Danfoss DHP-A Manuale utente

VMBMF302

Installation instruction

Outdoor unit

DHP-A, DHP-AL

Contents

1 Installing the outdoor unit ...........................2

1.1 Check the delivery ..........................................2

1.2 Assembling the stand .......................................2

1.3 Preparing the outdoor unit ..................................2

1.4 Assembling the outdoor unit on the stand . . . . . . . . . . . . . . . . . . .3

1.5 Assembling the front cover ..................................3

1.6 Assembling the cover and cover plate .......................4

1.7 Assembling the defrost sensor...............................6

2VMBMF302

1 Installing the outdoor unit

It is essential that the outdoor unit is installed by two people.

1.1 Check the delivery

The outdoor unit is delivered as three items:

• the outdoor unit, on a wooden pallet

• a box containing the stand, adjustable feet and all the necessary screws

• aboxcontainingcovers

The following tools are required for assembly and installation:

• Wrench, or equivalent, 10 mm

• Wrench, or equivalent, 13 mm

• Screwdriver, or equivalent, torx TX25

• Cross head screwdriver

• Drill bit Ø 3 mm

• MillingcutterØ 6 mm, or equivalent

• Drill

Check that the following screws have been supplied:

• 8 x M6x10, hex screw

• 4 x M6x10, hex screw

• 5 x M6x15, torx TX25

• 2 x panel screws, crosshead

1.2 Assembling the stand

1. Screw the two horizontal struts together (1) using the two ends (2) as illustrated below. Use 8 x M6x10 screws. The bent

edges of the horizontal struts must be facing upwards and inwards.

Figure 1: Assembling the stand.

2. Screw the adjustable feet (3) into the holes under the ends.

1.3 Preparing the outdoor unit

While the outdoor section remains on the pallet it should be prepared for placing on the stand. Carry out the following:

3. There are three M6x20 screws on the lower edge of the outdoor unit. Unscrew them so that 2-3 mm of the thread

remains. Use a torx TX25 screwdriver, or equivalent.

4. Raise the outdoor unit. NOTE! Do not lift the side plates.

5. Remove the side plates. They are held in place by clamps and so are removed by pulling outwards.

6. Remove all four screwed lifting eyes. Use a 13 mm wrench, or equivalent.

Slit

Bent edge

VMBMF302

1.4 Assembling the outdoor unit on the stand

7. Lift the outdoor unit into the place on the stand.

Figure 2: Lift the outdoor unit onto the stand.

8. Screw the outdoor unit onto the stand. Use 4 x M6x20 screws. It may be necessary to push and pull the stand slightly in

order to get the screw holes to align.

9. Reinstall the side panels.

1.5 Assembling the front cover

⚠ Leave the transport protection on the corners of the front panel in place during installation to prevent scratches on the

outer section.

10. Hook the lower edge of the front cover onto at least one of the three screws in the bottom edge of the stand.

11. Secure the upper edge of the front panel temporarily in the centre hole. Use 1 x M6x15 torx TX25.

12. Align all the three screws in the lower edge.

13. Screw the three screws in the lower edge fully. Use a torx TX25 screwdriver, or equivalent.

4VMBMF302

14. Secure the upper edge of the front cover. Use 3 x M6x15 torx TX25.

Figure 3: Secure the front cover.

15. Remove the transport protection on the four corners of the front panel.

Figure 4: Transport protection.

1.6 Assembling the cover and cover plate

16. Hook the cover at the front edge on the front cover.

Figure 5: Hook the front cover into place.

VMBMF302

17. Secure the cover using a screw on each side. Use 2 x cross head screws.

If the cover does not align with the side cover plates it may be necessary to drill new Ø 3 mm holes:

•Mark for the new holes

•Lift off the cover

•Drill the holes

•Install and screw the cover into place

Figure 6: Screw the front cover into place.

18. Hook the cover onto the stand.

Figure 7: Hook the cover into place.

6VMBMF302

1.7 Assembling the defrost sensor

Figure 8: Hook the defroster sensor into place.

18. Slide the mounting for the defroster sensor into the hole on the reverse of the outdoor unit until it hooks into place on

the edge.

19. Secure the defroster sensor at the bottom of the mounting using a cable tie.

The outdoor unit is now mounted and can be adjusted on the site where it should be set up.

Altri manuali per DHP-A

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Danfoss Unità di controllo

Danfoss

Danfoss PCVD Manuale utente

Danfoss

Danfoss MSV-F Plus DN 15 Manuale utente

Danfoss

Danfoss PM3 Istruzioni operative e di manutenzione

Danfoss

Danfoss ASV-M Manuale utente

Danfoss

Danfoss Link SCM Manuale utente

Danfoss

Danfoss ICSH 25 Manuale utente

Danfoss

Danfoss SVA-S SS 15 Manuale utente

Danfoss

Danfoss ASV-PV series Manuale utente

Danfoss

Danfoss AFQM Manuale utente

Danfoss

Danfoss POV Series Manuale utente

Danfoss

Danfoss ASV-PV Manuale utente

Danfoss

Danfoss TWA-Z Gen. 2011 Manuale utente

Danfoss

Danfoss VCM 46 Manuale utente

Danfoss

Danfoss 1000 Hz Control Card MK-I Manuale utente

Danfoss

Danfoss PVG 100 Manuale utente

Danfoss

Danfoss MCO 101 Manuale utente

Danfoss

Danfoss MCV111B Series Manuale utente

Danfoss

Danfoss MSV-F2 DN15 - 400 Manuale utente

Danfoss

Danfoss EKC 102A Manuale utente

Danfoss

Danfoss VLT HVAC Drive FC 102 Manuale utente

Danfoss

Danfoss AMV 110 NL AQT Manuale utente

Danfoss

Danfoss KP 15 Manuale utente

Danfoss

Danfoss MBC 5000 Manuale utente

Danfoss

Danfoss DSV 1 Manuale utente

Manuali Unità di controllo popolari di altre marche

Festo

Festo Compact Performance CP-FB6-E Manuale elenco delle parti

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuale utente

JS Automation

JS Automation MPC3034A Manuale utente

JAUDT

JAUDT SW GII 6406 Series Guida rapida

Spektrum

Spektrum Air Module System Manuale utente

BOC Edwards

BOC Edwards Q Series Manuale utente

KHADAS

KHADAS BT Magic Manuale utente

Etherma

Etherma eNEXHO-IL Manuale utente

PMFoundations

PMFoundations Attenuverter Manuale utente

GEA

GEA VARIVENT Manuale utente

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuale utente

Altronix

Altronix LINQ8PD Istruzioni per il montaggio

Eaton

Eaton Powerware Series Manuale utente

WAGO

WAGO 750-407/040-000 Manuale utente

Sony

Sony CCU-590 Manuale utente

Graco

Graco 25D614 Manuale utente

Task Force Tips

Task Force Tips YE-RF-900 Manuale di programmazione

Shini

Shini SPV-U Series Manuale utente