Danfoss ECtemp 130 Manuale utente
ECtemp
130
Electronic Thermostat
Installation Guide
electricheating.danfoss.com
ECtemp 130
Installation Guide2
ECtemp 130
3Installation Guide
1 Introduction
ECtemp 130 is an electronic thermostat to be installed di-
rectly on the wall. It is provided with a oor sensor to measure
and control the desired oor temperature.
The thermostat has a button for adjusting the temperature
setting with a scale from ( ) 1 to 5 (each step corresponds to
approximately 9°C). Furthermore, the thermostat has an LED
indicator showing standby periods (green light) and heating
periods (red light).
More information on this product can also be found at:
ectemp.danfoss.com
Table of Contents
1 Introduction . . . . . . . . . . . . . . . . . . . . . . . 3
1.1 Technical Specications . . . . . . . . . . . . 4
1.2 Safety Instructions . . . . . . . . . . . . . . . 5
2 Mounting Instructions . . . . . . . . . . . . . . . . . 6
3 Settings . . . . . . . . . . . . . . . . . . . . . . . . . 10
3.1 Temperature Settings. . . . . . . . . . . . . 10
4 Warranty. . . . . . . . . . . . . . . . . . . . . . . . . 14
5 Disposal Instruction . . . . . . . . . . . . . . . . . 16
ECtemp 130
Installation Guide4
1.1 Technical Specications
Operation voltage 220-240V~, 50Hz
Power consumption Max 5W
Relay:
Resistive load
Inductive load
Max 16A / 3680W @ 230V
cos φ= 0.3 max 1A
Sensing units NTC 15 kOhm at 25°C
Sensing values:
0 °C
25 °C
50 °C
42 kOhm
15 kOhm
6 kOhm
Hysteresis ± 0,2 °C
Ambient temperature 0 to +30°C
Frost protection temperature 5 °C -
Temperature range ( ) 5–45 °C
Cable specication max 1x4 mm² or 2x2,5 mm²
Ball pressure temperature 75 °C
Pollution degree Degree 2 (domestic use)
Type 1C
Storage temperature -20 to +65°C
IP class 30
Protection class Class II -
ECtemp 130
5Installation Guide
Dimensions 82 x 82 x 36 mm
Weight 90 g
The product complies with the EN/IEC Standard «Automatic
electrical controls for household and similar use»:
• EN/IEC 60730-1 (general)
• EN/IEC 60730-2-9 (thermostat)
1.2 Safety Instructions
Make sure the mains supply to the thermostat is turned o
before installation.
IMPORTANT: When the thermostat is used to control a
oor heating element in connection with a wooden oor or
similar material, always use a oor sensor and never set the
maximum oor temperature to more than 35°C.
Please also note the following:
• The installation of the thermostat must be done by an
authorized and qualied installer according to local
regulations.
• The thermostat must be connected to a power supply
via an all-pole disconnection switch.
• The sensor is to be considered as live voltage. Have
this in mind if the sensor must be extended.
ECtemp 130
Installation Guide6
• Always connect the thermostat to continuous power
supply.
• Do not expose the thermostat to moisture, water,
dust, and excessive heat.
2 Mounting Instructions
Please observe the following placement guidelines:
Place the thermostat at a suitable height on
the wall (typically 80-170cm.).
In wet rooms, place the thermostat
according to local regulation on IP classes.
Do not place the thermostat on the inner
side of an exterior wall.
ECtemp 130
7Installation Guide
• Place the oor sensor in a conduit in an
appropriate place where it is not exposed
to sunlight or draft from door openings.
• Equally distant and >2cm from two heat-
ing cables.
• The conduit should be ush with the
oor surface - countersink the conduit if
necessary.
• Route the conduit to the connection box.
• The bending radius of the conduit must
be min 50mm.
ECtemp 130
Installation Guide8
Follow the steps below to mount the thermostat:
1. Open the thermostat:
• Lift o the button using a small screwdriver.
• Loosen the screw which holds the front.
• Push down the release tab at the top of the
thermostat using a at object while slowly pulling o
the front cover.
ECtemp 130
9Installation Guide
2. Fasten the thermostat directly to the wall by driving
the screws through the holes in each side of the
thermostat.
1= Screw holes for fastening the thermostat.
3. Connect the thermostat according to the
connectiondiagram.
IP30
0T30
D130
NTC
1234
Sensor
Max.Load
16 (1) A
Mains
220-240V~
N
LOAD
L
LOAD
NL
The screen of the heating cable must be connected
to the earth conductor of the power supply cable by
using a separate connector.
Note: Always install the oor sensor in a conduit in
the oor.
ECtemp 130
Installation Guide10
4. Install the front cover and button in the reverse order
of disassembly.
5. Turn on the power supply.
3 Settings
3.1 Temperature Settings
How to change the minimum and maximum oor
temperatures
1. Lift o the adjustment
button using a thin
screwdriver. (1)
2. Move the pins to the
desired positions. (2 and 3)
3. Put the adjustment button
back in place.
Please be aware of the following:
• The oor temperature is measured where the sensor
is placed.
• The temperature of the bottom of a wooden oor can
be up to 10 degrees higher than the top.
• Floor manufactures often specify the max
temperature on the top surface of the oor (usually
27-28˚C).
Indice
Altri manuali Danfoss Termostato
Danfoss
Danfoss LinkFT Manuale utente
Danfoss
Danfoss TP5001 series Manuale utente
Danfoss
Danfoss RET1000 B Manuale utente
Danfoss
Danfoss RT2-RF Manuale utente
Danfoss
Danfoss living connect Z Manuale utente
Danfoss
Danfoss BasicPlus2 WT-T Manuale utente
Danfoss
Danfoss TP75-RF Manuale utente
Danfoss
Danfoss ECL Comfort 210 Manuale utente
Danfoss
Danfoss Link FT Manuale utente
Danfoss
Danfoss TP4000 Range Manuale utente
Danfoss
Danfoss RET M Istruzioni operative
Danfoss
Danfoss TP75 Manuale utente
Danfoss
Danfoss RET MD Guida alla risoluzione dei problemi
Danfoss
Danfoss TP9000 Si Manuale utente
Danfoss
Danfoss TP5000 si range Manuale utente
Danfoss
Danfoss RET2000B-RF + RX1-S Manuale utente
Danfoss
Danfoss RT 270 Manuale utente
Danfoss
Danfoss KP 61 Manuale utente
Danfoss
Danfoss GreenCon RC-T2 Manuale utente
Danfoss
Danfoss EFET 130 Manuale utente
