Dancover GH82121 Manuale utente
13-05-2015
for
Polytunnel greenhouse
4x10x2,4m
Manual
Safety Advice
Attention
In some countries approval is needed to set up a marquee/tent larger than 75 m2. It is
your responsibility to comply with local rules and regulations and to ensure that the
marquee/tent is assembled correctly.
In case of bad weather conditions, it is your responsibility to ensure the marquee/tent is
safely secured and that the marquee/tent does not cause damage to others.
close to the tent.
The marquee/tent must be safely secured. We recommend you secure your marquee/tent
with straps and pegs as soon as it is assembled.
Make sure to check if the marquee/tent is covered by your home contents
insurance.
Marquees/tents must be evacuated under extreme weather conditions.
In the event of snow always remove snow from the roof of the marquee/tent regularly to
prevent snow from building on the roof as heavy snow can cause the marquee/tent to
collapse.
In the event of rain there is a risk of rain puddles building up on top of the roof of the
marquee/tent. Heavy rain puddles can cause the roof to collapse. It is your responsibility
to ensure rain puddles do not build up. As a precaution, make sure the roof of the
marquee/tent is stretched out properly and adequately over the side frames of the
marquee/tent and remove rain water regularly.
Do not unpack or repack your marquee/tent in freezing temperatures. In case of
temperatures below zero always unpack and repack your marquee/tent indoors to avoid
the risk of cracking parts.
The marquee/tent must be totally dry before you repack and store it to avoid mildew.
Warranty Information
Please visit dancovershop.com for information on warranty.
Please always check our website for the latest safety advice and manuall.
This structure is not tested for snow and wind loads. We always recommend that you
remove snow from the roof.
Part No Length: [cm]
1A
1B
1C
1D
1E
2131
2A 131
3121
4126
5180
680
7120
8114
8A 114
9172
10 90
11 170
12
13
14
15
16 125
17 122
21 13
22 8
23
24
25
26
27
Name of the part
Number [pcs.]
Front one-side bow
2
Side reversible bow
14
One-side side bow R
2
One-side side bow L
2
Front horizontal connector with coupler
4
Horizontal connector
40
Top reversible bow
7
Front horizontal connector
2
Post
18
Corner reinforcement
4
Bows connector
18
Vertical connector (door frame)
2
Door vertical cross bar
2
Door horizontal cross bar
2
Top horizontal reinforcement
9
Top horizontal reinforcement with coupler
9
Reversible clamp
16
Middle connector
14
Door reinforcement
1
Clamp fi25
28
Horizontal connector (rolling device)
16
Corner connector
4
Horizontal rolling connector (rolling device)
16
Horizontal connector ø22 middle L= 13
14
Horizontal connector ø22 end L= 8
4
Bolt M6x40 + nut
265
Bolt M6x60 + nut
18
Crank
2
Hook(holdfast) 6x40 + nut x 2 pcs
36
Nut M8
8
Cover is assembled with the help of plastic clips. When
assembling the cover, please cut out the shape of the front
and back wall and rectandular shape for the doors and
attach them to the corresponding construction parts. The
rest of the cover is already precut. The main part should be
placed along the whole tunnel from the top of the front wall
to the top of the end wall. The pieces of cover for the
curtain should be attached to the horizontal connector.
Assembly
Tunnel construction consists of tubular parts, hot-dip galvanised in and out,
postfabricated, which prevents them from corrosion. Assemble tubes according to
the drawing, cut the cover according to the drawing (only the front and the back
wall and doors; the rest is precut), put it on the tunnels construction stretching it
and pin it to the tubular part with the clips. Construction can be easily transported
to another place or reassembled.
Assembly manual – TUNNEL 4,0 x 2,4 x …m
1. All construction parts of the construction correspond to the
specification.
Distance between bows is 1,25m. Depending on the number of bows the length of
the tunnels increases 1,25m with each bow. Please find below the drawing with
tunnel dimensions.
2 Assembly of the front and back wall with door
This is how the front/back wall should be assembled. The door frame and the door
is assembled with the help of reversible clamps (nr 13 in specification).
3 Cover/moscitoe net assembly.
COVER
Cover stretched from the top of the tunnel
must be attached to the cover holding strip.
The rest of the cover must be attached to the
rolling mechanism with clips
Moscitoe net is
attached to the tube
behind the cover
holding strip with (the
help of) clips
Both cover and the
other end of moscitoe
net must be attached
here. The rest of the
cover must be dug
into the ground
Cover which must be dug into
the ground
“Cover, hobby tunnel 4,0x2,4xL (m)”
10,5m 4,5m
2,25m
Cover
T
he “Main part of the tunnel” piece is extra long on both sides. The extra cover must be dug into the
g
round to secure the polytunnel greenhouse.
C
onnect the cover to the frame with the easy clip-on connector system.
Questo manuale è adatto per i seguenti modelli
2
Indice
Altri manuali Dancover Kit serra
Dancover
Dancover Orangery GH170010 Manuale utente
Dancover
Dancover Orangery Manuale utente
Dancover
Dancover AC120070 Manuale utente
Dancover
Dancover GH152080 Manuale utente
Dancover
Dancover TITAN Arch 130 Manuale utente
Dancover
Dancover STRONG 3x4 m Manuale utente
Dancover
Dancover 2m Series Manuale utente
Dancover
Dancover GH152200 Manuale utente
Dancover
Dancover GH16050 Manuale utente
Dancover
Dancover ARROW 3m Series Manuale utente
Dancover
Dancover GH152190 Manuale utente
Dancover
Dancover TITAN Arch+ 320 Manuale utente
Dancover
Dancover GH152015 Manuale utente
Dancover
Dancover TITAN Arch 90 Manuale utente
Dancover
Dancover GH152200 Manuale utente
Dancover
Dancover GH117000 Manuale utente
Dancover
Dancover GH152190 Manuale utente
Dancover
Dancover ZEN 4.73M2 Manuale utente
Dancover
Dancover GH152100 Manuale utente
Dancover
Dancover Polytunnel Greenhouse Manuale utente
