side water temp sensor. When this is active the gauge

system water display will show the higher of the left and right sensors. The message display will show

both temperature readings side by side. The gauge system water temp sensor should be installed in

the left hand side.

OIL - oil temperature input. This will display OIL, OT, or OIL TEMP.

TRANS - transmission temperature input. This will display TRANS, TT, or TRANS TEMP.

DIFF - rear differential temperature input. This will display DIFF, DT, or DIFF TEMP.

Specs for each input are:

Sensor Range high warning

TEMP SEN-04-5 only 100 - 320F 131 – 320

WATER SEN-04-5 only 100 - 320F none (set by gauge system water temp)

OIL SEN-04-5 only 100 - 320F 131 – 320

TRANS SEN-04-5 only 100 - 320F 131 – 320

DIFF SEN-04-5 only 100 - 320F 131 – 320

Temperature unit will follow the unit set for the main water temp gauge, Fahrenheit or Celsius.

The sensor has 1/8” NPT threads. Adapters are available to convert to other thread sizes.

MAN#650327:A

To set or change the ID numbers:

•Hold the switch beside the BIM terminal strip while turning the key on. The BIM display will show the current

revision code while this is held.

•Release the switch. The display will show “-C-”.

•Press the switch. The BIM display will show “C-1”.

•Release the switch. The display will show the current ID for channel 1.

•Press and release the switch to change the setting from 1-16 or OFF.

•Press and hold the switch to save the setting. The BIM display will show “C-2”.

•Release the switch. The display will show the current ID for channel 2.

•Press and release the switch to change the setting from 1-16 or OFF.

•Press and hold the switch to save the setting. The BIM display will show “C-3”.

•Release the switch. The display will show the current ID for channel 3.

•Press and release the switch to change the setting from 1-16 or OFF.

•Press and hold the switch to save the setting. The BIM will restart with the new settings.

The labels and warning points are set up through the gauge display system.

Only VFD3/3X controls with a plastic case support adding BIM’s.

For VFD3, VFD3X, and VHX systems follow these steps:

•Make sure the BIM units are all connected to the gauge control box with the 3.5mm data cables.

•Hold the SW1 switch from the gauge system control box while turning the key on. The message display

should show SETUP.

•Release SW1.

•Press and release SW1 until BIM is shown on the message display.

•Press and hold SW1. The message display should show SCAN followed by the number of BIM channels

detected. Release SW1.

•If 0 is shown, check all connections and then press and hold SW1 with SCAN shown to retry reading the

modules.

•Otherwise, if any other number is shown, press and release SW1 until SETUP is shown.

•Press and hold SW1 until the speed display shows “ – ” or the message changes.

•Release SW1. On the VFD3 systems the message display will show the label assigned to the first channel

found and the speed display will show “C” followed by the channel ID number. On the VHX systems the

message display will show “CH” followed by the channel ID number on one line and the label currently

assigned on the second line.

•Press and release SW1 until the desired channel ID number is shown.

•Press and hold SW1. The message display will show “LABEL”.

•Release SW1. The message display will show the label assigned to this channel.

•Press and release SW1 until the desired label is shown.

•Press and hold SW1. The message display will show “WARN” (this is skipped if WATER was selected for the

label).

•Release SW1. The message display will show “H” followed by the current high warning point or will flash the

warning point.

•Press and release SW1 to change the high warning point to the desired value.

•Press and hold SW1. The message display will now show “DONE”.

•This can be repeated for additional channels, or the key can be turned off to exit setup.

MAN#650327:A

Troubleshooting quick tips:

While the BIM is operating, the dot in the upper left corner of the display will indicate the status. On steady indicates it

is powered up but not receiving any bus activity. Flashing indicates it is communicating on the bus.

To see the sensor and channel status on the BIM display, press and hold the switch. The display will cycle through

four screens. The first will show the sensor input status. Each digit on the display will show the status for one of the

channels. ‘E’ indicates there is a bus ID conflict on that channel ID. ‘-’ indicates the sender is connected properly. ‘H’

indicates the sender is not connected or the signal is too high. ‘L’ indicates the sender is shorted to ground or is too

low. If the input is turned off the digit will be blank.

The second screen will show the ID assigned to channel 1. The third screen will show the ID assigned to channel 2.

The forth screen will show the ID assigned to channel 3.

Troubleshooting guide.

Problem Possible cause Solution _

Sensor does not show on PWR terminal does not have power. Connect to a location that has power.

gauge readout. GND terminal does not have a good Connect to a different ground location.

BIM will not light up at all. ground.

Module is damaged. Return for service. (see instructions) _

Sensor does not show on Interface cable is not connected. Connect the supplied 3.5mm data cable between the module and

gauge readout. the gauge control box.

BIM has a steady dot lit Interface cable is loose. Make sure both ends of the cable are seated in securely.

On VHX systems, the BIM display Follow instructions in VHX manual to enable the BIM display screen.

for this channel is disabled.

Another BIM is set with the same Test module works when connected to control box alone. Change ID’s

channel IDs. on one of the modules so each module uses unique IDs. _

Gauge lights up, but does Loose connection on sensor wires. Inspect and reconnect wires.

not read correctly. Connector not seated on sensor. Reattach the sensor plug, making sure the locking tab clicks in place.

