DanVex DEH-1700wp Manuale utente
Dehumidifiers for swimming pools
DEH-1700wp
DEH-2000wp
Instruction manual
R
www.danvex.fi
1
Please read this instruction manual carefully and save it before using the dehumidifier. If you
have any questions about using the dehumidifier, please contact Your dealer.
R
www.danvex.fi 2
INTRODUCTION .............................................................................................................................
PRECAUTIONARY MEASURES .....................................................................................................
DESCRIPTION OF THE DEHUMIDIFIER .......................................................................................
WIRING DIAGRAMS .......................................................................................................................
INSTALLATION NOTE ....................................................................................................................
START-UP AND OPERATION (DESCRIPTION OF THE CONTROL PANEL) ................................
REMOTE CONTROL AND ERROR CODES ...................................................................................
DEHUMIDIFIER MAINTENANCE ....................................................................................................
TECHNICAL SPECIFICATIONS ......................................................................................................
WARRANTY TERMS AND WARRANTY CARD ..............................................................................
CONTENTS
3
4
6
7
8
9
11
12
13
14
R
www.danvex.fi
INTRODUCTION
MODELS:
DEH-1700wp
DEH-2000wp
All the dehumidifiers described in this manual are designed to maintain the relative
humidity of indoor air in the range from 40% to 99%, at air temperature from +10°C to
+32°C.
3
R
www.danvex.fi 4
Read this manual carefully for safety before
you start operating the dehumidifier. Below are
the symbols used in this manual.
If dirt sticks to the plug of the power cord
or plug and socket connection is loose, it
may cause fire or electric shock.
PRECAUTIONARY MEASURES
CAUTION
Remove any dirt from the plug
of the power cord.
There should be no breaks in the cord
or its artificial extensions.
Do not scratch or bend the power cord.
Do not place heavy objects on the power
cord, heat it, or expose to other factors. The
cable may be damaged, which can lead to fire
or electric shock.
Consult Your dealer on installation
of the device.
Do not insert fingers or any objects
into the air intake/ outlet.
Do not attempt self-repair or re-installation
of the device.
If this is done incorrectly, it may cause fire,
electric shock, water leakage, etc.
Contact Your dealer.
Strictly forbidden
Be sure to follow the
instructions
Provide grounding
Unplug the power cord from
network
Never store anything on the
device
Electric shock hazard
Never insert fingers
or any items
Do not disconnect / do not connect
power supply during operation
If during operation there is something
unusual (burning smell, etc.), turn
off the device and disconnect it from
the network
Use grounding.
In case of incorrect operation of the device,
contact Your dealer.
Avoid contact of the grounding
wire with gas and water pipes,
lightning rod or telephone cable. If
the grounding is made incorrectly,
it can lead to defeat electric shock
hazard.
R
www.danvex.fi
5
This may cause fire or deformation.
PRECAUTIONARY MEASURES
CAUTION
Do not use insect repellent or solvents.
Before cleaning the device switch it off
and disconnect the power cable from
the mains.
It can cause a short circuit that may result
in electric shock or fire.
Do not clean the device with water.
●This can lead to electric shock.
As the fan rotates at high speed, cleaning of
operating device can cause injury.
If the device is installed in a damp
location, ensure its isolation from
moisture.
If you do not provide isolation
of the device from moisture, it may
cause electric shock.
If You do not, the device may accumulate dirt
and cause a fire.
If You are not going to use the device
during a long period, unplug it from
the mains.
Do not install the device in a place where
there is flammable gas.
Do not install the device where in unsafe
operation conditions.
Do not press the switches with wet hands.
This may cause electric shock.
Unassisted installation of the device is
forbidden.
If this is performed incorrectly, it may cause
fire, electric shock, water leakage, etc.
Please contact Your dealer or technician.
Do not pull on the power cord.
R
www.danvex.fi 6
DEHUMIDIFIER DESCRIPTION
AIR DEHUMIDIFIERS: DEH-1700wp and DEH-2000wp
Power cordPower cord
Moist air input
Mounting bracket
Dry air output Control panel
Drain hose
R
www.danvex.fi 7
WIRING DIAGRAM
DEH-1700wp, DEH-2000wp
SINGLEPHASE (1PH/50 Hz)
Датчик
Датчик системы
Вывод на дисплей PCB
Главный контроллер PCB
вентилятора
Компрессо
Main controller PCB
Humidity detector
Air temperature sensor
System defrost sensor
PCB display representation
Compressor
Fan motor
Power source
Transformer
Protection from low pressure
Protection from high pressure
R
www.danvex.fi 8
INSTALLATION NOTE
Mounting of the dehumidifier on the wall:9
Step 1: Select the correct position for mounting on the wall, depending on the size of the
holes set and the holes positions of the wall mount bracket. The place of installation should
guarantee the vertical position of the dehumidifier. Mark places for drilling.
