Danfoss DEVI DEVIreg 330 Manuale utente
www.DEVI.com
Installation Guide
DEVIreg™ 330 (+60 °С to +160 °C)
Electronic Thermostat
EN
DEVIreg™ 330 (+60 °C to +160 °C)
3Installation Guide
1 Introduction
DEVIreg™ 330 is an electronic thermostat to be installed in
electric cabinets with DIN rail attachment. The thermostat
must be installed via an all-pole disconnection switch.
Either a wire sensor or an external air sensor must be used
to measure and control the desired temperature.
The thermostat has a button to adjust the temperature set-
ting, with a scale from +60 °C to +160 °C. An LED indicator
shows standby periods (green light) and heating periods
(red light).
More information on this product can also be found at:
devi.com
1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
1.1 Technical Specifications . . . . . . . . . . . . . . . . . . . . 4
1.2 Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . 5
2 Mounting Instructions . . . . . . . . . . . . . . . . . . . . . . . . 6
3 Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
4 Disposal Instruction . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Table of Contents
DEVIreg™ 330 (+60 °C to +160 °C)
Installation Guide4
1.1 Technical Specifications
Operation voltage 220-240 V~, 50-60 Hz
Standby power consumption Max 0,25 W
Relay:
Resistive load
Inductive load
Max 16 A / 3680 W @ 230 V
cos φ= 0,3 max1A
Sensing units NTC 16,7 kOhm at 100 °C
Sensing values:
25 °C
50 °C
100 °C
120 °C
170 °C
300 kOhm
99,4 kOhm
16,7 kOhm
8,8 kOhm
2,35 kOhm
Hysteresis ± 0,4 °C
Ambient temperature 10 °C to +50 °C
Temperature range +60 °C to +160 °C
Cable specification max 1x4 mm2or 2x2,5 mm2
Ball pressure temperature 75 °C
Pollution degree 2 (domestic use)
Type 1C
Storage temperature -20 °C to +65 °C
DEVIreg™ 330 (+60 °C to +160 °C)
5Installation Guide
IP class 20
Protection class Class II
Dimensions 86 x 36 x 58 mm
Weight 83 g
The product complies with the EN/IEC Standard“Automatic
electrical controls for household and similar use”:
• EN/IEC 60730-1 (general)
• EN/IEC 60730-2-9 (thermostat)
1.2 Safety Instructions
Make sure the mains supply to the thermostat is turned off
before installation.
Please also note the following:
• The installation of the thermostat must be done by an
authorized and qualified installer according to local
regulations.
• The thermostat must be connected to a power supply
via an all-pole disconnection switch.
• The sensor is to be considered as live voltage. Have this
in mind if the sensor must be extended.
• Always connect the thermostat to continuous power
supply.
• Do not expose the thermostat to moisture, water,
dust, and excessive heat.
DEVIreg™ 330 (+60 °C to +160 °C)
Installation Guide6
• If temperature wire sensor is applied on conductive
surface it must be installed with additional electrical
insulation.
• Caution: temperature sensor, heated surface and heat-
ing cable could have really high temperature.
• Sensor, conduit, fixing materials, etc. should be speci-
fied to be able to withstand temperatures applied by
application.
• Caution: Temperature sensor with silicon cable should
not be installed in concrete, aggressive and corrosive
environment, etc.
2 Mounting Instructions
Please observe the following placement guidelines:
• Install the thermostat in an electric cabinet with DIN
rail attachment or a separate DIN attachment accord-
ing to local regulation on IP classes.
• Do not place the thermostat in a way that it will be
exposed to direct sunlight.
Follow the steps below to mount the thermostat:
1. Click the thermostat on to the DIN rail attachment.
2. Connect the thermostat according to the connection
diagram.
DEVIreg™ 330 (+60 °C to +160 °C)
7Installation Guide
IP20
10T50 D330
+60°C to
+160°C
8765
N
4321 L
Mains
220-240V~
250V~
16 (1) A
Sensor
Load
max. 16 A
(heating)
Max. 10 A
(cooling)
The screen of the heating cable must be connected
to the earth conductor of the power supply cable by
using a separate connector.
Note: When you use the wire sensor for floor heating,
always install the sensor in a conduit.
3. Turn on the power supply.
DEVIreg™ 330 (+60 °C to +160 °C)
Installation Guide8
3 Warranty
4 Disposal Instruction
DEVIreg™ 330 (+60 °C to +160 °C)
9Installation Guide
DEVIreg™ 330 (+60 °C to +160 °C)
Installation Guide10
Questo manuale è adatto per i seguenti modelli
1
Indice
Altri manuali Danfoss Termostato
Danfoss
Danfoss FH-CWD Manuale utente
Danfoss
Danfoss ECtemp 535 Manuale utente
Danfoss
Danfoss TP75-RF Manuale utente
Danfoss
Danfoss living connect Manuale utente
Danfoss
Danfoss TP5000 si range Manuale utente
Danfoss
Danfoss FP975 Manuale utente
Danfoss
Danfoss Icon Master Manuale utente
Danfoss
Danfoss TP5E Manuale utente
Danfoss
Danfoss RET MD Guida alla risoluzione dei problemi
Danfoss
Danfoss FH-WS Manuale utente
Danfoss
Danfoss ECL Comfort 310 Manuale utente
Danfoss
Danfoss ECtemp 531 Manuale utente
Danfoss
Danfoss EFET 160 Manuale utente
Danfoss
Danfoss ECL Comfort 310, A367 Manuale utente
Danfoss
Danfoss RET B-LS Manuale utente
Danfoss
Danfoss RET2000B-RF + RX1-S Manuale utente
Danfoss
Danfoss BasicPlus2 Manuale utente
Danfoss
Danfoss DBR Manuale utente
Danfoss
Danfoss 088L5130 Manuale utente
Danfoss
Danfoss DEVIreg 330 Manuale utente