Channel sensor label setup is incorrect. Change label by entering BIM setup through gauge system.

Voltage or wiring problem in the Check wiring harness for loose or damaged wires.

vehicle wiring harness.

Gauge lights up, but displays SND terminal is shorted to ground. Check wire for damaged insulation. Replace if necessary.

“---”. (‘L’ on BIM) Sender is damaged. Replace sender.

Gauge lights up, but displays Sender is not connected to gauge. Connect SND terminal on gauge to sender terminal.

“EEE”. (‘H’ on BIM) Wire between gauge and sender is Test and replace wire.

broken.

Sender is damaged. Replace sender.

Module is damaged. Return module for service. (see instructions)

BIM display shows ì”88:8” Data cable is damaged. Inspect and replace 3.5mm data cable.

Another module on the bus is damaged Inspect other modules on the data bus.

or connected improperly.

MAN#650327:A

SERVICE AND REPAIR

DAKOTA DIGITAL offers complete service and repair of its product line. In addition, technical

consultation is available to help you work through any questions or problems you may be having installing

one of our products. Please read through the Troubleshooting Guide. There, you will find the solution to

most problems.

Should you ever need to send the unit back for repairs, please call our technical support line, (605)

332-6513, to request a Return Merchandise Authorization number. Package the product in a good

quality box along with plenty of packing material. Ship the product by UPS or insured Parcel Post. Be sure

to include the RMA number on the package, and include a complete description of the problem with RMA

number, your full name and address (street address preferred), and a telephone number where you can be

reached during the day. Any returns for warranty work must include a copy of the dated sales receipt from

your place of purchase. Send no money. We will bill you after repair.

Dakota Digital Limited Lifetime Warranty

DAKOTA DIGITAL warrants to the ORIGINAL PURCHASER of this product that should it, under

normal use and condition, be proven defective in material or workmanship for the lifetime of the original

vehicle it was installed in, such defect(s) will be repaired or replaced at Dakota Digital’s option.

This warranty does not cover nor extend to damage to the vehicle’s systems, and does not cover

removal or reinstallation of the product. This Warranty does not apply to any product or part thereof which

in the opinion of the Company has been damaged through alteration, improper installation, mishandling,

misuse, neglect, or accident.

This Warranty is in lieu of all other expressed warranties or liabilities. Any implied warranties,

including any implied warranty of merchantability, shall be limited to the duration of this written warranty. No

person or representative is authorized to assume, for Dakota Digital, any liability other than expressed

herein in connection with the sale of this product.

Altri manuali Dakota Digital Unità di controllo

Dakota Digital

Dakota Digital BIM-13-2 Manuale utente

Dakota Digital

Dakota Digital VFD III Series Manuale utente

Dakota Digital

Dakota Digital DCC-4000 Guida all'installazione

Dakota Digital

Dakota Digital Odyssey ODY-19-3 Manuale utente

Dakota Digital

Dakota Digital BIM-01-2-FTCH Manuale utente

Dakota Digital

Dakota Digital BIM-22-3 Manuale utente

Dakota Digital

Dakota Digital BIM-17-2 Manuale utente

Dakota Digital

Dakota Digital BIM-01-2-HSN2 Manuale utente

Dakota Digital

Dakota Digital BIM-05-1 Manuale utente

Dakota Digital

Dakota Digital GPS-50-1 Manuale utente

Dakota Digital

Dakota Digital BIM-12-1 Manuale utente

Dakota Digital

Dakota Digital BIM-19 Manuale utente

Dakota Digital

Dakota Digital BIM-22-2 Manuale utente

Dakota Digital

Dakota Digital BIM-17-2 Manuale utente

Dakota Digital

Dakota Digital BIM-17-1 Manuale utente

Dakota Digital

Dakota Digital BIM-03-2 Manuale utente

Dakota Digital

Dakota Digital BIM-19-2 Manuale utente

Dakota Digital

Dakota Digital BIM-01-2-EDBK Manuale utente

Dakota Digital

Dakota Digital BIM-01-2-AEM Manuale utente

Dakota Digital

Dakota Digital BIM-12-2 Manuale utente

Dakota Digital

Dakota Digital GPS-50-2 Manuale utente

Manuali Unità di controllo popolari di altre marche

Festo

Festo Compact Performance CP-FB6-E Manuale elenco delle parti

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuale utente

JS Automation

JS Automation MPC3034A Manuale utente

JAUDT

JAUDT SW GII 6406 Series Guida rapida

Spektrum

Spektrum Air Module System Manuale utente

BOC Edwards

BOC Edwards Q Series Manuale utente

KHADAS

KHADAS BT Magic Manuale utente

Etherma

Etherma eNEXHO-IL Manuale utente

PMFoundations

PMFoundations Attenuverter Manuale utente

GEA

GEA VARIVENT Manuale utente

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuale utente

Altronix

Altronix LINQ8PD Istruzioni per il montaggio

Eaton

Eaton Powerware Series Manuale utente

WAGO

WAGO 750-407/040-000 Manuale utente

Sony

Sony CCU-590 Manuale utente

Graco

Graco 25D614 Manuale utente

Task Force Tips

Task Force Tips YE-RF-900 Manuale di programmazione

Shini

Shini SPV-U Series Manuale utente