Step 2: Use hammer drills to drill holes with depth of 8 ± 0.5 cm Then use the anchor bolts
and install them into the holes with a hammer.
Step 3: Install the wall bracket with anchor bolts in the correct position. Please, provide
secure fixing of the bracket using nuts and washers. Don't forget to hold the bracket in the
correct position during installation.
Step 4: Install the dryer on the wall bracket.
Step 5: Connect the drain hose to the dehumidifier. Turn on the dehumidifier for trial use.
Check the device for presence of abnormal vibration and noise.
Step 6: Installation is finished and the dehumidifier is ready for use.
Installation diagram.
In case of indoor installation of the device, provide availability of free space for its
maintenance. The premises, where the device is installed, must be ventilated.
Before installation of the dehumidifier:
Before shipment from the factory all the dehumidifiers are subject to tests. Unpack the box
and check for damage on the surface of the device, as well as for completeness of
components in accordance with the list specified in the instructions. If You find any damage,
do not attempt to install the humidifier and immediately contact the supplier.
IF DURING TRANSPORT THE DRYER WAS LYING ON THE SIDE, IT NEEDS
TO BE LEFT UPRIGHT FOR AT LEAST 24 HOURS BEFORE THE START OF
ITS OPERATION!!!
(failure to perform this may cause damage to the dryer and void your warranty)
CAUTION!!!
R
www.danvex.fi
9
Control panel.
Button Function
1. “Power” / ”ON/OFF button
Press this button to start the machine, it enters start-up mode after the buzzer buzzes twice
Press this button to stop the machine, it enters stop mode after the buzzer buzzes once
2. “Timer” button(for 2G controller)
A,In standby mode, press “timer” to set Auto starting time, “on time”will flash in screen, and click “+”
or “-” to adjust the time;
B, In working mode, press “timer” to set Auto stop time, “off time”will flash in screen, and click “+” or
“-” to adjust the time;
3. “+” button
Press this button directly to increase the set humidity. Buzzer buzzes once for each pressing and the
set humidity decreases by 1% RH. Successive operation can be achieved by pressing this button
successively. Press “Time” button before pressing this button, the time (hour) can be increased.
4. “－” button
Press this button directly to decrease the set humidity. Buzzer buzzes once for each pressing and the
set humidity decreases by 1%RH. Successively operation can be achieved by pressing this button
successively. Press “Time” button before pressing this button, the time (minute) can be decreases.
Operating the machine
1.. Energize the power, the dehumidifier will beep for onc
2.
. Press the “On/Off” button for once, the LCD display is light. After all displays are normal, the LCD
displays current environment humidity;
3.
. Setting of humidity: press “+” and －” buttons to set the required humidity.
When the set humidity is 3% less than current humidity, the dehumidifier works; when the set
humidity is 3% more than current humidity，the dehumidifier stops.
4.
. When the set humidity is less than 30%, the dehumidifier enters the mo of successive
dehumidification.
5.. Setting of preset tim
Press the “Time” button for the first time, the “hour” time on the display flashes，press “+”and“－”to
adjust the current hour and minute time；Press the “Time” button for the second time，the “Start-up
time” on the LCD flashes， press “+”and“－”to adjust the current hour and minute time；Press the
“Time” button for the third time ， the “Stop time” on the LCD flashes ， Press
“+”and“－”to adjust the current hour and time；Press the “Time” button for the forth time，the mode
of “preset time ”can be canceled.
6.. After setting the mode of preset time, if the dehumidifier is shut off, it wi operate the whole mode of
preset time; if it is in operation, it will operate the mode of “preset stop time”.
Questo manuale è adatto per i seguenti modelli
1
Indice
Altri manuali DanVex Deumidificatore
DanVex
DanVex DEH-1600i Manuale utente
DanVex
DanVex DEH-3K Manuale utente
DanVex
DanVex DEH-400P Manuale utente
DanVex
DanVex AD-400 Manuale utente
DanVex
DanVex AD-200 Manuale utente
DanVex
DanVex AD-200 Manuale utente
DanVex
DanVex AD-800 Istruzioni operative
DanVex
DanVex DEH-900i Manuale utente
DanVex
DanVex DEH-500i Manuale utente
DanVex
DanVex DD Series Manuale utente
